Letoto le phahameng la FDV
Phepelo ea motlakase o le mong
Access Power Controllers (PTC)
Tataiso ea ho Kena

Maximal7FDV Access Power Controllers

Mefuta e kenyeletsa:
Boholo ba 3FDV
– 12VDC @ 4.6A kapa 24VDC @ 5.2A.
– Leshome le metso e tsheletseng (16) PTC e sireleditsweng dipoelo.
Boholo ba 5FDV
– 12VDC @ 8.6A.
– Leshome le metso e tsheletseng (16) PTC e sireleditsweng dipoelo.
Boholo ba 7FDV
– 24VDC @ 9.2A.
– Leshome le metso e tsheletseng (16) PTC e sireleditsweng dipoelo.

Setšoantšo sa SFDV031115
Khampani ea ho kenya: _______________
Lebitso la Moemeli oa Tšebeletso: _______________
Aterese: ________________________
Nomoro ea mohala: _______________________

MaximalFDV Series Overview:

Altronix MaximalFDV Access Power / Controlers e aba le ho fetola matla ho fihlella lisebelisoa tsa taolo le lisebelisoa. Ba fetola 220VAC (mofuta o sebetsang oa 198VAC - 256VAC), tlhahiso ea 50 / 60Hz ho tse leshome le metso e tšeletseng (16) tse laoloang ka boithaopo tse 12VDC kapa 24VDC PTC tse sirelelitsoeng. Liphello li kenngoa ts'ebetsong ke sink e bulehileng ea pokello kapa ka tloaelo e bulehileng (NO) ho kenya letsoho le omileng ho tloha ho Access Control System, Keypad, Push Button, REX PIR, joalo-joalo Li-Units li tla tsamaisa matla ho lisebelisoa tse fapaneng tsa ho laola lisebelisoa tse kenyeletsang: Mag Locks. , Ho Otloa ha Motlakase, Magnetic Door Holders, joalo-joalo FaCP Interface e nolofalletsa Emergency Egress, Alarm Monitoring, kapa e ka sebelisoa ho qalisa lisebelisoa tse ling tse thusang. Karolo ea ho khaola alamo ea mollo e ka khethoa ka bomong bakeng sa liphetho tsohle kapa tse leshome le metso e tšeletseng (16).

MaximalFDV Series Configuration Chart:

Li-unit tsena li loketse matla: li-sensor, lisebelisoa tsa elektro-mechanical (mohlala, ho otla ha mamati a motlakase).

MaximalFDV Series Features:

ACM8CB Access Controller Modules:

• Ba leshome le metso e ts'eletseng (16) ba ikemela ba hlahisa liphetho tse laoloang. Likhetho tsa tlhahiso:
  a) Tse leshome le metso e ts'eletseng (16) tse feliloeng tsa matla a feliloeng.
  b) Tse leshome le metso e ts'eletseng (16) tse hlahisang matla a feliloeng-Sefe.
  c) Kopanyo efe kapa efe ea tse kaholimo.
• Leshome le metso e ts'eletseng (16) Sistimi ea Taolo ea Phihlello e kenya tse kenang. Likhetho tsa ho kenya letsoho:
  a) Tse leshome le metso e ts'eletseng (16) tse atisang ho buloa (NO) li-trigger tse omileng.
  b) Tse leshome le metso e ts'eletseng (16) tse kenyang likoleke tse bulehileng.
  c) Kopanyo efe kapa efe ea tse kaholimo.
• Leshome le metso e ts'eletseng (16) le sa fetoheng le sefiloeng. lihlahisoa tsa matla (lihlahisoa li lekantsoe @ 2.5A).
• Li-LED tse khubelu ho boto ea ACM8CB li bonts'a hore liphetho tsa motho ka mong lia hlahisoa (li-relay li matlafalitsoe).
• Ho khaoha ha Alarm ea Mollo (ho latching kapa ho se lache) ho ka khethoa ka bonngoe bakeng sa liphetho tse leshome le metso e tšeletseng (16).
  Likhetho tsa ho kenya Alarm ea Mollo:
  a) Ka tloaelo bula (NO) kapa ka tloaelo koaloa (NC) dry trigger input.
  b) Kenyelletso ea ho khutlisetsa polarity ho tsoa ho potoloho ea matšoao a FACP.
• LED e tala ho boto ea ACM8CB e bonts'a hore ho khaoha ha FACP ho qalile.
• Phatlalatso ea FACP e bonts'a hore tlhahiso ea FACP e qalile (foromo ea "C" ea lebitso e rated @ 1A/28VDC).
• Boto ea eFlow Power Supply/Charger e fana ka matla a tšoanang bakeng sa liboto tsa ACM8CB Access Power Controller (lithapo tsa fektheri) le lisebelisoa tsohle tse hokahaneng tsa taolo ea phihlello ( wiring ea tšimo).
• Li-fuse tsa mantlha tsa boto ea ACM8CB li lekantsoe @ 10A. Li-PTC tse hlahisoang li fuoe lintlha tse @ 2.5A.

EFlow Power Supply/Charger:

• Kenyelletso: 220VAC (mofuta o sebetsang oa 198VAC - 256VAC), 50/60Hz.
• Bakeng sa tlhahiso voltage le phepelo ea hajoale e lebisa ho MaximalFDV letoto la Configuration Chart, pg. 3.
• Sephetho sa tlatsetso se reiloe @ 1A (ha sea fetoha).
• Ho tlolatage Tshireletso.
• Tjhaja e hahelletsoeng kahare bakeng sa asiti e tiisitsoeng ea lead kapa libeteri tsa mofuta oa gel
• Boholo ba tefiso ea hajoale ke 1.54A.
• Jarolla ka ho iketsa ho ea stand-by betri ha AC hloleha.
  Matla a ho fetisetsoa ho betri e emeng e etsahala hang hang ha ho na tšitiso.
• Ho khaoha ha Alamo ea Mollo e hlokometsoeng (ho latching kapa ho se latching) 10K EOL resistor. E sebetsa ho trigger e tloahelehileng e bulehileng (NO) kapa ka tloaelo e koetsoeng (NC).
• AC e hloleha ho laola (ho theha mabitso a "C").
• Betri e hloleha le tlhokomelo ea boteng (foroha mabitso a "C").
• Ho tima matla a tlase. E koala li-terminals tsa DC haeba betri e le matlatage theoha ka tlase ho 71-73% bakeng sa li-unit tsa 12V le 70-75% bakeng sa li-unit tsa 24V (ho itšetlehile ka matla a matla). E thibela ho tsoa ha betri e tebileng.
• Bakeng sa litekanyetso tsa li-fuse sheba ho MaximalFDV Series Configuration Chart, pg. 3.
• Green AC Power LED e bonts'a 220VAC e teng.
• Lipontšo tsa LED tsa AC le tse hlahisoang ke DC.
• Tšireletso e khutšoanyane ea potoloho le tšireletso e feteletseng.
• Sebaka se ka har'a libethe tse fihlang ho tse 'ne (4) 12VDC/12AH.
  Litekanyo tse katiloeng (H x W x D): 26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm).

MaximalFDV Litaelo tsa ho Kenya:

Mekhoa ea lithapo e tla ba ho latela Khoutu ea Naha ea Motlakase/NFPA 70/ANSI, Khoutu ea Motlakase ea Canada, Karolo ea I, Karolo ea II le likhoutu tsohle tsa lehae le ba boholong ba nang le matla a ho laola. Sehlahisoa se reretsoe ho sebelisoa ka tlung feela.

Boto ea Phepelo ea Matla LED Diagnostics	(leq. 6)
Access Power Controller LED Diagnostics	(leq. 6)
Boitsebiso ba Boto ea Phepelo ea Matla	(leq. 6)
Fumana Boitsebiso ba Terminal Controller Power	(leq. 7)
Litlhaloso tsa Boto ea Phepelo ea Motlakase E eme ka Battery	(leq. 7)
Sephetho sa Boto ea Phepelo ea Matla Voltage Litlhophiso	(leq. 7)
Fihla Selaoli sa Matla Sets'oants'o se Tloaelehileng sa Kopo	(leq. 8)
FACP / Optional Power Supply Hook-up Diagrams	(leq. 11)

1. Beha yuniti sebakeng seo u se batlang. Tšoaea 'me u phunye masoba leboteng ho tsamaisana le likoti tse tharo tse ka holimo ka har'a sebaka se koalehileng. Kenya li-fasteners le li-screws tse tharo leboteng 'me lihlooho tsa screw li hlahelle. Beha masoba a ka holimo a kokelo holim'a likurufu tse tharo tse ka holimo, u be boemong 'me u sireletsehe. Tšoaea boemo ba likoti tse tharo tse tlase. Tlosa sebaka se kampetsoeng. Hlakola likoti tse ka tlase ebe u kenya li-fasteners tse tharo. Beha masoba a ka holimo a kokelo holim'a likurufu tse tharo tse ka holimo. Kenya li-screw tse tharo tse tlase 'me u tiise hore u tiisa li-screw tsohle (Enclosure Dimensions, pg. 12).
2. Hokela matla a AC a sa fetoheng (220VAC 50/60Hz) ho li-terminals tse tšoailoeng [L, N] (Setšoantšo sa 3, leqephe la 9). Se ke oa sebelisa theminale e tšoailoeng [G]. Sebelisa 14 AWG kapa e kholoanyane bakeng sa likhokahano tsohle tsa matla. Sireletsehile fatše terata etella lefatše fatše lug.
   Boloka lithapo tse lekanyelitsoeng matla li arohane le lithapo tse se nang matla.
   Bonyane sebaka sa sebaka sa 0.25" se tlameha ho fanoa.
   TLHOKOMELISO: U se ke ua tšoara likarolo tsa tšepe tse pepenene. Koala matla a potoloho ea lekala pele u kenya kapa u sebeletsa lisebelisoa. Ha ho na likarolo tse ka sebelisoang ke basebelisi ka hare. Fetisetsa ho kenya le ho fana ka litšebeletso ho basebeletsi ba nang le tsebo.
3. Khetha e lakatsehang DC output voltage ka ho beha SW1 sebakeng se loketseng ho matla a Maximal3FDV (setšoantšo sa 1a, pg. 7). Phepelo ea matla a Maximal5FDV ke feme e behiloeng ho 12VDC mme phepelo ea motlakase ea Maximal7FDV ke feme e behiloeng ho 24VDC.
4. Lekanya tlhahiso ea matlatage ea yuniti pele o hokela lisebelisoa life kapa life ho netefatsa ts'ebetso e nepahetseng. Phallo e sa lokang kapa e phahamengtage tla senya lisebelisoa tsena.
5. Likhetho tsa tlhahiso (setšoantšo sa 2, leqephe la 8):
   Yuniti e tla fana ka liphetho tsa motlakase tse fetotsoeng tse leshome le metso e tšeletseng (16), tse leshome le metso e ts'eletseng (16) tse ommeng tsa "C", kapa motsoako ofe kapa ofe oa matla a fetotsoeng le liphetho tsa "C".
   (a) Liphetho tsa Fail-Safe Switched Power:
   Bakeng sa ts'ebetso ea Fail-Safe, hokela kenyeletso e ntle (+) ea lisebelisoa tsa taolo ea phihlello ho theminale e tšoailoeng [NC]. Hokela molaetsa o fosahetseng (–) oa lisebelisoa tsa taolo ea phihlello ho terminal e tšoailoeng [COM].
   (b) Liphetho tsa Fail-Secure Switched Power:
   Bakeng sa ts'ebetso ea Fail-Sireletsehile, hokela tlhahiso e ntle (+) ea lisebelisoa tsa taolo ea phihlello ho terminal e tšoailoeng [NO]. Hokela molaetsa o fosahetseng (–) oa lisebelisoa tsa taolo ea phihlello ho terminal e tšoailoeng [COM].
6. Liphetho tsa Matla a ACM8CB (tse sa fetoheng):
   Hokela lisebelisoa tsa taolo ea phihlello tse hlokang matla a sa khaotseng ho litheminale tse tšoailoeng [C] positive (+) le [COM] negative (–). Lintho tse hlahisoang li ka sebelisoa ho fana ka matla bakeng sa babali ba likarete, li-keypad, joalo-joalo.
   Liphetho tsa eFlow (tse sa fetoloang):
   Bakeng sa khokahanyo ea lisebelisoa tse thusang tlhahiso ena e ke ke ea angoa ke Thibelo ea Matla a Tlase kapa Sehokelo sa Alarm ea Mollo. Hokela sesebelisoa ho li-terminals tse tšoailoeng [+ AUX -] (Setšoantšo sa 3, leqephe la 9).
7. Likhetho tsa ho kenya letsoho (setšoantšo sa 2, leqephe la 8):
   (a) Hangata Bula [NO] trigger ea ho kenya:
   Litlhahiso tsa 1-8 li kentsoe tšebetsong ka mokhoa o tloaelehileng oa ho kenya sekontiri se bulehileng kapa se bulehileng. Hokela liphetho tsa phanele ea phihlello, li-keypad, likonopo tse tobetsang, li-PIR tsa REX, joalo-joalo ho li-terminals tse tšoailoeng [IN] le [GND].
   (b) Open Collector Sink inputs:
   Hokela setsi sa taolo ea phihlello se bulehileng se bokellang se nepahetseng (+) ho li-terminals tse tšoailoeng [IN] le negative (–) ho litheminale tse tšoailoeng [GND].
8. ACM8CB Fire Alarm Interface khethang ho tsona (Setšoantšo sa 5-9, leqephe la 11):
   [NC] kapa ka tloaelo ho buloa [NO] ho kenya letsoho ho tsoa phanele ea taolo ea alamo ea mollo kapa keno e khutlisetsang polarity ho tsoa ho potoloho ea matšoao a FACP e tla ama liphetho tse khethiloeng.
   Ho nolofalletsa FACP Disconnect bakeng sa tlhahiso, tima switch(es) e tsamaellanang [SW1-SW8] TIMA botong e 'ngoe le e 'ngoe ea ACM8CB. Ho tima FACP hakoa bakeng sa tlhahiso, bulela switch(es) e tsamaellanang [SW1-SW8] ON botong ka 'ngoe ea ACM8CB.
   (a) Ka tloaelo Bula [NO] ho kenya:
   Bakeng sa ho se latching hook-up sheba Setšoantšo sa 6, leq. 11. Bakeng sa latching hook-up sheba Setšoantšo sa 7, leq. 11.
   (b) Hangata ho koetsoe [NC]:
   Bakeng sa ho se latching hook-up sheba Setšoantšo sa 8, leq. 11. Bakeng sa latching hook-up sheba Setšoantšo sa 9, leq. 11.
   (c) Sehlomathisi se kenyang Potoloho ea Letšoao la FACP:
   Hokela positive (+) le negative (–) ho tloha ho FACP signaling circuit output ho litheminale tse tšoailoeng [+ INP –]. Hokela FACP EOL ho li-terminals tse tšoailoeng [+ RET –] (polarity e hlalositsoe boemong ba alamo). Jumper e haufi le TRG LED e tlameha ho khaoloa (setšoantšo sa 5, leqephe la 11).
9. FACP Dry form "C" tlhahiso (setšoantšo sa 2b, leqephe la 8):
   Mabitso a mofuta oa "C" a FACP a ka sebelisoa ho qala lisebelisoa tsa ho tlaleha kapa ho fana ka matšoao.
   Li-contact tsena li sebelisa alamo ea mollo e kenyang liboto tsa ACM8CB.
10. Likhokahano tsa Battery tse Emeng (Setšoantšo sa 3, leqephe la 9):
    Bakeng sa lits'ebetso tsa Access Control, libeteri ke boikhethelo. Ha libetri li sa sebelisoe, tahlehelo ea AC e tla fella ka tahlehelo ea matla a tlhahisotage. Ha tšebeliso ea libeteri tse emeng li lakatseha, e tlameha ho ba acid ea lead kapa mofuta oa gel. Hokela betri ho li-terminals tse tšoailoeng [- BAT +] (Setšoantšo sa 3, leqephe la 9). Sebelisa libeteri tse peli (2) tsa 12VDC tse hokahaneng letotong bakeng sa ts'ebetso ea 24VDC (li-lead tsa betri li kenyelelitsoe). Sebelisa libeteri – Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) libeteri kapa libeteri tse amoheloang ke UL BAZR2 le BAZR8 tsa lintlha tse nepahetseng.
11. Liphetho tsa Battery le AC Supervision (Setšoantšo sa 3, leqephe la 9):
    Hoa hlokahala ho hokela lisebelisoa tsa tlaleho ea mathata a boetapele ho liphetho tse tšoailoeng [AC Fail, BAT Fail] tse tšoailoeng [NC, C, NO] ho lisebelisoa tse loketseng tsa tsebiso.
    Sebelisa 22 AWG ho isa ho 18 AWG bakeng sa tlaleho ea AC Fail & Low/No Bettery.
12. Ho liehisa tlaleho ea AC bakeng sa lihora tsa 2., Seta switjha ea DIP [AC Delay] ho ea ho OFF (setšoantšo sa 3, leqephe la 9).
    Ho liehisa tlaleho ea AC bakeng sa 1 min., Seta switjha ea DIP [AC Delay] ho boemo ba ON (setšoantšo sa 3, leqephe la 9).
13. Ho Khaola Alamo ea Mollo (Setšoantšo sa 3, leqephe la 9):
    Ho bulela Alamo ea Mollo Hakolla, seta switjha ea DIP [Shutdown] ho ea ho ON.
    Ho tima Alamo ea Mollo Hakolla seta switjha ea DIP [Shutdown] ho ea ho OFF.
14. Ho kenngoa ha tamper switch (Setšoantšo sa 3b, leqephe la 9):
    Thaba ea UL Listed tamper switjha (Altronix Model TS112 kapa e lekanang) ka holimo ho sebaka se kampetsoeng. Tsamaisa tamper switjha bracket moeling oa sebaka se koaletsoeng hoo e ka bang 2 "ho tloha ka lehlakoreng le letona (setšoantšo sa 3b, leqephe la 9).
    Kopanya tamper switch wiring ho ea ho Access Control Panel kapa sesebelisoa se nepahetseng sa tlaleho se Lethathameng la UL. Ho kenya letshwao la alamo tshebetsong, bula lemati la sebaka se kampeleng.
15. Lisebelisoa tse ngata tsa motlakase (setšoantšo sa 2, leqephe la 8):
    Ha u sebelisa matla a eketsehileng a ka ntle, li-jumpers J1 le J2 tse teng holim'a boto ea ACM8 e lumellanang e tlameha ho khaoloa (setšoantšo sa 2c, 2d, pg. 8). Hokela phepelo ea motlakase ea taolo ea phihlello ea kantle ho litheminale tse tšoailoeng [- Control +] (Litheminale tsena li bapetsoe le litheminale tsa [- Power +]). Ha u sebelisa lisebelisoa tsa motlakase tsa DC, polarity e tlameha ho hlokomeloa. Ha o sebelisa lisebelisoa tsa motlakase tsa AC, polarity ha ea lokela ho bonoa.
    (Setšoantšo sa 2d, leqephe la 8) Likhokahanyo tsohle tsa marang-rang li tlameha ho etsoa ho sebelisa gauge e loketseng ea CM kapa FPL jacketed terata kapa sebaka se lekanang le sona (setšoantšo sa 4a, leqephe la 10).

Tlhokomelo:

Tlhokomelo: Yuniti e lokela ho lekoa bonyane hang ka selemo bakeng sa ts'ebetso e nepahetseng ka tsela e latelang:
Tlhokomelo ea FACP: Ho etsa bonnete ba hore ho na le khokahanyo e nepahetseng le ts'ebetso ea khokahanyo ea ho hakolla Alarm ea Mollo, ka kopo latela mokhoa o nepahetseng o ka tlase: Ka tloaelo Puo e Bulehileng: Ho beha sebaka se khuts'oane lipakeng tsa litheminale tse tšoailoeng [T] le [+ INP] ho tla etsa hore ho hakoe Alarm ea Mollo. Tlosa e khutšoanyane ho tsosolosa.
Kenyelletso e Tlwaelehileng ka Tlwaeleho: Ho tlosa terata ho theminale e ngotsweng [INP –] ho tla etsa hore ho Kgaolwe Alamo ya Mollo. Fetolela terata ho theminale e tšoailoeng [INP –] ho seta botjha.
Kenyelletso ea Potoloho ea Letšoao la FACP: Hoa hlokahala ho qala Sesebelisoa sa Alarm ea Mollo. Liketsahalong tsohle tse ka holimo TRG LED e tala ea ACM8s e tla khantša. Liphetho tsohle tse khethiloeng bakeng sa Fire Alarm Disconnect li tla kenya tšebetsong lisebelisoa tse notlelang.
Ela hloko: Liphetho tsohle [OUT 1 – OUT 8] li tlameha ho ba boemong bo tloaelehileng (ho felloa ke matla) pele ho tlhahlobo. Ha yuniti e lokiselitsoe ka tloaelo Open (setšoantšo sa 7, leqephe la 11) kapa se Koetsoe ka tloaelo (setšoantšo sa 9, leqepheng la 11) ho hlokahala hore u sete botjha ho Khaola Alarm ea Mollo ka ho kenya switjha e tloaelehileng e koetsoeng.
Khumo Voltage Teko: Tlas'a maemo a tloaelehileng a mojaro, molumo oa DC oa voltage lokela ho hlahlojwa bakeng sa vol e nepahetsengtage level (sheba MaximalFDV series Configuration Chart, pg. 3).
Teko ea Battery: Tlas'a maemo a tloaelehileng a mojaro, hlahloba hore na betri e tjhajiloe ka botlalo, hlahloba molumo o boletsoengtage liteisheneng tsa betri le liteisheneng tsa boto tse tšoailoeng [+ BAT –] ho netefatsa hore ha ho na ho khaoha lithapong tsa ho hokela betri.
Hlokomela: Boholo ba tefiso ea hajoale ke 1.54A. Bophelo ba betri bo lebelletsoeng ke lilemo tse 5; leha ho le joalo, ho kgothaletswa ho fetola dibetri nakong ya dilemo tse 4 kapa ka tlase ha ho hlokahala.

Tlhahlobo ea LED ea Boto ea Phepelo ea Matla:

Khubelu (DC)	Botala (AC/AC1)	Boemo ba Phepelo ea Matla
ON	ON	Boemo bo tloaelehileng ba ts'ebetso.
ON	TLOA	Tahlehelo ea AC. Matla a ho fana ka betri e emeng.
TLOA	ON	Ha ho tlhahiso ea DC.
TLOA	TLOA	Tahlehelo ea AC. Betri e emeng kapa e sa sebetseng. Ha ho tlhahiso ea DC.

Khubelu (Bat)	Boemo ba Battery
ON	Boemo bo tloaelehileng ba ts'ebetso.
TLOA	Betri e hlolehile/betri e tlase.

Fumana Tlhahlobo ea LED ea Taolo ea Matla:

LED	ON	TLOA
LED 1- LED 8 (Khubelu)	Li-relay tse hlahisoang li matlafalitsoe.	Li-relay li feletsoe ke matla.
Trg (Tala)	Ho kenya FACP (boemo ba alamo).	FACP e tloaelehileng (boemo boo e seng alamo).

Boitsebiso ba Boto ea Phepelo ea Matla:

Terminal Taba	Mosebetsi/Tlhaloso
L, N	Hokela 220VAC 50/60Hz ho li-terminals tsena: L ho ea ho chesa, N ho se nke lehlakore. Se ke oa sebelisa theminale e tšoailoeng [G]
+ DC -	Feme e hokahaneng le boto ea ACM8.
Hlahisa EOL Tlhokomelo	Sebopeho sa Alarm ea Mollo se kenya letsoho ho tsoa ho nako e khuts'oane kapa FACP. Litlhahiso tse kenang li ka ba tse tloaelehileng bula, hangata e koetsoe ho tloha ho FACP output circuit (Fig. 3, pg. 9).
CHE, GND RESET	FACP segokanyimmediamentsi sa sebolokigolo latching kapa bao e seng latching (sa feiga. 3, leqepheng la 9).
+ AUX -	Tlhahiso e thusang e lekantsoe 0 1A (e sa fetoheng) (setšoantšo sa 3, leqephe la 9).
AC HLOLA NC, C, Che	E bontsha tahlehelo ya matla a AC, mohlala, hokela sesebedisweng se utlwahalang kapa phanele ya alamo. Relay hangata e matlafatsoa ha matla a AC a le teng. Tlhaloso ea ho kopana 1A 0 30VDC (setšoantšo sa 3, leqephe la 9).
HLOKOMELA KHABANE NC, C, Che	E supa boemo ba betri e tlase, mohlala, hokela ho phanele ea alamo. Relay hangata e matlafatsoa ha motlakase oa DC o le teng. Tlhaloso ea ho ikopanya 1A 0 30VDC. Betri e tlositsoeng e tlalehoa nakong ea metsotso e 5. Khokahano ea betri e tlalehoa nakong ea motsotso oa 1 (setšoantšo sa 3, leqephe la 9).
+ BAT -	Lihokelo tsa betri tse emeng. Boholo ba tefiso ea hona joale 1.54A (setšoantšo sa 3, leqephe la 9).

Fumana Boitsebiso ba Terminal Controller Power:

Terminal Taba	Mosebetsi/Tlhaloso
- Matla +	12VDC kapa 24VDC ho tloha phepelong ea motlakase / tjhaja (fektheri e hokahaneng). Li-terminals tsena li bapisoa le li-terminals tsa [— Control +].
- Taolo +	Litheminale tsena li bapisoa le li-terminals tsa [- Power +]. Li-terminals tsena li ka hokeloa phepelong ea motlakase ea taolo ea phihlello ea kantle ho fana ka matla a ho sebetsa a ikhethileng bakeng sa lisebelisoa. Li-Jumpers J1 le J2 li tlameha ho tlosoa.
TRIGGER INPUT1 - SE KENYA 8 HO, GND	Ho tsoa ho tse tloaelehileng tse bulehileng le/kapa tse bulehileng tsa pokello ea sink trigger (kopo ea ho tsoa likonopo, ho tsoa li-PIR, joalo-joalo)
TLHALOSO 1- PHELETSO 8 NC, C, NO, COM	Liphetho tse laoloang ke 12VDC ho isa ho 24VDC li lekantsoe ho 2.5A. Maximal3FDV - 10.0-13.2VDC 0 4.6A kapa 20.19-26.4VDC 0 5.2A. Maximal5FDV - 10.03-13.2VDC 0 8.6A. Maximal7FDV - 20.17-26.4VDC 0 9.2A. Fail-Safe [NC positive (+) & COM Negative (—)], Fail-Sireletsehile [HA HO positi (+) & COM Negative (—)], tlhahiso e thusang [C positive (+) & COM Negative (—)]. Ha o sebelisa lisebelisoa tsa motlakase tsa AC polarity ha ea lokela ho bonoa. Mabitso a bonts'itsoeng a sa qalelle.
FACP SEBAKA T, + INPUT -	Sehokelo sa Alarm ea Mollo se kenya letsoho ho tsoa ho FACP. Lisebelisoa tsa ho kenya li ka buloa hangata, hangata e koetsoe ho tsoa ho phallo ea potoloho ea pontšo ea FACP (Figs. 5-9, pg. 11).
FACP SEBAKA NC, C, Che	Foromo "C" relay contact rated @ 1A 28VDC bakeng sa tlaleho ea alamo.

Litlhaloso tsa Battery tsa Boto ea Phepelo ea Matla:

Betri	Boholo ba 3FDV	Boholo ba 5FDV	Boholo ba 7FDV
7AH	10 mets./6A	5 mets./10A	5 mets./10A
12AH	30 mets./6A	30 mets./10A	30 mets./10A
40AH	Ho feta lihora tse 4/6A	Ho feta lihora tse 2/10A	Ho feta lihora tse 2/10A
65AH	Ho feta lihora tse 4/6A	Ho feta lihora tse 4/10A	Ho feta lihora tse 4/10A

Sephetho sa Boto ea Phepelo ea Matla Voltage Litlhophiso:

Setšoantšo se Tloaelehileng sa Selaoli sa Motlakase (bakeng sa ACM8CB ka 'ngoe):

Setšoantšo sa 3 - Maximal3FDV, Maximal5FDV, le Maximal7FDV

TLHOKOMELISO: Ha boto ea phepelo ea motlakase e setetsoe 12VDC sebelisa betri e le 'ngoe feela (1) 12VDC e emeng.
Boloka lithapo tse lekanyelitsoeng matla li arohane le tse se nang matla.
Sebelisa sebaka sa bonyane 0.25 ″.
12AH Libetri tse ka chachang hape ke libeteri tse kholo ka ho fetisisa tse ka kenang ka har'a sebaka sena se kampetsoeng. Sebaka se ka ntle sa betri se tlameha ho sebelisoa ha u sebelisa libeteri tsa 40AH kapa 65AH.

Litlhokahalo tsa Wiring tse lekantsoeng ke NEC:

Lithapo tsa motlakase tse se nang matla le tse se nang matla li tlameha ho lula li arohane ka khabinete. Lithapo tsohle tsa potoloho tse nang le matla a fokolang li tlameha ho lula bonyane 0.25 ″ hole le lithapo life kapa life tsa potoloho tse se nang matla. Ho feta moo, lithapo tsohle tse nang le matla a fokolang a matla le lithapo tse se nang matla a motlakase li tlameha ho kena le ho tsoa ka har'a khabinete ka likotopo tse fapaneng.
E 'ngoe ea mohlala o joaloampsena se bontšoa ka tlase. Sesebelisoa sa hau se ikhethileng se ka hloka hore ho sebelisoe li-conduit knockouts tse fapaneng. Ho ka sebelisoa likotopo life kapa life tsa conduit. Bakeng sa lits'ebetso tse lekanyelitsoeng ho sebelisa motlakase ke boikhethelo. Likhokelo tsohle tsa methapo li tlameha ho etsoa ho sebelisa gauge e loketseng ea CM kapa FPL jacket terata (kapa e tšoanang le sebaka sa eona).
Sebaka sa boikhethelo sa UL se ka har'a betri se tlameha ho kenngoa haufi le phepelo ea motlakase ka mekhoa ea mehala ea Sehlopha sa 1.
Bakeng sa lisebelisoa tsa Canada sebelisa wiring e sirelelitsoeng bakeng sa likhokahano tsohle.
Hlokomela: Sheba setšoantšo sa ho tšoara mohala ka tlase bakeng sa mokhoa o nepahetseng oa ho kenya terata e koetsoeng ea CM kapa FPL (Setšoantšo sa 4a).

FACP Hook-Up Diagrams:

Setšoantšo sa 5 Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo):	Setšoantšo sa 6 Ka tloaelo Bulehile: Non-Latching FACP kenya letsoho:
Setšoantšo sa 7 Ka tloaelo Open FACP Latching trigger input with reset (Sephetho sena ha se so hlahlojoe ke UL):	Setšoantšo sa 8 se Koalehile ka tloaelo: Ho kenya FACP e sa Lateng:
Setšoantšo sa 9 Hangata se Koetsoe: Latching FACP trigger input with reset (Sephetho sena ha se so hlahlojoe ke UL):

Mekhahlelo ea Kakaretso (H x W x D e batla e lekanyelitsoe):
26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm)

Altronix ha e ikarabelle bakeng sa liphoso leha e le life tsa typographical.
140 58th Street, Brooklyn, New York 11220 USA | mohala: 718-567-8181 | fax: 718-567-9056
websebaka: www.altelengx.com | lengolo-tsoibila: info@altronix.com | Warranty ea bophelo bohle
IIMaximal3FDV/5FDV/7FDV Series
H13U
Maximal3FDV/5FDV/7FDV Series (PTC) Tataiso ea ho Kena

Litokomane / Lisebelisoa

Altronix Maximal7FDV Access Power Controllers [pdf] Buka ea Taelo Maximal7FDV Access Power Controllers, Maximal7FDV, Access Power Controllers, Power Controllers, Controllers

Litšupiso

• Bukana ea Mosebelisi