Mafi girman jerin FDV
Powerarfin Wuta Singleaya
Masu Gudanar da Wutar Lantarki (PTC)
Jagoran Shigarwa

Maximal7FDV Masu Kula da Wutar Lantarki

Model sun hada da:
Saukewa: FDV3
- 12VDC @ 4.6A ko 24VDC @ 5.2A.
– Goma sha shida (16) PTC abubuwan kariya.
Saukewa: FDV5
- 12VDC @ 8.6A.
– Goma sha shida (16) PTC abubuwan kariya.
Saukewa: FDV7
- 24VDC @ 9.2A.
– Goma sha shida (16) PTC abubuwan kariya.

Saukewa: SFDV031115
Kamfanin Shiga: _________________
Sunan Wakilin Sabis: ________________
Adireshi: ________________________
Waya #: ________________________________

MaximalFDV Series Overview:

Altronix MaximalFDV Samun Wuta/Masu sarrafawa suna rarrabawa da canza wuta don samun damar tsarin sarrafawa da na'urorin haɗi. Suna canza 220VAC (kewayon aiki 198VAC – 256VAC), shigarwar 50/60Hz zuwa goma sha shida (16) mai sarrafa 12VDC ko 24VDC PTC da aka karewa. Ana kunna abubuwan da aka fitar ta hanyar buɗaɗɗen ruwa mai tattarawa ko kuma buɗe (NO) busassun shigar da busassun shigarwa daga Tsarin Kulawa, Maɓalli, Maɓallin turawa, REX PIR, da sauransu. Raka'a za su tura wuta zuwa na'urori masu sarrafa dama iri-iri ciki har da: Mag Locks , Yajin Wutar Lantarki, Masu riƙe Ƙofa na Magnetic, da sauransu. Fannin FACP yana ba da damar gaggawar gaggawa, Kula da ƙararrawa, ko ana iya amfani da su don kunna wasu na'urori masu taimako. Siffar cire haɗin ƙararrawar wuta ana iya zaɓa ɗaya ɗaya don kowane ko duka na sha shida (16).

Jadawalin Kanfigareshan MaximalFDV:

Waɗannan raka'a sun dace da iko: na'urori masu auna firikwensin, na'urorin injin lantarki (misali bugun kofa na lantarki).

Siffofin MaximalFDV:

Modules Masu Kula da Wutar Lantarki ACM8CB:

• Goma sha shida (16) suna jawo abubuwan sarrafawa da kansu. Zaɓuɓɓukan fitarwa:
  a) Goma sha shida (16) Fail-Safe tace wutar lantarki.
  b) Goma sha shida (16) Rashin tsaro tace abubuwan wuta.
  c) Duk wani hade na sama.
• Goma sha shida (16) Shigar da tsarin sarrafawa yana jawo abubuwan shiga. Zaɓuɓɓukan shigar da kunnawa:
  a) Goma sha shida (16) buɗaɗɗen abubuwan shigar da busassun abubuwa (NO).
  b) Goma sha shida (16) abubuwan shigar masu tarawa.
  c) Duk wani hade na sama.
• Goma sha shida (16) tace aux. abubuwan wuta (ana kimanta abubuwan da aka fitar @ 2.5A).
• Jajayen LED a kan allon ACM8CB suna nuna abubuwan da aka kunna kai tsaye (masu kuzari).
• Cire haɗin ƙararrawa na Wuta (latching ko rashin latching) ana iya zaɓin ɗaiɗaiku don kowane ko duka na sha shida (16).
  Zaɓuɓɓukan shigar da ƙararrawa na Wuta:
  a) Buɗewa ta al'ada (NO) ko kuma rufe (NC) busasshen shigar da faɗakarwa.
  b) shigarwar juyar da polarity daga da'irar siginar FACP.
• Green LED akan allon ACM8CB yana nuna cire haɗin FACP.
• Fassarar fitarwa ta FACP yana nuna cewa an kunna shigar da FACP (nau'in lamba "C" mai ƙima @ 1A/28VDC).
• eFlow Power Supply/Caja allo yana ba da iko gama gari don allunan Kula da Wutar Lantarki na ACM8CB (wayoyin masana'antu) da duk na'urorin sarrafa damar shiga (filin wayoyi).
• ACM8CB babban fuses an ƙididdige su @ 10A. Ana ƙididdige fitar da PTCs @ 2.5A.

Samar da Wutar Wuta/Caji:

• Shigarwa: 220VAC (Kewayon aiki 198VAC - 256VAC), 50/60Hz.
• Don fitarwa voltage da samar da halin yanzu koma zuwa MaximalFDV jerin Kanfigareshan Chart, shafi. 3.
• Mahimmin fitarwa na taimako @ 1A (ba a canza ba).
• Ƙarfafawatage Kariya.
• Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura na gel.
• Matsakaicin caji na yanzu 1.54A.
• Canja atomatik zuwa baturin jiran aiki lokacin da AC ta gaza.
  Canja wurin zuwa ƙarfin baturi yana nan take ba tare da katsewa ba.
• Cire haɗin Ƙararrawar Wuta da ake kulawa (latching ko mara latching) 10K EOL resistor. Yana aiki akan fararwa na yau da kullun (NO) ko rufaffiyar (NC).
• AC gaza kulawa (form "C" lambobin sadarwa).
• Rashin batir da kulawar kasancewar (form "C" lambobin sadarwa).
• Ƙarfin wutar lantarki. Yana rufe tashoshin fitarwa na DC idan baturi voltage ya faɗi ƙasa 71-73% don raka'a 12V da 70-75% don raka'a 24V (dangane da wutar lantarki). Yana hana zurfafa fitar da baturi.
• Don ƙimar fis koma zuwa MaximalFDV Series Kanfigareshan Chart, shafi. 3.
• Green AC Power LED yana nuna 220VAC yanzu.
• Shigar da AC da alamun fitarwa na LED.
• Gajeren kewayawa da kariyar wuce gona da iri.
• Yakin yana ɗaukar batura har zuwa huɗu (4) 12VDC/12AH.
  Girman yadi (H x W x D): 26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm).

Umarnin Shigarwa MaximalFDV:

Hanyoyin wayoyi za su kasance daidai da Lambar Lantarki ta Ƙasa/NFPA 70/ANSI, Lambar Lantarki ta Kanada, Sashe na I, Sashe na II kuma tare da duk lambobin gida da hukumomi masu iko. An yi nufin samfurin don amfanin cikin gida kawai.

Kayan Wutar Lantarki LED Diagnostics	(shafi na 6)
Samun damar Mai Kula da Wutar Lantarki LED Diagnostics	(shafi na 6)
Ƙirar Tasha Tashar Tashar Wuta	(shafi na 6)
Samun Gano Tasha Mai Kula da Wuta	(shafi na 7)
Ƙimar Samar da Wutar Lantarki Takaddun Bayanan Baturi	(shafi na 7)
Fitar da Wutar Lantarki Voltage Saituna	(shafi na 7)
Hannun Hannun Aikace-aikacen Mai Gudanar da Wuta	(shafi na 8)
Zane-zane na Ƙirar Ƙimar Ƙarfafawa na FACP/Zaɓi	(shafi na 11)

1. Dutsen naúrar a wurin da ake so. Yi alama da ramuka a bango don yin layi tare da manyan rijiyoyin maɓalli uku a cikin shingen. Shigar da manyan haɗe-haɗe guda uku da sukurori a bango tare da ɗumbin kawunan suna fitowa. Sanya manyan rijiyoyin maɓalli na sama sama da sukurori uku na sama, matakin kuma amintattu. Alama matsayi na ƙananan ramuka uku. Cire shingen. Hana ƙananan ramuka kuma shigar da masu ɗaure uku. Sanya ramukan maɓalli na sama sama da sukurori uku na sama. Shigar da ƙananan sukurori guda uku kuma tabbatar da ƙarfafa duk screws (Ƙaƙƙarfan Ƙirar, shafi 12).
2. Haɗa ƙarfin AC da ba a kunna ba (220VAC 50/60Hz) zuwa tashoshi masu alama [L, N] (Hoto 3, shafi 9). Kada a yi amfani da tasha mai alamar [G]. Yi amfani da 14 AWG ko mafi girma don duk haɗin wutar lantarki. Amintaccen waya ta ƙasa tana kaiwa zuwa ƙasa lug.
   Kiyaye iyakataccen wayoyi daban da wayoyi marasa iyaka.
   Dole ne a samar da tazara mafi ƙarancin 0.25.
   HANKALI: Kar a taɓa sassan ƙarfe da aka fallasa. Kashe wutar da'irar reshe kafin shigarwa ko kayan aiki. Babu sassa masu amfani a ciki. Koma shigarwa da sabis zuwa ƙwararrun ma'aikatan sabis.
3. Zaɓi fitarwa DC da ake so voltage ta hanyar saita SW1 zuwa matsayi mai dacewa akan wutar lantarki Maximal3FDV (Fig. 1a, shafi 7). Maximal5FDV samar da wutar lantarki an saita masana'anta a 12VDC kuma Maximal7FDV samar da wutar lantarki an saita masana'anta a 24VDC.
4. Auna fitarwa voltage na naúrar kafin haɗa kowane na'ura don tabbatar da aiki mai kyau. Ba daidai ba ko high voltage zai lalata waɗannan na'urori.
5. Zaɓuɓɓukan fitarwa (Hoto 2, shafi 8):
   Naúrar za ta samar da ko dai guda goma sha shida (16) da aka canza wutar lantarki, sha shida (16) busasshen nau'in "C", ko duk wani haɗin da aka canza da kuma samar da fitowar "C".
   (a) Fail-Safe Canja Wutar Wuta:
   Don Fail-Safe aiki haɗa ingantaccen shigarwar (+) na na'urorin sarrafa damar shiga zuwa tasha mai alama [NC]. Haɗa shigarwar mara kyau (-) na na'urorin sarrafa damar shiga zuwa tasha mai alama [COM].
   (b) Fail-Secure Canja Wutar Wuta:
   Don Aiwatar da Amintaccen aiki haɗa ingantaccen shigarwar (+) na na'urorin sarrafa shiga zuwa tasha mai alama [NO]. Haɗa shigarwar mara kyau (-) na na'urorin sarrafa damar shiga zuwa tasha mai alama [COM].
6. ACM8CB Abubuwan Wutar Taimako (ba a kunna ba):
   Haɗa na'urorin sarrafa damar shiga waɗanda ke buƙatar iko akai-akai zuwa tashoshi masu alama [C] tabbatacce (+) da [COM] korau (-). Ana iya amfani da abubuwan da aka fitar don samar da wuta ga masu karanta katin, maɓalli, da sauransu.
   Abubuwan Taimako na eFlow (ba a kunna ba):
   Don haɗin na'ura mai taimako wannan fitarwa ba zai shafe shi ta Ƙarƙashin Haɗin Wutar Wuta ko Interface Ƙararrawa ta Wuta. Haɗa na'urar zuwa tashoshi masu alamar [+ AUX -] (Hoto 3, shafi 9).
7. Zaɓuɓɓukan shigar da ƙara (Hoto 2, shafi 8):
   (a) Kullum Buɗe [NO] shigar da fararwa:
   Ana kunna abubuwan shigarwa 1-8 ta hanyar buɗewa ko buɗe abubuwan shigar da ruwa mai tarawa. Haɗa abubuwan sarrafa ikon samun dama, faifan maɓalli, maɓallan turawa, REX PIRs, da sauransu zuwa tashoshi masu alama [IN] da [GND].
   (b) Buɗe abubuwan shigar da Mai Tari:
   Haɗa kwamitin kula da hanyar shiga buɗaɗɗen mai tarawa tabbatacce (+) zuwa tashoshi masu alama [IN] da korau (-) zuwa tashoshi masu alama [GND].
8. ACM8CB Zaɓuɓɓukan Interface Ƙararrawar Wuta (Figs. 5-9, shafi 11):
   Rufewar [NC] ko buɗe [NO] da aka saba buɗewa daga rukunin kula da ƙararrawa na wuta ko shigarwar juyar da polarity daga da'irar siginar FACP zai shafi abubuwan da aka zaɓa.
   Don ba da damar Cire haɗin FACP don fitarwa, kunna madaidaicin (s) [SW1-SW8] KASHE akan kowane allon ACM8CB. Don musaki cire haɗin FACP don fitarwa, kunna madaidaicin (s) [SW1-SW8] ON akan kowane allon ACM8CB.
   (a) Buɗe [NO] yawanci:
   Don ƙugiya mara latching koma zuwa Hoto 6, shafi. 11. Domin latching ƙugiya-up koma zuwa siffa 7, shafi. 11.
   (b) Akan rufe [NC] shigarwa:
   Don ƙugiya mara latching koma zuwa Hoto 8, shafi. 11. Domin latching ƙugiya-up koma zuwa siffa 9, shafi. 11.
   (c) FACP Siginar shigar da madauri mai faɗakarwa:
   Haɗa tabbataccen (+) da korau (-) daga fitowar sigina na FACP zuwa tashoshi masu alama [+ INP -]. Haɗa FACP EOL zuwa tashoshi masu alamar [+ RET -] (an yi la'akari da polarity a cikin yanayin ƙararrawa). Jumper dake kusa da TRG LED dole ne a yanke (Fig. 5, shafi 11).
9. FACP Dry form “C” fitarwa (Hoto 2b, shafi 8):
   FACP form “C” lambobin sadarwa za a iya amfani da su jawo rahoto ko sigina na'urorin.
   Waɗannan lambobin sadarwa suna canzawa akan shigar da ƙararrawar wuta zuwa allon ACM8CB.
10. Haɗin Batir na tsaye (Hoto 3, shafi 9):
    Don aikace-aikacen Ikon Samun batir batir na zaɓi ne. Lokacin da ba a yi amfani da batura ba, asarar AC zai haifar da asarar juzu'in fitarwatage. Lokacin da ake son amfani da batura masu aiki, dole ne su zama nau'in gubar acid ko gel. Haɗa baturi zuwa tashoshi masu alama [- BAT +] (Hoto 3, shafi 9). Yi amfani da batura guda biyu (2) 12VDC da aka haɗa a jeri don aikin 24VDC (an haɗa da jagororin baturi). Yi amfani da batura - Casil CL1270 (12V / 7AH), CL12120 (12V / 12AH), CL12400 (12V / 40AH), CL12650 (12V / 65AH) batura ko UL gane batir BAZR2 da BAZR8 na ƙimar da ta dace.
11. Abubuwan Baturi da Kulawar AC (Hoto 3, shafi 9):
    Ana buƙatar haɗa na'urori masu ba da rahoton matsala masu kulawa zuwa abubuwan da aka yiwa alama [AC Fail, BAT Fail] na'urorin sa ido masu alama [NC, C, NO] zuwa na'urorin sanarwar gani da suka dace.
    Yi amfani da 22 AWG zuwa 18 AWG don gazawar AC & Ƙananan / Babu rahoton baturi.
12. Don jinkirta rahoton AC na sa'o'i 2., saita sauya DIP [AC Jinkiri] zuwa matsayin KASHE (Fig. 3, shafi 9).
    Don jinkirta rahoton AC na 1 min., saita sauya DIP [AC Jinkiri] zuwa ON matsayi (Fig. 3, shafi 9).
13. Cire Haɗin Ƙararrawar Wuta (Hoto 3, shafi 9):
    Don kunna Cire Haɗin Ƙararrawar Wuta saita sauya DIP [Rufewa] zuwa Matsayin ON.
    Don kashe Ƙararrawar Wuta Cire haɗin yanar gizo saita sauya DIP [Rufewa] zuwa KASHE matsayi.
14. Shigar da tampcanza (Hoto 3b, shafi 9):
    Dutsen UL Jerin tamper canza (Altronix Model TS112 ko makamancinsa) a saman shingen. Zamar da tampmadaidaicin madaidaicin maɓalli a gefen shingen kusan 2” daga gefen dama (Fig. 3b, shafi 9).
    Haɗa tampcanza wayoyi zuwa shigar da Panel Control Panel ko na'urar da aka jera UL mai dacewa. Don kunna siginar ƙararrawa, buɗe ƙofar shingen.
15. Abubuwan shigar da wutar lantarki da yawa (Hoto 2, shafi 8):
    Lokacin amfani da ƙarin wutar lantarki na waje, masu tsalle J1 da J2 da ke kan allon ACM8 daidai dole ne a yanke (Fig. 2c, 2d, shafi 8). Haɗa samar da wutar lantarki ta hanyar samun damar waje zuwa tashoshi masu alamar [- Control +] (Wadannan tashoshi suna daidaita da tashoshi na [- Power +]). Lokacin amfani da kayan wuta na DC, dole ne a lura da polarity. Lokacin amfani da kayan wuta na AC, bai kamata a lura da polarity ba.
    (Siffa 2d, shafi 8) Duk hanyoyin haɗin yanar gizo dole ne a yi amfani da ma'auni mai dacewa CM ko FPL waya mai jaket ko makamancinsa (Hoto 4a, shafi 10).

Kulawa:

Kulawa: Ya kamata a gwada naúrar aƙalla sau ɗaya a shekara don aikin da ya dace kamar haka:
Kulawa na FACP: Don tabbatar da haɗin kai mai kyau da aiki na cire haɗin haɗin ƙararrawar wuta, da fatan za a bi hanyar da ta dace a ƙasa: Buɗe Shigarwa ta al'ada: Sanya gajere tsakanin tashoshi masu alamar [T] da [+ INP] zai haifar da Cire Haɗin Ƙararrawar Wuta. Cire gajeriyar don sake saitawa.
Shigar da Ake Rufe: Cire waya daga tasha mai alama [INP -] zai haifar da Cire Haɗin Ƙararrawar Wuta. Sauya waya zuwa tasha mai alama [INP -] don sake saitawa.
Shigar da siginar siginar FACP: Wajibi ne don kunna Tsarin ƙararrawa na Wuta. A cikin duk yanayin da ke sama koren TRG LED na ACM8s zai haskaka. Duk abubuwan da aka zaɓa don Cire Haɗin Ƙararrawar Wuta za su kunna na'urorin kullewa.
Lura: Duk abubuwan da aka fitar [OUT 1 - OUT 8] dole ne su kasance cikin yanayin al'ada (wanda ba shi da kuzari) kafin gwaji. Lokacin da aka saita naúrar don Buɗe Al'ada (Hoto 7, shafi 11) ko Kullum Rufewa (Fig. 9, shafi 11) aiki latching dole ne a sake saita Alamar Ƙararrawar Wuta ta kunna maɓallin sake saiti na Kullum Rufe.
Fitarwa Voltage Gwaji: A ƙarƙashin yanayin kaya na yau da kullun, fitowar DC voltage ya kamata a duba don daidai voltage matakin (koma zuwa MaximalFDV jerin Kanfigareshan Chart, shafi 3).
Gwajin baturi: A ƙarƙashin yanayin kaya na al'ada duba cewa an cika cajin baturin, duba ƙayyadaddun voltage a tashoshin baturi da kuma tashoshin allon allo masu alamar [+ BAT -] don tabbatar da cewa babu karya a cikin wayoyi masu haɗin baturi.
Lura: Matsakaicin cajin halin yanzu shine 1.54A. Rayuwar baturi da ake tsammani shine shekaru 5; duk da haka, ana bada shawarar canza batura a cikin shekaru 4 ko ƙasa da haka idan ya cancanta.

Bayanan Wutar Lantarki LED Diagnostics:

Ja (DC)	Green (AC/AC1)	Matsayin Samar da Wuta
ON	ON	Yanayin aiki na al'ada.
ON	KASHE	Asarar AC. Batir yana ba da ƙarfi ta tsaye.
KASHE	ON	Babu fitarwa na DC.
KASHE	KASHE	Asarar AC. An cire ko babu baturi mai jiran aiki. Babu fitarwa na DC.

Ja (Jemage)	Matsayin baturi
ON	Yanayin aiki na al'ada.
KASHE	Baturi gazawa/ƙarancin baturi.

Samun damar Mai Kula da Wutar Lantarki LED Diagnostics:

LED	ON	KASHE
LED 1-LED 8 (ja)	Relay(s) na fitar da kuzari.	Relay(s) na fitar da kuzari.
Trg (Green)	An kunna shigar da FACP (yanayin ƙararrawa).	FACP na al'ada (yanayin rashin ƙararrawa).

Ƙirar Tasha Tashar Tashar Wuta:

Labarin Ƙarshe	Aiki/Bayyana
L, N	Haɗa 220VAC 50/60Hz zuwa waɗannan tashoshi: L zuwa zafi, N zuwa tsaka tsaki. Kar a yi amfani da tasha mai alamar [G]
+ DC —	Factory da aka haɗa zuwa allon ACM8.
Farashin EOL Ana kulawa	Wuta Ƙararrawa Interface yana jawo shigarwar shigarwa daga gajere ko FACP. Abubuwan shigarwa na iya zama al'ada budewa, yawanci rufewa daga da'irar fitarwa ta FACP (Hoto 3, shafi 9).
A'a, Sake saitin GND	FACP interface latching ko rashin latching (Fig. 3, shafi. 9).
+ AUX -	Fitowar taimako mai ƙima 0 1A (ba a kunna ba) (Fig. 3, shafi 9).
AC GASKIYA NC, C, BA	Yana nuna asarar wutar AC, misali haɗi zuwa na'ura mai ji ko ƙararrawa. Relay yawanci ana samun kuzari lokacin da wutar AC ta kasance. Ƙimar lamba 1A 0 30VDC (Hoto 3, shafi 9).
GASKIYA BAT NC, C, BA	Yana nuna ƙarancin yanayin baturi, misali haɗa zuwa panel ƙararrawa. Relay yawanci ana samun kuzari lokacin da ikon DC ya kasance. Ƙimar lamba 1A 0 30VDC. Ana ba da rahoton cire baturi a cikin mintuna 5. An ba da rahoton sake haɗa baturi a cikin minti 1 (Fig. 3, shafi 9).
+ BAT -	Haɗin baturi na tsaye. Matsakaicin caji na yanzu 1.54A (Fig. 3, shafi 9).

Samun Gano Tasha Mai Kula da Wuta:

Labarin Ƙarshe	Aiki/Bayyana
- Power +	12VDC ko 24VDC daga wutar lantarki / caja (ma'aikata da aka haɗa). Waɗannan tashoshi suna daidaitawa da tashoshi na [- Control +].
- Sarrafa +	Waɗannan tashoshi suna daidaitawa da tashoshi na [- Power +]. Ana iya haɗa waɗannan tashoshi zuwa wutar lantarki mai sarrafa damar shiga waje don samarwa keɓe ikon aiki don na'urorin. Dole ne a cire Jumpers J1 da J2.
SHIGA KYAUTA 1 - INPUT 8 IN, GND	Daga buɗaɗɗe da/ko buɗaɗɗen shigar da abubuwan shigar da ruwa mai tarawa (buƙatar fita maɓallan, fita PIRs, da sauransu.)
FITOWA TA 1- Fitarwa 8 NC, C, NO, COM	12VDC zuwa 24VDC abubuwan da aka sarrafa mai faɗakarwa ana ƙididdige su a 2.5A. Maximal3FDV - 10.0-13.2VDC 0 4.6A ko 20.19-26.4VDC 0 5.2A. Maximal5FDV - 10.03-13.2VDC 0 8.6A. Maximal7FDV - 20.17-26.4VDC 0 9.2A. Rashin-Safe [NC tabbatacce (+) & COM Korau (—)], Rashin Amintacce [NO tabbatacce (+) & COM Negative (-)], Fitarwa na taimako [C tabbatacce (+) & COM Korau (-)]. Lokacin amfani da wutar lantarki AC baya buƙatar kiyaye polarity. Lambobin sadarwa suna nunawa a cikin yanayin da ba a kunna ba.
FACP INTERFACE T, + INPUT -	Wuta Ƙararrawa Interface yana jawo shigarwa daga FACP. Ana iya buɗe abubuwan shigar da ƙara a kullum, kullum rufe daga FACP sigina fitarwa kewaye (Figs. 5-9, shafi. 11).
FACP INTERFACE NC, C, BA	Form "C" tuntuɓi mai lamba @ 1A 28VDC don rahoton ƙararrawa.

Takaddun Takaddun Takaddun Batir na Hukumar Samar da Wuta:

Baturi	Saukewa: FDV3	Saukewa: FDV5	Saukewa: FDV7
7AH	Minti 10/6A	Minti 5/10A	Minti 5/10A
12AH	Minti 30/6A	Minti 30/10A	Minti 30/10A
40AH	Sama da Awa 4/6A	Sama da Awa 2/10A	Sama da Awa 2/10A
65AH	Sama da Awa 4/6A	Sama da Awa 4/10A	Sama da Awa 4/10A

Fitar da Wutar Lantarki Voltage Saituna:

Hannun Hannun Aikace-aikacen Mai Gudanar da Wuta (na kowane ACM8CB):

Hoto 3 - Maximal3FDV, Maximal5FDV, da Maximal7FDV

HANKALI: Lokacin da aka saita allon samar da wutar lantarki don 12VDC yi amfani da baturi ɗaya kawai (1) 12VDC.
Kiyaye iyakataccen wayoyi daban da mara iyaka.
Yi amfani da tazara mafi ƙarancin 0.25 inci.
12AH batura masu caji sune manyan batura waɗanda zasu iya dacewa da wannan shingen. Dole ne a yi amfani da shingen baturi na waje idan ana amfani da batir 40AH ko 65AH.

Abubuwan Buƙatun Waya Masu Iyakancin Wutar NEC:

Wayoyin da'ira mai iyaka da mara ƙarfi dole ne su kasance cikin rabuwa a cikin majalisar. Duk wayoyi masu iyakacin wutar lantarki dole ne su kasance aƙalla 0.25” nesa da kowane wayoyi marasa iyaka. Bugu da ƙari, duk na'urorin da'irar da ba ta da iyaka da wutar lantarki dole ne su shiga kuma su fita daga majalisar ta hanyoyi daban-daban.
Daya irin wannan example na wannan aka nuna a kasa. Takamammen aikace-aikacen ku na iya buƙatar yin amfani da ƙwanƙwasawa daban-daban. Ana iya amfani da kowane ƙwanƙwasa magudanar ruwa. Don aikace-aikacen iyakantaccen wutar lantarki amfani da magudanar ruwa zaɓi ne. Dole ne a yi duk hanyoyin haɗin yanar gizo ta amfani da ma'auni mai dacewa CM ko FPL waya mai jaki (ko madaidaicin daidai).
Dole ne a ɗora shingen baturi na zaɓi na UL da aka jera kusa da wutar lantarki ta hanyoyin wayoyi na Class 1.
Don shigarwa na Kanada yi amfani da wayoyi masu kariya don duk haɗin gwiwa.
Lura: Koma zuwa zane mai sarrafa waya a ƙasa don hanyar da ta dace don shigar da waya mai jakin CM ko FPL (Hoto 4a).

Zane-zane na Ƙoƙwalwar FACP:

Hoto 5 shigarwar juyar da polarity daga fitarwa na sigina na FACP (an yi la'akari da polarity a yanayin ƙararrawa):	Hoto 6 Akan Buɗewa: Ba-Latching FACP shigar da ƙara:
Hoto 7 A kullum Buɗe shigar da shigar FACP Latching tare da sake saiti (UL ba ta kimanta wannan fitarwa ba):	Hoto 8 Akan Rufe: Ba-Latching FACP shigar da fararwa:
Hoto 9 Akan Rufe: Latching shigarwar FACP mai jawo tare da sake saiti (UL bai kimanta wannan fitarwa ba):

Matsakaicin Rukuni (H x W x D kimanin):
26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm)

Altronix baya da alhakin kowane kuskuren rubutu.
140 58th Street, Brooklyn, New York 11220 USA | waya: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Garanti na rayuwa
IMaximal3FDV/5FDV/7FDV Series
H13 ku
Jagoran Shigarwa Maximal3FDV/5FDV/7FDV Series (PTC).

Takardu / Albarkatu

Altronix Maximal7FDV Masu Kula da Wutar Lantarki [pdf] Jagoran Jagora Maximal7FDV Masu Kula da Wutar Lantarki, Maximal7FDV, Masu Gudanar da Wuta, Masu Sarrafa Wuta, Masu Sarrafa

Magana

• Manual mai amfani