Arduino® Nano 33 BLE
Khoom Siv Taw Qhia
SKU: ABX00030
Kev piav qhia
Nano 33 BLE yog cov qauv me me uas muaj NINA B306 module, raws li Nordic nRF52480 thiab muaj Cortex M4F thiab 9-axis IMU. Lub module tuaj yeem raug mounted li DIP tivthaiv (thaum mounting tus pin headers) los yog raws li ib tug SMT tivthaiv, ncaj qha soldering nws ntawm lub castellated pads.
Lub hom phiaj thaj chaw:
Tus tsim, txhim kho, yooj yim IoT daim ntawv thov scenarios
Nta
- NINA B306 Module
- Processor
- 64 MHz Arm® Cortex-M4F (nrog FPU)
- 1 MB Flash + 256 KB RAM
- Bluetooth 5 multiprotocol xov tooj cua
- 2 Mbps
- CSA #2
- Tshaj tawm Extensions
- Ntev Ntev
- + 8 dBm TX
- -95 dBm rhiab heev
- 4.8 mA in TX (0 dBm)
- 4.6 mA hauv RX (1 Mbps)
- Integrated balun nrog 50 Ω ib leeg-kawg tso zis
- IEEE 802.15.4 xov tooj cua txhawb nqa
- Xov
- Zigbee
- Processor
- Peripherals
- Full-ceev 12 Mbps USB
- NFC-A tag
- Arm CryptoCell CC310 kev ruaj ntseg subsystem
- QSPI/SPI/TWI/I²S/PDM/QDEC
- Kev kub ceev 32 MHz SPI
- Quad SPI interface 32 MHz
- EasyDMA rau tag nrho cov digital interfaces
- 12-ntsis 200 ksps ADC
- 128 ntsis AES/ECB/CCM/AAR co-processor
- LSM9DS 1 (9 axis IMU)
- 3 acceleration channels, 3 angular rate channels, 3 magnetic fields
- ± 2 / ± 4 / ± 8 / ± 16 g linear acceleration tag nrho teev
- ± 4 / ± 8 / ± 12 / ± 16 gauss magnetic tag nrho teev
- ± 245 / ± 500 / ± 2000 dps angular tus nqi tag nrho
- 16-ntsis cov ntaub ntawv tso zis - MPM 3610 DC-DC
- Regulates input voltage los ntawm mus txog 21V nrog yam tsawg kawg nkaus ntawm 65% fficiency @ yam tsawg kawg nkaus load
- Ntau tshaj 85% fficiency @ 12V
Lub Rooj Tswjhwm Saib
Zoo li txhua tus Nano daim ntawv boards, Nano 33 BLE tsis muaj lub roj teeb charger tab sis tuaj yeem siv tau los ntawm USB lossis headers.
CEEB TOOM: Arduino Nano 33 BLE tsuas yog txhawb nqa 3.3VI/Os thiab tsis yog 5V ua siab ntev yog li thov xyuas kom koj tsis ncaj qha txuas 5V teeb liab rau lub rooj tsavxwm no lossis nws yuav raug puas tsuaj. Tsis tas li ntawd, tsis zoo li Arduino Nano boards uas txhawb nqa 5V kev ua haujlwm, 5V tus pin tsis muab vol.tage tab sis zoo txuas nrog, los ntawm lub jumper, mus rau USB lub zog nkag.
Daim ntawv thov Examples
Suab spectrum: Tsim ib lub suab spectrum kom pom cov suab zaus. Txuas lub Arduino 33 Nano BLE thiab lub microphone los yog ampli -ib.
Social Distancing Sensor: Ua kom muaj kev sib raug zoo nyob deb tau dhau los ua qhov tseem ceeb dua li yav dhau los los ua kom koj tus kheej, nrog rau lwm tus kev noj qab haus huv. Los ntawm kev sib txuas ntawm Arduino Nano 33 BLE nrog lub sensor thiab LED zaub, koj tuaj yeem tsim ib lub tsho hnav uas ceeb toom koj thaum koj nyob ze rau lwm tus neeg.
Healthy plant scanner: Kev ywg dej koj cov nroj tsuag tsis yog ib txwm txaus kom lawv zoo siab. Kab mob, tsis muaj hnub ci, thiab lwm yam tuaj yeem yog qhov tseem ceeb rau cov nroj tsuag tsis zoo. Ua kom koj cov nroj tsuag zoo siab los ntawm kev tsim lub tshuab ntes thiab cob qhia nws txhawm rau txheeb xyuas txhua yam kab mob, tag nrho nrog Arduino Nano 33 BLE
Kev ntsuas
Pom zoo rau kev ua haujlwm
| Cim | Kev piav qhia | Min | Max |
| Conservative thermal txwv rau tag nrho lub rooj tsavxwm: | -40 ° C (40 ° F) | 85 ° C (185 ° F) |
Kev siv fais fab
| Cim | Kev piav qhia | Min | Ntaus | Max | Chav tsev |
| PBL | Kev siv lub zog nrog lub voj tsis khoom | TBC | mW | ||
| PLP | Kev siv hluav taws xob hauv hom qis zog | TBC | mW | ||
| PMAX | Kev siv hluav taws xob siab tshaj plaws | TBC | mW |
Muaj nuj nqi Tshajview
Board Topology
Board topology Sab saum toj
| Ref. | Kev piav qhia | Ref. | Kev piav qhia |
| U1 | NINA-B306 Module BLE 5.0 Module | U6 | MP2322GQH Kauj ruam Down Converter |
| U2 | LSM9DS1TR Sensor IMU | PB 1 | IT-1185AP1C-160G-GTR Push khawm |
| DL1 | Coj L | DL2 | Led zog |
Hauv qab:
Board topology bot
| Ref. | Kev piav qhia | Ref. | Kev piav qhia |
| SJ 1 | VUSB Jumper | SJ 2 | D7 Jumper |
| SJ 3 | 3v3 pom | SJ 4 | D8 Jumper |
Processor
Tus Txheej Txheem Tseem Ceeb yog Cortex M4F khiav mus txog 64MHz. Feem ntau ntawm nws cov pins txuas nrog cov headers sab nraud, txawm li cas los xij, qee qhov tau tshwj tseg rau kev sib txuas lus sab hauv nrog lub wireless module thiab on-board sab hauv I²C peripherals (IMU thiab Crypto).
CEEB TOOM: Raws li kev tawm tsam rau lwm cov Arduino Nano boards, pins A4 thiab A5 muaj kev rub tawm sab hauv thiab lub neej ntawd yuav tsum tau siv los ua I²C Bus yog li siv los ua analog inputs tsis pom zoo.
Tsob Ntoo Tsob Ntoo
Lub rooj tsavxwm tuaj yeem siv tau los ntawm USB connector, VIN, lossis VUSB pins ntawm headers.
Tsob ntoo muaj zog
CEEB TOOM: Txij li thaum VUSB pub VIN ntawm Schottky diode thiab DC-DC regulator tshwj xeeb yam tsawg kawg nkaus input vol.tage yog 4.5V qhov tsawg kawg nkaus mov voltage los ntawm USB yuav tsum tau nce mus rau voltage nyob rau hauv qhov ntau ntawm 4.8V txog 4.96V nyob ntawm qhov tam sim no raug kos.
Board ua haujlwm
3.1 Tau Txais - IDE
Yog tias koj xav ua haujlwm rau koj lub Arduino Nano 33 BLE thaum lub sijhawm koj yuav tsum tau nruab Arduino Desktop IDE [1] Txhawm rau txuas Arduino Nano 33 BLE rau koj lub computer, koj yuav xav tau Micro-B USB cable. Qhov no tseem muab lub zog rau lub rooj tsavxwm, raws li qhia los ntawm LED.
3.2 Tau Txais - Arduino Web Editor
Txhua Arduino boards, suav nrog qhov no, ua haujlwm tawm ntawm lub thawv ntawm Arduino Web Editor [2], los ntawm kev txhim kho ib qho yooj yim plugin.
Lub Arduino Web Editor yog hosted hauv online, yog li nws yuav ib txwm hloov tshiab nrog cov yam ntxwv tshiab thiab kev txhawb nqa rau txhua lub rooj tsavxwm. Ua raws li [3] pib coding ntawm browser thiab upload koj cov duab kos rau hauv koj lub rooj tsavxwm.
3.3 Pib Pib - Arduino IoT Huab
Txhua yam khoom siv Arduino IoT tau txais kev txhawb nqa ntawm Arduino IoT Cloud uas tso cai rau koj nkag mus, teeb duab, thiab tshuaj xyuas cov ntaub ntawv sensor, ua rau cov xwm txheej thiab ua kom koj lub tsev lossis kev lag luam.
3.4 Sampua Sketch
Sample sketches rau Arduino Nano 33 BLE tuaj yeem pom nyob rau hauv "Examples” zaub mov hauv Arduino IDE lossis hauv ntu “Cov ntaub ntawv” ntawm Arduino Pro website [4]
3.5 Cov ntaub ntawv online
Tam sim no koj tau dhau los ntawm cov hauv paus ntawm qhov koj tuaj yeem ua nrog lub rooj tsavxwm koj tuaj yeem tshawb nrhiav qhov tsis muaj qhov kawg uas nws muab los ntawm kev tshuaj xyuas cov haujlwm zoo siab ntawm ProjectHub [5], Arduino Library Reference [6], thiab lub khw hauv online [7] qhov twg Koj tuaj yeem ua kom tiav koj lub rooj tsavxwm nrog sensors, actuators thiab ntau dua
3.6 Board Rov qab
Tag nrho cov Arduino boards muaj ib tug built-in bootloader uas tso cai rau flashing lub rooj tsavxwm ntawm USB. Nyob rau hauv cov ntaub ntawv ib tug sketch locks li processor thiab lub rooj tsavxwm tsis ncav cuag tau lawm ntawm USB nws muaj peev xwm mus nkag rau hauv bootloader hom los ntawm ob-tapping lub khawm pib dua tom qab lub hwj chim-up.
Txuas Pinouts
4.1 USB
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | VUSB | Hwj chim | Fais fab mov Input. Yog hais tias lub rooj tsavxwm yog powered ntawm VUSB los ntawm header qhov no yog ib qho Output 1 |
| 2 | D- | Qhov txawv | USB cov ntaub ntawv sib txawv - |
| 3 | D+ | Qhov txawv | USB cov ntaub ntawv sib txawv + |
| 4 | ID | Analog | Xaiv lub party/Device functionality |
| 5 | GND | Hwj chim | Hwj chim hauv av |
4.2 Headers
Lub rooj tsavxwm nthuav tawm ob lub 15-pin connectors uas tuaj yeem ua ke nrog tus pin headers lossis soldered los ntawm castellated vias.
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | D13 | Digital | GPIO |
| 2 | +3V 3 | Hwj chim Tawm | Internally generated hwj chim tso zis rau lwm pab kiag li lawm |
| 3 | AREF | Analog | Analog siv; tuaj yeem siv ua GPIO |
| 4 | A0/DAC0 | Analog | ADC hauv / DAC tawm; tuaj yeem siv ua GPIO |
| 5 | A1 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 6 | A2 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 7 | A3 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 8 | A4/SDA | Analog | ADC hauv; I2C SDA; Yuav siv tau raws li GPIO (1) |
| 9 | A5 / SCL | Analog | ADC hauv; I2C SCL; Yuav siv tau raws li GPIO (1) |
| 10 | A6 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 11 | A7 | Analog | ADC hauv; tuaj yeem siv ua GPIO |
| 12 | VUSB | Fais fab hauv / tawm | Nquag NC; tuaj yeem txuas nrog VUSB tus pin ntawm USB connector los ntawm shorting a |
| 13 | RST | Digital Hauv | Lub active-low reset input (duab ntawm tus pin 18) |
| 14 | GND | Hwj chim | Hwj chim hauv av |
| 15 | VIN | Fais fab hauv | Vin Power input |
| 16 | TX | Digital | USART TX; tuaj yeem siv ua GPIO |
| 17 | RX | Digital | USART RX; tuaj yeem siv ua GPIO |
| 18 | RST | Digital | Lub active-low reset input (duab ntawm tus pin 13) |
| 19 | GND | Hwj chim | Hwj chim hauv av |
| 20 | D2 | Digital | GPIO |
| 21 | D3/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 22 | D4 | Digital | GPIO |
| 23 | D5/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 24 | D6/PWM | Digital | GPIO tuaj yeem siv ua PWM |
| 25 | D7 | Digital | GPIO |
| 26 | D8 | Digital | GPIO |
| 27 | D9/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 28 | D10/PWM | Digital | GPIO; tuaj yeem siv ua PWM |
| 29 | D11/MOSI | Digital | SPI MOSI; tuaj yeem siv ua GPIO |
| 30 | D12/MISO | Digital | SPI MISO; tuaj yeem siv ua GPIO |
4.3 Debug
Nyob rau sab hauv qab ntawm lub rooj tsavxwm, nyob rau hauv kev sib txuas lus module, debug signals yog teem raws li 3 × 2 xeem pads nrog 100 mil suab nrog tus pin 4 tshem tawm. Pin 1 yog piav nyob rau hauv daim duab 3 - Connector Positions
| Pin | Muaj nuj nqi | Hom | Kev piav qhia |
| 1 | +3V 3 | Hwj chim Tawm | Internally generated hwj chim tso zis yuav siv tau raws li ib tug voltage siv |
| 2 | SWD | Digital | nRF52480 Ib Wire Debug Data |
| 3 | SWCLK | Digital Hauv | nRF52480 Tib Hlau Debug Clock |
| 5 | GND | Hwj chim | Hwj chim hauv av |
| 6 | RST | Digital Hauv | Active low reset input |
| 1 | +3V 3 | Hwj chim Tawm | Internally generated hwj chim tso zis yuav siv tau raws li ib tug voltage siv |
Cov ntaub ntawv siv tshuab
5.1 Board Outline thiab Mounting Qhov
Lub rooj tsavxwm ntsuas yog sib xyaw ntawm metric thiab imperial. Imperial ntsuas yog siv los tswj 100 mil pitch grid nruab nrab ntawm tus pin kab kom tso cai rau lawv kom haum lub breadboard whereas board length yog Metric
Cov ntawv pov thawj
6.1 Kev Tshaj Tawm Txog Kev Ua Raws Cai CE DoC (EU)
Peb tshaj tawm raws li peb lub luag haujlwm ib leeg tias cov khoom lag luam saum toj no tau ua raws li cov cai tseem ceeb ntawm EU Cov Lus Qhia hauv qab no thiab yog li tsim nyog rau kev txav mus los dawb hauv kev lag luam suav nrog European Union (EU) thiab European Economic Area (EEA).
6.2 Kev Tshaj Tawm Txog Kev Ua Raws Li EU RoHS & REACH 211 01/19/2021
Arduino boards tau ua raws li RoHS 2 Directive 2011/65 / EU ntawm European Parliament thiab RoHS 3 Cov Lus Qhia 2015/863 / EU ntawm Pawg Sab Laj ntawm 4 Lub Rau Hli 2015 ntawm kev txwv tsis pub siv qee yam khoom siv phom sij hauv cov khoom siv hluav taws xob thiab hluav taws xob.
| Tshuaj | Qhov siab tshaj plaws (ppm) |
| Lead (Pb) Hmoob. | 1000 |
| Cadmium (Cd) | 100 |
| Mercury (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Tom ntej: Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl) phthalate (DEHP) | 1000 |
| Tom ntej: Benzyl Butyl Phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Kev zam: Tsis muaj kev zam.
Arduino Boards tau ua raws li tag nrho cov kev cai ntawm European Union Regulation (EC) 1907 / 2006 hais txog Kev Sau Npe, Kev Ntsuam Xyuas, Kev Tso Cai, thiab Kev Txwv Cov Tshuaj (REACH). Peb tshaj tawm tsis muaj SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Daim Ntawv Teev Npe ntawm Cov Khoom Siv Siab heev
Kev txhawj xeeb rau kev tso cai tam sim no tso tawm los ntawm ECHA yog tam sim no nyob rau hauv tag nrho cov khoom (thiab tej pob khoom) nyob rau hauv kom muaj nuj nqis tag nrho ib tug concentration sib npaug zos rau los yog siab tshaj 0.1%. Rau qhov zoo tshaj plaws ntawm peb txoj kev paub, peb kuj tshaj tawm tias peb cov khoom tsis muaj ib yam ntawm cov khoom muaj npe nyob rau hauv "Daim Ntawv Tso Cai" (Annex XIV ntawm REACH cov cai) thiab Cov Khoom Muaj Kev Txaus Siab Siab (SVHC) hauv ib qho tseem ceeb npaum li qhov tau hais tseg. los ntawm Annex XVII ntawm Cov Neeg Sib Tw Cov Npe Tshaj Tawm los ntawm ECHA (European Chemical Agency) 1907/2006/EC.
6.3 Cov lus tshaj tawm tsis sib haum xeeb
Raws li lub ntiaj teb kev lag luam ntawm cov khoom siv hluav taws xob thiab hluav taws xob, Arduino paub txog peb lub luag haujlwm hais txog kev cai lij choj thiab cov cai hais txog kev tsis sib haum xeeb Minerals, tshwj xeeb yog Dodd-Frank Wall Street Reform and Consumer Protection Act, Section 1502. Arduino tsis ncaj qha los yog txheej txheem teeb meem. minerals xws li Tin, Tantalum, Tungsten, los yog kub. Cov zaub mov tsis sib haum xeeb yog muaj nyob rau hauv peb cov khoom nyob rau hauv daim ntawv ntawm solder, los yog raws li ib feem ntawm cov hlau alloys. Raws li ib feem ntawm peb qhov kev mob siab rau tsim nyog, Arduino tau hu xov tooj rau cov khoom lag luam hauv peb cov khoom siv los txheeb xyuas lawv txuas ntxiv ua raws li cov cai. Raws li cov ntaub ntawv tau txais tam sim no peb tshaj tawm tias peb cov khoom muaj cov khoom tsis sib haum xeeb tau los ntawm thaj chaw tsis sib haum xeeb.
FCC ceev faj
Ib qho kev hloov pauv lossis kev hloov kho uas tsis tau pom zoo los ntawm pawg neeg saib xyuas kev ua raws cai tuaj yeem cuam tshuam tus neeg siv
txoj cai los khiav cov khoom siv.
Cov cuab yeej no ua raws li Tshooj 15 ntawm FCC Cov Cai. Kev ua haujlwm yog ua raws li ob yam hauv qab no:
(1) Cov cuab yeej no yuav tsis ua rau muaj teeb meem cuam tshuam
(2) cov cuab yeej no yuav tsum lees txais txhua qhov cuam tshuam tau txais, suav nrog kev cuam tshuam uas yuav ua rau tsis xav ua haujlwm.
FCC RF Radiation Exposure Statement:
- Lub Transmitter no yuav tsum tsis txhob muab tso rau hauv los yog ua haujlwm ua ke nrog lwm tus kav hlau txais xov lossis cov khoom xa tawm.
- Cov cuab yeej no ua raws li cov kev txwv ntawm RF hluav taws xob raug teeb tsa rau qhov chaw tsis muaj kev tswj hwm.
- Cov cuab yeej no yuav tsum tau nruab thiab ua haujlwm nrog qhov tsawg kawg nkaus ntawm 20cm ntawm lub tshuab hluav taws xob thiab koj lub cev.
Cov neeg siv phau ntawv rau cov khoom siv xov tooj cua tsis muaj ntawv tso cai yuav tsum muaj cov ntawv ceeb toom hauv qab no lossis sib npaug hauv qhov chaw pom tseeb hauv phau ntawv siv los yog hloov ntawm lub cuab yeej lossis ob qho tib si. Cov cuab yeej no ua raws li Kev Lag Luam
Canada daim ntawv tso cai-exemt RSS standard(s). Kev ua haujlwm yog ua raws li ob yam hauv qab no:
(1) cov cuab yeej no yuav tsis ua rau cuam tshuam
(2) cov cuab yeej no yuav tsum lees txais kev cuam tshuam, suav nrog kev cuam tshuam uas yuav ua rau lub cuab yeej tsis xav tau ua haujlwm.
IC SAR Ceeb toom:
Cov cuab yeej no yuav tsum tau nruab thiab ua haujlwm nrog qhov tsawg kawg nkaus ntawm 20 cm ntawm lub tshuab hluav taws xob thiab koj lub cev.
Tseem ceeb: Kev ua haujlwm kub ntawm EUT tsis tuaj yeem siab tshaj 85 ℃ thiab yuav tsum tsis txhob qis dua -40 ℃.
Ntawm no, Arduino Srl tshaj tawm tias cov khoom no yog ua raws li cov cai tseem ceeb thiab lwm yam kev cai ntawm Cov Lus Qhia 2014/53/EU. Cov khoom no raug tso cai siv nyob rau hauv tag nrho EU cov tswv cuab lub xeev.
Cov ntaub ntawv tuam txhab
| Ntau zaus | Arduino Srl |
| 863-870 MHz | Ntawm Andrea Appiani 25 20900 MONZA Ltalis |
Cov ntaub ntawv siv
| Kev siv |
Txuas |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Huab) | https://create.arduino.cc/editor |
| Cloud IDE Pib Pib | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduinoweb-editor-4b3e4a |
| Rooj sab laj | http://forum.arduino.cc/ |
| TIAB SA 21G18 | http://ww1.microchip.com/downloads/en/devicedoc/40001884a.pdf |
| NIAS W102 | https://www.u-blox.com/sites/default/files/N INA-W1O_DataSheet_%28U BX17065507%29.pdf |
| EC608 | http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf |
| MPM 3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
| NINA Firmware | https://github.com/arduino/nina-fw |
| Lub tsev qiv ntawv ECC608 | https://github.com/arduino-libraries/ArduinoECCX08 |
| LSM6DSL Library | https://github.com/stm32duino/LSM6DSL |
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Library Reference | https://www.arduino.cc/reference/en/ |
| Arduino Khw | https://store.arduino.cc/ |
Kev kho keeb kwm
| Hnub tim | Kev kho dua | Hloov |
| 04/21/2021 | 1 | General datasheet hloov tshiab |
Arduino® Nano 33 BLE
Hloov kho: 18/02/2022
Cov ntaub ntawv / Cov ntaub ntawv
 |
ARDUINO ABX00030 Nano 33 BLE Miniature Me Me Module [ua pdf] Tus neeg siv phau ntawv ABX00030 Nano 33 BLE Nano 33 BLE Miniature Me Me Module ABX00030 Nano 33 BLE Cov Me Me Me Module |
