Arduino® Nano 33 BLE
Sehlahisoa Reference Manual
SKU: ABX00030
Tlhaloso
Nano 33 BLE ke mojule oa boholo bo bonyenyane o nang le mojule oa NINA B306, o thehiloeng ho Nordic nRF52480 mme o na le Cortex M4F le IMU ea 9-axis. Mojule o ka hlongoa joalo ka karolo ea DIP (ha o kenya lihlooho tsa pin) kapa joalo ka karolo ea SMT, o e kopanya ka kotloloho ka lipampiri tse entsoeng ka masela.
Libaka tse reriloeng:
Moetsi, lintlafatso, maemo a ts'ebeliso ea IoT ea mantlha
Likaroloana
- NINA B306 Module
- processor
- 64 MHz Arm® Cortex-M4F (ka FPU)
- 1 MB Flash + 256 KB RAM
- Bluetooth 5 multiprotocol radio
- 2 Mbps
- CSA #2
- Advertising Extensions
- Nako e telele
- +8 dBm TX matla
- -95 dBm kutloisiso
- 4.8 mA ho TX (0 dBm)
- 4.6 mA ho RX (1 Mbps)
- Balun e kopantsoeng e nang le 50 Ω e phethiloeng e le 'ngoe
- IEEE 802.15.4 tšehetso ea seea-le-moea
- Khoele
- Zigbee
- processor
- Pheripherals
- Lebelo le felletseng la 12 Mbps USB
- NFC-A tag
- Setsi sa ts'ireletso sa Arm CryptoCell CC310
- QSPI/SPI/TWI/I²S/PDM/QDEC
- Lebelo le phahameng 32 MHz SPI
- Quad SPI interface 32 MHz
- EasyDMA bakeng sa lihokelo tsohle tsa dijithale
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR co-processor
- LSM9DS1 (IMU ea li-axis tse 9)
- liteishene tse 3 tse potlakisang, liteishene tse 3 tsa sekhahla, liteishene tse 3 tsa matla a khoheli
- ± 2 / ± 4 / ± 8 / ± 16 g ho potlakisa lebelo le felletseng
- ± 4 / ± 8 / ± 12 / ± 16 gauss makenete sekala se felletseng
- ± 245 / ± 500 / ± 2000 dps sekhahla sa angular sekala se felletseng
– 16-bit data e hlahisoang - MPM3610 DC-DC
- E laola tlhahiso ea molumotage ho tloha ho 21V ka bonyane ba 65% effciency @minimum load
- Ho feta 85% ho sebetsa hantle @12V
Boto
Joalo ka liboto tsohle tsa Nano form factor, Nano 33 BLE ha e na tjhaja ea betri empa e ka tsamaisoa ka USB kapa lihlooho.
HLOKOMELA: Arduino Nano 33 BLE e ts'ehetsa 3.3VI/Os feela 'me HA E mamelle 5V kahoo ka kopo etsa bonnete ba hore ha o hokele mats'oao a 5V ka kotloloho ho boto ena kapa e tla senyeha. Hape, ho fapana le liboto tsa Arduino Nano tse tšehetsang ts'ebetso ea 5V, pinana ea 5V HA E fane ka vol.tage empa ho e-na le hoo e hokahane, ka jumper, ho kenya matla a USB.
Kopo Examples
Maqhubu a molumo: Theha leqhubu la molumo ho bona ka mahlo a kelello maqhubu a molumo. Hokela Arduino 33 Nano BLE le maekrofono kapa amphantle.
Sensor ea sebaka sa sechaba: Ho boloka sebaka sa sechaba ho se ho le bohlokoa ho feta leha e le neng pele ho netefatsa bophelo ba hau, hammoho le ba ba bang. Ka ho hokahanya Arduino Nano 33 BLE ka sensor le pontšo ea LED, u ka etsa sehlopha se khabisoang se u lemosang ha u atamela haufi le batho ba bang.
Sekena sa semela se phetseng hantle: Ho nosetsa limela tsa hau ha se kamehla ho lekaneng ho li boloka li thabile. Mafu, khaello ea khanya ea letsatsi, joalo-joalo e ka ba lintlha tsa bohlokoa bakeng sa limela tse sa pheleng hantle. Boloka limela tsa hau li thabile ka ho theha sebui le ho se koetlisetsa ho lemoha mafu leha e le afe, kaofela ka Arduino Nano 33 BLE
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Max |
| Meeli ea mocheso oa Conservative bakeng sa boto kaofela: | -40 °C (40 °F) | 85°C ( 185 °F) |
Tšebeliso ea Matla
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| PBL | Tšebeliso ea matla e nang le loop e phathahaneng | TBC | mW | ||
| PLP | Tšebeliso ea matla ka mokhoa o fokolang oa matla | TBC | mW | ||
| PMAX | Tšebeliso e Felletseng ea Matla | TBC | mW |
E sebetsa hapeview
Board Topology
Board topology Top
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U1 | NINA-B306 Module BLE 5.0 Module | U6 | MP2322GQH Step Down Converter |
| U2 | Tlhaloso: LSM9DS1TR IMU | PB1 | IT-1185AP1C-160G-GTR Konopo ea ho sututsa |
| DL1 | Led L | DL2 | Matla a Led |
Tlase:
Boto ea topology bot
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| SJ1 | VUSB jumper | SJ2 | D7 Jumper |
| SJ3 | 3v3 Jumper | SJ4 | D8 Jumper |
processor
Main processor ke Cortex M4F e sebetsang ho fihla ho 64MHz. Bongata ba lithakhisa tsa eona li hokahane le lihlooho tsa kantle, leha ho le joalo, tse ling li boloketsoe puisano ea ka hare le module e se nang mohala le li-peripherals tsa kahare tsa I²C (IMU le Crypto).
HLOKOMELA: Ho fapana le liboto tse ling tsa Arduino Nano, lithakhisa tsa A4 le A5 li na le mokhoa o ka hare oa ho hula 'me oa kamehla o tla sebelisoa e le I²C Bese e sebelisoang e le lisebelisoa tsa analog ha e khothalletsoe.
Sefate sa Matla
Boto e ka tsamaisoa ka sehokelo sa USB, VIN, kapa lithakhisa tsa VUSB lihloohong.
Sefate sa matla
HLOKOMELA: Kaha VUSB e fepa VIN ka diode ea Schottky le molaoli oa DC-DC o boletse bonyane matla a ho kenya.tage ke 4.5V bonyane ba phepelo ea matlatage ho tloha ho USB e tlameha ho eketseha ho ea ho voltage sebakeng se pakeng tsa 4.8V le 4.96V ho itšetlehile ka se huloang hona joale.
Ts'ebetso ea Boto
3.1 Ho qala – IDE
Haeba u batla ho kenya Arduino Nano 33 BLE ea hau ha u ntse u le sieo, u lokela ho kenya Arduino Desktop IDE [1] Ho hokela Arduino Nano 33 BLE komporong ea hau, u tla hloka thapo ea USB ea Micro-B. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
3.2 Ho qala – Arduino Web Mohlophisi
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose la Arduino Web Mohlophisi [2], ka ho kenya plugin e bonolo feela.
Arduino Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau.
3.3 Ho qala - Arduino IoT Cloud
Lihlahisoa tsohle tse nolofalitsoeng ke Arduino IoT li tšehetsoa ho Arduino IoT Cloud e u lumellang hore u Log, graph, le ho sekaseka lintlha tsa sensor, ho qala liketsahalo le ho iketsetsa ntlo kapa khoebo ea hau.
3.4 Sample Sketches
Sample litšoantšo tsa Arduino Nano 33 BLE li ka fumanoa ho "Examples" ho Arduino IDE kapa karolong ea "Documentation" ea Arduino Pro websebaka [4]
3.5 Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho ProjectHub [5], Arduino Library Reference [6], le lebenkele la marang-rang [7] moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling
3.6 Pholiso ea Boto
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho khantša boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khoneha ho kenya mokhoa oa bootloader ka ho tlanya habeli konopo ea reset hang ka mor'a ho tima.
Sehokedi Pinouts
4.1 USB
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | VUSB | Matla | Phepelo ea Matla. Haeba boto e tsamaisoa ka VUSB ho tloha hloohong sena ke Output 1 |
| 2 | D- | Tse fapaneng | Lintlha tse fapaneng tsa USB - |
| 3 | D+ | Tse fapaneng | Lintlha tse fapaneng tsa USB + |
| 4 | ID | Analoge | E khetha tšebetso ea Host/Device |
| 5 | GND | Matla | Sebaka sa Matla |
4.2 Lihlooho
Boto e pepesa lihokelo tse peli tsa 15-pin tse ka kopanngoang ka lihlooho tsa phini kapa tsa rekisoa ka li-vias tse nang le li-castelated.
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D13 | Dijithale | GPIO |
| 2 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare ho lisebelisoa tsa kantle |
| 3 | AREF | Analoge | Tlhaloso ea Analog; e ka sebelisoa e le GPIO |
| 4 | A0/DAC0 | Analoge | ADC in/DAC tsoa; e ka sebelisoa e le GPIO |
| 5 | A1 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 6 | A2 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 7 | A3 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 8 | A4/SDA | Analoge | ADC ka; I2C SDA; E ka sebelisoa e le GPIO (1) |
| 9 | A5/SCL | Analoge | ADC ka; I2C SCL; E ka sebelisoa e le GPIO (1) |
| 10 | A6 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 11 | A7 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 12 | VUSB | Matla ka hare/Kantle | Ka tloaelo NC; e ka hokeloa ho phini ea VUSB ea sehokelo sa USB ka ho khutsufatsa a |
| 13 | RST | Digital In | Mongolo o sebetsang-tlase oa ho seta bocha (kopi ea phini ea 18) |
| 14 | GND | Matla | Sebaka sa Matla |
| 15 | VIN | Power In | Ho kenya Matla a Vin |
| 16 | TX | Dijithale | UART TX; e ka sebelisoa e le GPIO |
| 17 | RX | Dijithale | UART RX; e ka sebelisoa e le GPIO |
| 18 | RST | Dijithale | Mongolo o sebetsang-tlase oa ho seta bocha (kopi ea phini ea 13) |
| 19 | GND | Matla | Sebaka sa Matla |
| 20 | D2 | Dijithale | GPIO |
| 21 | D3/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 22 | D4 | Dijithale | GPIO |
| 23 | D5/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 24 | D6/PWM | Dijithale | GPIO e ka sebelisoa e le PWM |
| 25 | D7 | Dijithale | GPIO |
| 26 | D8 | Dijithale | GPIO |
| 27 | D9/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 28 | D10/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 29 | D11/MOSI | Dijithale | SPI MOSI; e ka sebelisoa e le GPIO |
| 30 | D12/MISO | Dijithale | SPI MISO; e ka sebelisoa e le GPIO |
4.3 Debug
Ka lehlakoreng le ka tlase la boto, tlas'a mojule oa puisano, matšoao a debug a hlophisitsoe joalo ka lipampiri tsa liteko tsa 3 × 2 tse nang le 100 mil pitch e nang le pin 4 e tlositsoeng. Pin 1 e bonts'itsoe ho Setšoantšo sa 3 - Maemo a Sehokelo
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare a tla sebelisoa e le voltage referense |
| 2 | SWD | Dijithale | nRF52480 data ea Single Wire Debug |
| 3 | SWCLK | Digital In | nRF52480 Single Wire Debug Clock |
| 5 | GND | Matla | Sebaka sa Matla |
| 6 | RST | Digital In | Kenyo e sebetsang e tlase ea ho seta bocha |
| 1 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare a tla sebelisoa e le voltage referense |
Boitsebiso ba Mechini
5.1 Kemiso ea Boto le Likoti tse Behang
Mehato ea boto e tsoakane pakeng tsa metric le imperial. Mehato ea borena e sebelisetsoa ho boloka gridi ea 100 mil pitch pakeng tsa mela ea phini ho ba lumella ho lekana le boardboard athe bolelele ba boto ke Metric.
Setifikeiti
6.1 Phatlalatso ea Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
6.2 Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Bolelele ba moeli (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokoloho: Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello, le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse hore ha ho le e 'ngoe ea SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Lethathamo la Mokhethoa oa Lintho tse Phahameng haholo
Ho ameha ka tumello e lokollotsoeng hajoale ke ECHA ho teng lihlahisoa tsohle (le liphutheloana) ka bongata bo lekanang le kapa ka holimo ho 0.1%. Ho ea ka tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete leha e le efe ea bohlokoa joalokaha e boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
6.3 Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa lisebelisoa tsa elektronike le motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e amanang le Conflct Minerals, haholo-holo Dodd-Frank Wall Street Reform le Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise ka ho toba kapa ha e sebetsane le likhohlano ka ho toba. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tse loantšanang li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boikitlaetso ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho ipapisitsoe le tlhaiso-leseling eo re e fumaneng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Conflict tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ke mokha o ikarabellang bakeng sa tumellano li ka hlakola mosebelisi
matla a ho tsamaisa thepa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
(1) Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
(2) sesebelisoa sena se tlameha ho amohela tšitiso leha e le efe e amoheloang, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20cm pakeng tsa radiator le 'mele oa hau.
Litaelo tsa mosebelisi bakeng sa lisebelisoa tsa seea-le-moea tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang le eona sebakeng se hlakileng bukeng ea mosebelisi kapa sesebelisoa kapa ka bobeli. Sesebelisoa sena se lumellana le Indasteri
Maemo a RSS a sa tsoeng laesenseng ea Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
(1) sesebelisoa sena se kanna sa se sitise
(2) sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Thempereichara ea ts'ebetso ea EUT e ke ke ea feta 85 ℃ mme ha ea lokela ho ba ka tlase ho -40 ℃.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
Lintlha tsa Khampani
| Maqhubu a maqhubu | Arduino Srl |
| 863-870Mhz | Via Andrea Appiani 25 20900 MONZA Italy |
Litokomane Tsa Litšupiso
| Referense |
Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Leru) | https://create.arduino.cc/editor |
| Cloud IDE Ho qala | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduinoweb-editor-4b3e4a |
| Foramo | http://forum.arduino.cc/ |
| SAMD21G18 | http://ww1.microchip.com/downloads/en/devicedoc/40001884a.pdf |
| NINA W102 | https://www.u-blox.com/sites/default/files/N INA-W1O_DataSheet_%28U BX17065507%29.pdf |
| EA-608-EF | http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf |
| MPM3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
| NINA Firmware | https://github.com/arduino/nina-fw |
| Laebrari ea ECC608 | https://github.com/arduino-libraries/ArduinoECCX08 |
| Laeborari ea LSM6DSL | https://github.com/stm32duino/LSM6DSL |
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://www.arduino.cc/reference/en/ |
| Lebenkele la Arduino | https://store.arduino.cc/ |
Nalane ea Phetoho
| Letsatsi | Khatiso | Liphetoho |
| 04/21/2021 | 1 | Lintlafatso tse akaretsang tsa database |
Arduino® Nano 33 BLE
E fetotsoe: 18/02/2022
Litokomane / Lisebelisoa
 |
ARDUINO ABX00030 Nano 33 BLE Miniature Siized Module [pdf] Bukana ea Mosebelisi ABX00030, Nano 33 BLE, Miniature Siized Module, Nano 33 BLE Miniature Siized Module, ABX00030 Nano 33 BLE Miniature Siized Module |
