Arduino® Nano 33 BLE
Akwụkwọ ntuziaka ngwaahịa
SKU: ABX00030
Nkọwa
Nano 33 BLE bụ modul nke pere mpe nwere modul NINA B306, dabere na Nordic nRF52480 yana nwere Cortex M4F na 9-axis IMU. Enwere ike itinye modul ahụ dị ka akụrụngwa DIP (mgbe ị na-ebunye isi ntụtụ) ma ọ bụ dị ka akụrụngwa SMT, na-ere ya ozugbo site na paịlị nke castellated.
Ebe ebumnuche:
Onye mepụtara, nkwalite, ndapụta ngwa ngwa IoT
Atụmatụ
- NINA B306 Modul
- Nhazi
- 64 MHz Arm® Cortex-M4F (ya na FPU)
- 1 MB Flash + 256 KB RAM
- Bluetooth 5 multiprotocol redio
- 2 Mbps
- CSA #2
- Mgbatị mgbasa ozi
- Ogologo ogologo
- + 8 dBm TX ike
- -95 dBm mmetụta
- 4.8mA na TX (0 dBm)
- 4.6mA na RX (1 Mbps)
- Balun agbakwunyere nwere mmepụta nwere ngwụcha otu 50 Ω
- IEEE 802.15.4 nkwado redio
- eri
- Zigbee
- Nhazi
- Akụkụ
- Ọsọ zuru oke 12Mbps USB
- NFC-A tag
- Arm CryptoCell CC310 nchekwa subsystem
- QSPI/SPI/TWI/I²S/PDM/QDEC
- Ọsọ dị elu 32 MHz SPI
- Quad SPI interface 32 MHz
- EasyDMA maka oghere dijitalụ niile
- 12-bit 200 kps ADC
- 128-bit AES/ECB/CCM/AAR ngalaba-processor
- LSM9DS1 (9 axis IMU)
- Ọwa osooso 3, ọwa ọnụọgụ ọnụọgụ 3, ọwa oghere magnetik 3
- ± 2 / ± 4 / ± 8 / ± 16 g linear osooso zuru oke
- ± 4 / ± 8 / ± 12 / ± 16 gauss magnetik zuru oke
- ± 245 / ± 500 / ± 2000 dps ọnụego angular zuru oke
- 16-bit data mmepụta - MPM3610 DC-DC
- Na-ahazi ntinye voltage si ruo 21V nwere opekempe nke 65% arụmọrụ @ kacha nta
- Karịrị 85% arụmọrụ @12V
The Board
Dịka bọọdụ ụdị Nano niile, Nano 33 BLE enweghị chaja batrị mana enwere ike ịkwado ya site na USB ma ọ bụ nkụnye eji isi mee.
IHE: Arduino Nano 33 BLE na-akwado naanị 3.3VI / OS na ọ bụghị 5V na-anabata ya, biko jide n'aka na ị naghị ejikọta akara 5V ozugbo na bọọdụ a ma ọ bụ na ọ ga-emebi. Ọzọkwa, n'adịghị ka bọọdụ Arduino Nano na-akwado ọrụ 5V, pin 5V anaghị enye vol.tage mana ejikọrọ ya, site na jumper, na ntinye ike USB.
Ngwa Examples
Ụdị ụda dị iche iche: Mepụta ụdịdị ụda dị iche iche iji were anya nke uche hụ ugboro ugboro. Jikọọ Arduino 33 Nano BLE na igwe okwu ma ọ bụ amplee.
Ihe mmetụta ndọpụ uche ọha: Idobe anya mmekọrịta abụrụla ihe dị mkpa karịa mgbe ọ bụla iji hụ na nke gị, yana ahụike nke ndị ọzọ. Site na ijikọ Arduino Nano 33 BLE na ihe mmetụta na ihe ngosi LED, ị nwere ike ịmepụta otu wearable band nke na-eme ka ị mara mgbe ị na-abịaru ndị ọzọ nso.
Nyocha osisi nwere ahụike: Ịgba osisi gị mmiri anaghị ezuru mgbe niile iji mee ka ha nwee obi ụtọ. Ọrịa, enweghị ìhè anyanwụ, wdg nwekwara ike bụrụ ihe dị mkpa maka osisi na-adịghị mma. Mee ka osisi gị nwee obi ụtọ site na ịmepụta onye nchọpụta na ịzụ ya ka ọ chọpụta ọrịa ọ bụla, ha niile nwere Arduino Nano 33 BLE
Ogo
Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Oke |
| Oke thermal Conservative maka bọọdụ dum: | -40 Celsius (40 Celsius) | 85°C (185°F) |
Oriri ike
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| PBL | Oriri ike na akaghị aka | TBC | mW | ||
| PLP | Oriri ike na ọnọdụ ike dị ala | TBC | mW | ||
| PMAX | Oriri ike kacha | TBC | mW |
Arụ ọrụ gafereview
Board Topology
Board topology Top
| Ref. | Nkọwa | Ref. | Nkọwa |
| U1 | NINA-B306 Modul BLE 5.0 Modul | U6 | MP2322GQH Ntụgharị Nkwụghachi azụ |
| U2 | LSM9DS1TR ihe mmetụta IMU | PB1 | IT-1185AP1C-160G-GTR bọtịnụ pịa |
| DL1 | Onye ndu L | DL2 | Ike idu |
N'okpuru:
Board topology bot
| Ref. | Nkọwa | Ref. | Nkọwa |
| SJ1 | VUSB jumper | SJ2 | D7 jumper |
| SJ3 | 3v3 onye na-awụlikwa elu | SJ4 | D8 jumper |
Nhazi
Main Processor bụ Cortex M4F na-agba ọsọ ruo 64MHz. Ejikọrọ ọtụtụ ntụtụ ya na nkụnye eji isi mee n'èzí, agbanyeghị, ụfọdụ echekwabara maka nkwurịta okwu nke ime ya na modul ikuku yana akụkụ ime I²C dị n'ime ụlọ (IMU na Crypto).
IHE: N'adịghị ka bọọdụ Arduino Nano ndị ọzọ, atụdo A4 na A5 nwere ndọghachi azụ na ndabara nke a ga-eji dị ka ụgbọ ala I²C nke ejiri dị ka ntinye analọgụ adịghị atụ aro.
Osisi Ike
Enwere ike ịgbanye osisi ahụ site na njikọ USB, VIN, ma ọ bụ VUSB ntụtụ na nkụnye eji isi mee.
Osisi ike
IHE: Ebe ọ bụ na VUSB na-enye VIN nri site na Schottky diode yana onye na-achịkwa DC-DC kọwapụtara ntinye ntinye kacha nta.tage bụ 4.5V kacha nta ọkọnọ voltage si na USB ga-abawanye na voltage na nso n'etiti 4.8V ka 4.96V dabere na ugbu a na-adọta.
Ọrụ Board
3.1 Mmalite – IDE
Ọ bụrụ na ịchọrọ ịme mmemme Arduino Nano 33 BLE gị mgbe ị nọ n'èzí, ịkwesịrị ịwụnye Arduino Desktop IDE [1] Iji jikọọ Arduino Nano 33 BLE na kọmputa gị, ị ga-achọ eriri USB Micro-B. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara.
3.2 Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọdụ Arduino niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe.
Arduino Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite ihe osise gị na bọọdụ gị.
3.3 Mmalite – Arduino IoT igwe ojii
A na-akwado ngwaahịa Arduino IoT niile na Arduino IoT Cloud nke na-enye gị ohere ịbanye, eserese, na nyochaa data sensọ, kpalite ihe omume ma rụọ ọrụ ụlọ ma ọ bụ azụmahịa gị.
3.4 Sampna Sketches
SampEnwere ike ịhụ ihe osise maka Arduino Nano 33 BLE ma na “Examples” menu na Arduino IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino Pro websaịtị [4]
3.5 Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub [5], Arduino Library Reference [6], na ụlọ ahịa dị n'ịntanetị [7] ebe. ị ga-enwe ike iji sensọ, actuators na ndị ọzọ mejuo osisi gị
3.6 bọọdụ mgbake
Bọdụ Arduino niile nwere ihe nrụnye bootloader nke na-enye ohere iji eriri USB na-ebunye bọọdụ ahụ. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo emechara.
Pinouts njikọ
4.1 USB
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | VUSB | Ike | Ntinye ntinye ike. Ọ bụrụ na etinyere bọọdụ ahụ site na VUSB site na nkụnye eji isi mee nke a bụ ihe nrụpụta 1 |
| 2 | D- | dị iche iche | USB data dị iche iche - |
| 3 | D+ | dị iche iche | USB data dị iche iche + |
| 4 | ID | Analọg | Na-ahọpụta ọrụ onye ọbịa/ngwaọrụ |
| 5 | GND | Ike | Ala Ike |
4.2 nkụnye eji isi mee
Osisi ahụ na-ekpughe njikọ abụọ nke 15-pin nke enwere ike ijikọta isi ntụtụ ma ọ bụ were ya na-ere ya site na vias castellated.
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | D13 | Dijitalụ | GPIO |
| 2 | + 3V3 | Nwepu Ike | Mbupute ike dị n'ime na ngwaọrụ mpụga |
| 3 | AREF | Analọg | Ntuziaka Analog; enwere ike iji ya dị ka GPIO |
| 4 | A0/DAC0 | Analọg | ADC na/DAC pụọ; enwere ike iji ya dị ka GPIO |
| 5 | A1 | Analọg | ADC n'ime; enwere ike iji ya dị ka GPIO |
| 6 | A2 | Analọg | ADC n'ime; enwere ike iji ya dị ka GPIO |
| 7 | A3 | Analọg | ADC n'ime; enwere ike iji ya dị ka GPIO |
| 8 | A4/SDA | Analọg | ADC n'ime; I2C SDA; Enwere ike iji dị ka GPIO (1) |
| 9 | A5/SCL | Analọg | ADC n'ime; I2C SCL; Enwere ike iji dị ka GPIO (1) |
| 10 | A6 | Analọg | ADC n'ime; enwere ike iji ya dị ka GPIO |
| 11 | A7 | Analọg | ADC n'ime; enwere ike iji ya dị ka GPIO |
| 12 | VUSB | Ịbata/Ọpụpụ | Na-emekarị NC; enwere ike ijikọ na pin VUSB nke njikọ USB site na mkpirisi a |
| 13 | RST | Digital In | Ntinye nrụpụta dị ala na-arụ ọrụ (ụdị nke pin 18) |
| 14 | GND | Ike | Ala Ike |
| 15 | VIN | Ike In | Ntinye ike Vin |
| 16 | TX | Dijitalụ | USART TX; enwere ike iji ya dị ka GPIO |
| 17 | RX | Dijitalụ | USART RX; enwere ike iji ya dị ka GPIO |
| 18 | RST | Dijitalụ | Ntinye nrụpụta dị ala na-arụ ọrụ (ụdị nke pin 13) |
| 19 | GND | Ike | Ala Ike |
| 20 | D2 | Dijitalụ | GPIO |
| 21 | D3/PWM | Dijitalụ | GPIO; enwere ike iji ya dị ka PWM |
| 22 | D4 | Dijitalụ | GPIO |
| 23 | D5/PWM | Dijitalụ | GPIO; enwere ike iji ya dị ka PWM |
| 24 | D6/PWM | Dijitalụ | Enwere ike iji GPIO mee PWM |
| 25 | D7 | Dijitalụ | GPIO |
| 26 | D8 | Dijitalụ | GPIO |
| 27 | D9/PWM | Dijitalụ | GPIO; enwere ike iji ya dị ka PWM |
| 28 | D10/PWM | Dijitalụ | GPIO; enwere ike iji ya dị ka PWM |
| 29 | D11/MOSI | Dijitalụ | SPI MOSI; enwere ike iji ya dị ka GPIO |
| 30 | D12/MISO | Dijitalụ | SPI MISO; enwere ike iji ya dị ka GPIO |
4.3 Nwepu
N'akụkụ ala nke osisi ahụ, n'okpuru modul nkwurịta okwu, a na-ahazi akara ngosi debug dị ka 3 × 2 test pads na 100 mil pitch na pin 4 wepụ. A na-egosi pin 1 na eserese 3 - Ọnọdụ njikọ
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | + 3V3 | Nwepu Ike | Mpụta ike emepụtara n'ime ga-eji dị ka voltage ntụaka |
| 2 | SWD | Dijitalụ | nRF52480 Otu data nbipu waya |
| 3 | SWCLK | Digital In | nRF52480 Otu elekere nbipu waya |
| 5 | GND | Ike | Ala Ike |
| 6 | RST | Digital In | Ntinye nrụpụta dị ala na-arụ ọrụ |
| 1 | + 3V3 | Nwepu Ike | Mpụta ike emepụtara n'ime ga-eji dị ka voltage ntụaka |
Ozi igwe
5.1 Ngosipụta bọọdụ na oghere nrịgo
Ngwakọta bọọdụ ahụ na-agwakọta n'etiti metric na imperial. A na-eji ihe ndị eze ukwu na-ejigide grid 100 mil pitch n'etiti ahịrị pin ka ha kwenye ka ha dabara na bọọdụ achịcha ebe ogologo osisi bụ Metric.
Asambodo
6.1 Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
6.2 Nkwuwapụta Nkwekọrịta na EU RoHS & REACH 211 01/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Mwepu: Ọnweghị mpụ a na-ekwu.
Ndị bọọdụ Arduino kwekọrịtara nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi kemịkalụ (REACH). Anyị na-ekwupụta na ọ nweghị nke SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Ndepụta Ndị Candidates nke ihe dị oke elu
Nchegbu maka ikike ikike nke ECHA wepụtara ugbu a dị na ngwaahịa niile (yana ngwungwu) n'ọtụtụ na-agbakọta mkpokọta nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị ihe ọ bụla e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe gbasara nchegbu dị oke elu (SVHC) n'ụdị ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
6.3 Nkwuwapụta mineral na esemokwu
Dị ka onye na-ebubata ngwa elektrọnik na eletrik zuru ụwa ọnụ, Arduino maara ọrụ anyị na-arụ gbasara iwu na ụkpụrụ gbasara Mgbagwoju anya Minerals, kpọmkwem Dodd-Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino anaghị ebute ma ọ bụ hazie esemokwu ozugbo. mineral dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Ngwakọta mineral ndị na-ese okwu dị n'ime ngwaahịa anyị n'ụdị ihe na-ere ahịa, ma ọ bụ dị ka akụrụngwa na alloys ọla. Dị ka akụkụ nke ezigbo mbọ anyị kwesịrị ekwesị, Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere Mineral Conflict sitere na mpaghara enweghị nsogbu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi onye ọrụ.
ikike ịrụ ọrụ akụrụngwa.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
(1) Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
(2) ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20cm n'etiti radiator & ahụ gị.
Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata na ọnọdụ pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụlọ ọrụ mmepụta ihe
Ọkọlọtọ RSS enweghị ikike Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
(1) ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
(2) ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike ibute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 85 ℃ ma ghara ịdị ala karịa -40 ℃.
Site na nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
Ozi ụlọ ọrụ
| Ugboro ugboro | Arduino Srl |
| 863-870Mhz | Site na Andrea Appiani 25 20900 MONZA Italy |
Akwụkwọ ntụaka
| Ntụaka |
Njikọ |
| Arduino IDE (Desktọpụ) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (igwe ojii) | https://create.arduino.cc/editor |
| Cloud IDE na-amalite | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduinoweb-editor-4b3e4a |
| Nzukọ | http://forum.arduino.cc/ |
| SAMD21G18 | http://ww1.microchip.com/downloads/en/devicedoc/40001884a.pdf |
| NINA W102 | https://www.u-blox.com/sites/default/files/N INA-W1O_DataSheet_%28U BX17065507%29.pdf |
| ECC608 | http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf |
| MPM3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
| NINA Firmware | https://github.com/arduino/nina-fw |
| Ụlọ akwụkwọ ECC608 | https://github.com/arduino-libraries/ArduinoECCX08 |
| Ụlọ akwụkwọ LSM6DSL | https://github.com/stm32duino/LSM6DSL |
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ntụaka ụlọ akwụkwọ | https://www.arduino.cc/reference/en/ |
| Ụlọ ahịa Arduino | https://store.arduino.cc/ |
Akụkọ ngbanwe
| Ụbọchị | Ndozigharị | Mgbanwe |
| 04/21/2021 | 1 | Mmelite akwụkwọ data izugbe |
Arduino® Nano 33 BLE
agbanweela: 18/02/2022
Akwụkwọ / akụrụngwa
 |
ARDUINO ABX00030 Nano 33 BLE Miniature Siized Module [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00030, Nano 33 BLE, Module nke pere mpe, Nano 33 BLE Obere nha Module, ABX00030 Nano 33 BLE Miniature Siized Module |
