ARDUINO ABX00031 Nano 33 BLE Sense Module
Tlhaloso
Nano 33 BLE Sense ke mojule oa boholo bo bonyenyane o nang le mojule oa NINA B306, o thehiloeng ho Nordic nRF52480 'me o na le Cortex M4F, crypto chip e ka bolokang li-certificate le linotlolo tse arolelanoang pele le 9 axis IMU. Mojule o ka hlongoa joalo ka karolo ea DIP (ha o kenya lihlooho tsa pin), kapa joalo ka karolo ea SMT, o e kopanya ka kotloloho ka lipampiri tse entsoeng ka masela.
Libaka tse reriloeng:
Moetsi, lintlafatso, ts'ebeliso ea IoT
Likaroloana
NINA B306 Module
processor
- 64 MHz Arm® Cortex-M4F (ka FPU)
- 1 MB Flash + 256 KB RAM
Bluetooth 5 multiprotocol radio
- 2 Mbps
- CSA #2
- Advertising Extensions
- Nako e telele
- +8 dBm TX matla
- -95 dBm kutloisiso
- 4.8 mA ho TX (0 dBm)
- 4.6 mA ho RX (1 Mbps)
- Balun e kopantsoeng e nang le 50 Ω e phethiloeng e le 'ngoe
- IEEE 802.15.4 tšehetso ea seea-le-moea
- Khoele
- Zigbee
Pheripherals
- Lebelo le felletseng la 12 Mbps USB
- NFC-A tag
- Arm CryptoCell CC310 subsystem ts'ireletso QSPI/SPI/TWI/I²S/PDM/QDEC
- Lebelo le phahameng 32 MHz SPI
- Quad SPI interface 32 MHz
- EasyDMA bakeng sa lihokelo tsohle tsa dijithale
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR co-processor
LSM9DS1 (9 axis IMU)
- Likanale tse 3 tsa ho potlakisa, liteishene tse 3 tsa lebelo la li-angular, likanale tse 3 tsa masimo a khoheli
- ± 2 / ± 4 / ± 8 / ± 16 g ho potlakisa lebelo le felletseng
- ± 4 / ± 8 / ± 12 / ± 16 gauss makenete sekala se felletseng
- ± 245 / ± 500 / ± 2000 dps sekhahla sa angular sekala se felletseng
- Tlhahiso ea data ea 16-bit
LPS22HB (Barometer le sensor ea mocheso)
- 260 ho isa ho 1260 hPa khatello e felletseng ea khatello e nang le 24-bit e nepahetseng
- Bokhoni bo phahameng ba khatello ea maikutlo: 20x e felletseng
- Matšeliso a mocheso a kentsoeng
- Tlhahiso ea data ea 16-bit ea mocheso
- 1 Hz ho isa ho 75 Hz sekgahla sa data sitisa mesebetsi: Data Ready, FIFO gs, thresholds pressure
HTS221 (sensor e amanang le mongobo)
- 0-100% mefuta e fapaneng ea mongobo
- Kutlo e phahameng ea rH: 0.004% rH/LSB
- Ho nepahala ha mongobo: ± 3.5% rH, 20 ho +80% rH
- Ho nepahala ha mocheso: ± 0.5 °C,15 ho +40 °C
- Mongobo oa 16-bit le data ea tlhahiso ea mocheso
APDS-9960 (Bohaufi ba Dijithale, Leseli le Ambient, RGB le Sensor ea Boitšisinyo)
- Ambient Light le RGB Color Sensing e nang le lifilthara tse thibelang tsa UV le IR
- Kutlo e phahameng haholo - E loketse ts'ebetso ka mor'a khalase e lefifi
- Proximity Sensing le Ambient light rejection
- Ho Utloisisa Boitšisinyo bo Ratang
MP34DT05 (Maekerofounu ea Dijithale)
- AOP = 122.5 dbSPL
- 64 dB karo-karolelano ea lerata-ho-lerata
- Omnidirectional sensitivity
- -26 dBFS ± 3 dB kutlo
ATECC608A (Crypto Chip)
- Cryptographic co-processor e nang le polokelo e sireletsehileng ea lisebelisoa tsa thepa
- Polokelo e sirelelitsoeng bakeng sa linotlolo tse 16, litifikeiti kapa data
- ECDH: FIPS SP800-56A Elliptic Curve Dilfe-Hellman
- NIST e tloaelehileng ea P256 elliptic curve support
- SHA-256 & HMAC hash ho kenyelletsa le "off-chip context" boloka/tsosolosa
- AES-128 encrypt/decrypt, galois field ikatisetsa GCM
MPM3610 DC-DC
- E laola tlhahiso ea molumotage ho tloha ho 21V ka bonyane ba 65% effciency @minimum load
- Ho feta 85% ho sebetsa hantle @12V
Litaba
- Boto
- Lintlha
- Maemo a Tšebetso a khothalelitsoeng
- Tšebeliso ea Matla
- E sebetsa hapeview
- Board Topology
- processor
- Crypto
- IMU
- Barometer le Sensora ea Mocheso
- Mongobo o Batlang le Mocheso oa Mocheso
- Digital Proximity, Ambient Light, RGB le Gesture Sensor
- Ho lemoha ka boitšisinyo
- Ho lemoha ha haufi
- Ho lemoha 'Mala le ALS
- Microphone ea Digital
- Sefate sa Matla
- Ts'ebetso ea Boto
- Ho qala - IDE
- Ho qala - Arduino Web Mohlophisi
- Ho qala - Arduino IoT Cloud
- Sample Sketches
- Lisebelisoa tsa Marang-rang
- Boto ea Pholiso
- Sehokedi Pinouts
- USB
- Lihlooho
- Hlakola
- Boitsebiso ba Mechini
- Kemiso ea Boto le Likoti tse Homang
- Setifikeiti
- Declaration of Conformity CE DoC (EU)
- Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
- Phatlalatso ea Liminerale ea Khohlano
- FCC Tlhokomeliso
- Lintlha tsa Khampani
- Litokomane Tsa Litšupiso
- Nalane ea Phetoho
Boto
Joalo ka liboto tsohle tsa Nano form factor, Nano 33 BLE Sense ha e na tjhaja ea betri empa e ka tsamaisoa ka USB kapa lihlooho.
HLOKOMELA: Arduino Nano 33 BLE Sense e ts'ehetsa 3.3VI/Os feela 'me HA E mamelle 5V kahoo ka kopo etsa bonnete ba hore ha o hokelle matšoao a 5V ka kotloloho ho boto ena kapa e tla senyeha. Hape, ho fapana le liboto tsa Arduino Nano tse tšehetsang ts'ebetso ea 5V, pinana ea 5V HA E fane ka vol.tage empa ho e-na le hoo e hokahane, ka jumper, ho kenya matla a USB.
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Max |
| Meeli ea mocheso oa Conservative bakeng sa boto kaofela: | -40 °C (40 °F) | 85°C ( 185 °F) |
Tšebeliso ea Matla
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| PBL | Tšebeliso ea matla e nang le loop e phathahaneng | TBC | mW | ||
| PLP | Tšebeliso ea matla ka mokhoa o fokolang oa matla | TBC | mW | ||
| PMAX | Tšebeliso e Felletseng ea Matla | TBC | mW |
E sebetsa hapeview
Board Topology
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U1 | NINA-B306 Module BLE 5.0 Module | U6 | MP2322GQH Step Down Converter |
| U2 | Tlhaloso: LSM9DS1TR IMU | PB1 | IT-1185AP1C-160G-GTR Konopo ea ho sututsa |
| U3 | Maekerofounu ea MP34DT06JTR Mems | HS-1 | Sensor ea mongobo ea HTS221 |
| U4 | ATECC608A Crypto chip | DL1 | Led L |
| U5 | APDS-9660 Ambient Module | DL2 | Matla a Led |
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| SJ1 | VUSB jumper | SJ2 | D7 Jumper |
| SJ3 | 3v3 Jumper | SJ4 | D8 Jumper |
processor
Main processor ke Cortex M4F e sebetsang ho fihla ho 64MHz. Boholo ba lithakhisa tsa eona li hokahane le lihlooho tsa ka ntle, leha ho le joalo, tse ling li boloketsoe puisano ea ka hare le mochine o se nang mohala le li-peripherals tsa I2C tse ka hare (IMU le Crypto).
HLOKOMELA: Ho fapana le liboto tse ling tsa Arduino Nano, lithakhisa A4 le A5 li na le ho hula ka hare 'me li ka sebelisoa e le I2C Bus kahoo ha ho khothalletsoe ho sebelisoa e le lisebelisoa tsa analog.
Crypto
The crypto chip ho liboto tsa Arduino IoT ke eona e etsang phapang le liboto tse ling tse sa sireletsehang kaha e fana ka mokhoa o sireletsehileng oa ho boloka liphiri (joalo ka litifikeiti) le ho potlakisa liprothokholo tse bolokehileng ha ho mohla li senolang liphiri ka mongolo o hlakileng. Khoutu ea mohloli bakeng sa Laeborari ea Arduino e tšehetsang Crypto e fumaneha [8]
IMU
Arduino Nano 33 BLE e na le 9 axis IMU e kenyelelitsoeng e ka sebelisoang ho lekanya mokhoa oa boto (ka ho hlahloba chebahalo ea vector ea matla a khoheli kapa ka ho sebelisa sesupa-tsela sa 3D) kapa ho lekanya litšisinyeho, ho thothomela, ho potlakisa le lebelo la ho potoloha. Khoutu ea mohloli bakeng sa Laeborari ea Arduino e tšehetsang IMU ea fumaneha [9]
Barometer le Sensora ea Mocheso
Barometer e kentsoeng le sensor ea mocheso li lumella ho lekanya khatello ea tikoloho. Sensor ea mocheso e kopantsoeng le barometer e ka sebelisoa ho lefella tekanyo ea khatello. Khoutu ea mohloli bakeng sa Laeborari ea Arduino e tšehetsang Barometer ea fumaneha [10]
Mongobo o Batlang le Mocheso oa Mocheso
Sensor sa mongobo se lekanyetsoang se lekanya mongobo o lekanyelitsoeng. Joaloka Barometer, sensor ena e na le sensor e kopantsoeng ea mocheso e ka sebelisoang ho lefella tekanyo. Khoutu ea mohloli bakeng sa Laeborari ea Arduino e tšehetsang sensor ea mongobo e fumaneha [11]
Digital Proximity, Ambient Light, RGB le Gesture Sensor
Khoutu ea mohloli oa Laeborari ea Arduino e tšehetsang sensor ea Proximity / boitšisinyo / ALS ea fumaneha [12]
Ho lemoha ka boitšisinyo
Ho lemoha ka boitšisinyo ho sebelisa li-photodiode tse 'ne tsa nqa e le ngoe ho utloa matla a IR (a tsoang ho LED e kopaneng) ho fetolela fisiks.
Ho lemoha ha haufi
Karolo ea ho lemoha ha Proximity e fana ka tekanyo ea sebaka (Mohlala, skrine ea sesebelisoa sa mohala ho ea tsebeng ea mosebelisi) ka tlhahlobo ea photodiode ea ref.
Ho lemoha 'Mala le ALS
Karolo ea ho lemoha Mebala le ALS e fana ka lintlha tse khubelu, tse tala, tse putsoa le tse hlakileng. E 'ngoe le e 'ngoe ea likanale tsa R, G, B, C e na le U
Microphone ea Digital
MP34DT05 ke maekerofounu ea ultra-compact, matla a tlase, a omnidirectional, a digital MEMS e hahiloeng ka karolo ea capacitive sensing le sebopeho sa IC. Sensing element, e khonang ho bona maqhubu a acoustic, e etsoa ka mokhoa o ikhethileng oa silicon micromachining o ikemiselitseng ho hlahisa li-audio sensors.
Sefate sa Matla
Boto e ka tsamaisoa ka sehokelo sa USB, VIN kapa VUSB lithareng.
HLOKOMELA: Kaha VUSB e fepa VIN ka diode ea Schottky le molaoli oa DC-DC o boletse bonyane matla a ho kenya.tage ke 4.5V bonyane ba phepelo ea matlatage ho tloha ho USB e tlameha ho eketseha ho ea ho voltage sebakeng se pakeng tsa 4.8V le 4.96V ho itšetlehile ka se huloang hona joale.
Ts'ebetso ea Boto
Ho qala - IDE
Haeba u batla ho kenya Arduino Nano 33 BLE ea hau ha u ntse u le sieo, u lokela ho kenya Arduino Desktop IDE [1] Ho hokela Arduino Nano 33 BLE komporong ea hau, u tla hloka thapo ea USB ea Micro-B. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
Ho qala - Arduino Web Mohlophisi
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose la Arduino Web Mohlophisi [2], ka ho kenya plugin e bonolo feela. The Arduino Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau.
Ho qala - Arduino IoT Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino IoT li tšehetsoa ho Arduino IoT Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
Sample Sketches
Sample litšoantšo tsa Arduino Nano 33 BLE li ka fumanoa ho "Examples" ho Arduino IDE kapa karolong ea "Documentation" ea Arduino Pro websebaka [4]
Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho ProjectHub [13], Arduino Library Reference [14] le lebenkele la marang-rang [15] moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling.
Boto ea Pholiso
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho khantša boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khoneha ho kenya mokhoa oa bootloader ka ho tlanya habeli konopo ea reset hang ka mor'a ho tima.
Sehokedi Pinouts
USB
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | VUSB | Matla | Phepelo ea Matla. Haeba boto e tsamaisoa ka VUSB ho tloha hloohong sena ke Output (1) |
| 2 | D- | Tse fapaneng | Lintlha tse fapaneng tsa USB - |
| 3 | D+ | Tse fapaneng | Lintlha tse fapaneng tsa USB + |
| 4 | ID | Analoge | E khetha tšebetso ea Host/Device |
| 5 | GND | Matla | Sebaka sa Matla |
Lihlooho
Boto e pepesa lihokelo tse peli tsa phini tse 15 tse ka bokelloang ka lihlooho tsa phini kapa tsa rekisoa ka li-vias tse khabisitsoeng.
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D13 | Dijithale | GPIO |
| 2 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare ho lisebelisoa tsa kantle |
| 3 | AREF | Analoge | Tlhaloso ea Analog; e ka sebelisoa e le GPIO |
| 4 | A0/DAC0 | Analoge | ADC in/DAC tsoa; e ka sebelisoa e le GPIO |
| 5 | A1 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 6 | A2 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 7 | A3 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 8 | A4/SDA | Analoge | ADC ka; I2C SDA; E ka sebelisoa e le GPIO (1) |
| 9 | A5/SCL | Analoge | ADC ka; I2C SCL; E ka sebelisoa e le GPIO (1) |
| 10 | A6 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 11 | A7 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 12 | VUSB | Matla ka hare/Kantle | Ka tloaelo NC; e ka hokela ho VUSB phini ea sehokelo sa USB ka ho khutsufatsa jumper |
| 13 | RST | Digital In | Kenyo e sebetsang e tlase ea ho seta bocha (kopi ea phini ea 18) |
| 14 | GND | Matla | Sebaka sa Matla |
| 15 | VIN | Power In | Ho kenya Matla a Vin |
| 16 | TX | Dijithale | UART TX; e ka sebelisoa e le GPIO |
| 17 | RX | Dijithale | UART RX; e ka sebelisoa e le GPIO |
| 18 | RST | Dijithale | Kenyo e sebetsang e tlase ea ho seta bocha (kopi ea phini ea 13) |
| 19 | GND | Matla | Sebaka sa Matla |
| 20 | D2 | Dijithale | GPIO |
| 21 | D3/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 22 | D4 | Dijithale | GPIO |
| 23 | D5/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 24 | D6/PWM | Dijithale | GPIO, e ka sebelisoa e le PWM |
| 25 | D7 | Dijithale | GPIO |
| 26 | D8 | Dijithale | GPIO |
| 27 | D9/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 28 | D10/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 29 | D11/MOSI | Dijithale | SPI MOSI; e ka sebelisoa e le GPIO |
| 30 | D12/MISO | Dijithale | SPI MISO; e ka sebelisoa e le GPIO |
Hlakola
Ka lehlakoreng le ka tlase la boto, tlas'a mojule oa puisano, matšoao a debug a hlophisitsoe joalo ka lipampiri tsa liteko tsa 3 × 2 tse nang le 100 mil pitch e nang le pin 4 e tlositsoeng. Pin 1 e bonts'itsoe ho Setšoantšo sa 3 - Maemo a Sehokelo
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare a tla sebelisoa e le voltage referense |
| 2 | SWD | Dijithale | nRF52480 data ea Single Wire Debug |
| 3 | SWCLK | Digital In | nRF52480 Single Wire Debug Clock |
| 5 | GND | Matla | Sebaka sa Matla |
| 6 | RST | Digital In | Kenyo e sebetsang e tlase ea ho seta bocha |
Boitsebiso ba Mechini
Kemiso ea Boto le Likoti tse Homang
Mehato ea boto e tsoakane pakeng tsa metric le imperial. Mehato ea borena e sebelisoa ho boloka 100 mil pitch grid pakeng tsa mela ea phini ho ba lumella ho lekana le boardboard athe bolelele ba boto ke Metric.
Setifikeiti
Declaration of Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Bolelele ba moeli (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokoloho: Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse hore ha ho le e 'ngoe ea SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Lethathamo la Bakhethoa ba Matšoenyeho a Holimo Haholo bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoang tsohle (le sephutheloana) ka bongata bo boholo bo lekanang kapa bo kaholimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha e boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa lisebelisoa tsa elektroniki le tsa motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e amanang le Conflict Minerals, haholoholo Dodd-Frank Wall Street Reform and Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise kapa ha e sebetsane le likhohlano ka kotloloho. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tse loantšanang li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ba ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho ipapisitsoe le tlhaiso-leseling eo re e fumaneng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Conflict tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa. Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- thepa ea hae e lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Thepa ena e lokela ho kengoa le ho sebetsoa ka sebaka sa bonyane 20cm lipakeng tsa radiator le 'mele oa hau.
Sesotho: Libukana tsa mosebelisi bakeng sa lisebelisoa tsa radio tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang sebakeng se hlakileng bukeng ea mosebelisi kapa sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa RSS tse sa dumelleng laesense ya Industry Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Sesotho Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka se bonyane 20 cm pakeng tsa radiator le 'mele oa hau. Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
| Maqhubu a maqhubu | Matla a phahameng haholo (ERP) |
| 863-870Mhz | 5.47dBm |
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino Srl |
| Aterese ea Khampani | Via Andrea Appiani 25 20900 MONZA Italy |
Litokomane Tsa Litšupiso
| Referense | Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Leru) | https://create.arduino.cc/editor |
| Cloud IDE Ho qala | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor-4b3e4a |
| Foramo | http://forum.arduino.cc/ |
| Kena B306 | https://www.u-blox.com/sites/default/files/NINA-B3_DataSheet_%28UBX-17052099%29.pdf |
| EA-608-EF | http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf |
| MPM3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
| Laebrari ea ECC608 | https://github.com/arduino-libraries/ArduinoECCX08 |
| Laeborari ea LSM6DSL | https://github.com/adafruit/Adafruit_LSM9DS1 |
| LPS22HB | https://github.com/stm32duino/LPS22HB |
| Laeborari ea HTS221 | https://github.com/stm32duino/HTS221 |
| Laebrari ea APDS9960 | https://github.com/adafruit/Adafruit_APDS9960 |
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://www.arduino.cc/reference/en/ |
Nalane ea Phetoho
| Letsatsi | Khatiso | Liphetoho |
| 04/27/2021 | 1 | Lintlafatso tse akaretsang tsa database |
Litokomane / Lisebelisoa
 |
ARDUINO ABX00031 Nano 33 BLE Sense Module [pdf] Bukana ea Mosebelisi ABX00031, Nano 33 BLE Sense, Module, Nano 33 BLE Sense Module, ABX00031 Nano 33 BLE Sense Module |
