ESP32-PICO-V3-02 IoT Development Module

“

Спецификације

• СоЦ: ESP32-PICO-V3-02 240 MHz dual-core,
  Wi-Fi, 2 MB PSRAM, 8 MB Flash
• Улазни волtage: 5 В @ 500 мА
• Интерфејс: Type-C x 1, GROVE (I2C + I/O +
  UART) x 1
• ЛЦД екран: 1.14 inch, 135 x 240 Color TFT
  LCD, ST7789V2
• микрофон: СПМ1423
• Дугмад: User buttons x 3, Green LED x 1
  (non-programmable, sleep indicator), Red LED x 1 (shares control
  pin G19 with IR LED emitter)
• РТЦ: БМ8563
• Зујалица: On-board passive buzzer
• ИМУ: МПУ6886
• Антена: 2.4 G 3D antenna
• External Pins: G0, G25/G26, G36, G32, G33
• батерија: 200 mAh @ 3.7 V, inside
• Радна температура:
• Прилог: Пластика (ПЦ)

Упутства за употребу производа

Припрема

1. Погледајте на M5Burner
   туториал to complete the firmware flashing tool download.
2. Download the corresponding firmware from the provided
   линк.

Инсталација УСБ драјвера

Install the USB driver required for the device.

Избор порта

Connect the device to the computer via a USB cable. After driver
installation, select the corresponding device port in M5Burner.

Бурн

Click on “Burn” to start the flashing process.

ФАК

Q1: Why is my M5StickC Plus2 black screen/won’t boot?

решење: Use M5Burner to flash the official
Factory Firmware.

Q2: Why does it only work for 3 hours? Why does it charge to
100% in 1 minute and turn off when removing the charging
кабл?

решење: Flash back the official firmware as
using unofficial firmware can void warranty and cause
нестабилност.

“`

M5StickC Plus2 Operation Guidance
Фабрички фирмвер
When the device encounters operational issues, you can try re-flashing the factory firmware to check if there is any hardware malfunction. Refer to the following tutorial. Use the M5Burner firmware flashing tool to flash the factory firmware onto the device.

ФАК
Q1: Why is my M5StickC Plus2 black screen/won’t boot?
Solutions: M5Burner Burn official Factory Firmware”M5StickCPlus2 UserDemo”

Q2: Why it working time only 3 hours? Why does it 100% charge in 1 minute, remove the charging cable it will turn off?

Solutions:”Bruce for StickC plus2″This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution. Please burn back official firmware.

1. Припрема
o Refer to the M5Burner tutorial to complete the firmware flashing tool download, and then refer to the image below to download the corresponding firmware.
Download link: https://docs.m5stack.com/en/uiflow/m5burner/intro
2. Инсталација УСБ драјвера
Driver Installation Tip Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver. CH9102_VCP_SER_Windows https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe CH9102_VCP_SER_MacOS v1.7 https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip Port Selection on MacOS On MacOS, there may be two available ports. When using them, please select the port named wchmodem.

3. Port Selection
Connect the device to the computer via a USB cable. After the driver installation is complete, you can select the corresponding device port in M5Burner.
4. Burn
Click “Burn” to start the flashing process.

StickC-Plus2
SKU:K016-P2
1/13 | Update Time: 2025-07-31

Опис
StickC-Plus2 is the iterative version of StickC-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240. The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules. This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Туториал
УИФлов
This tutorial will introduce how to control the StickC-Plus2 device through the UIFlow graphical programming platform.
UiFlow2
This tutorial will introduce how to control the StickC-Plus2 device through the UiFlow2 graphical programming platform.
Ардуино ИДЕ
This tutorial will introduce how to program and control the StickC-Plus2 device using the Arduino IDE.
2/13 | Update Time: 2025-07-31

Напомена
Port Not Recognized When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure: disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Карактеристике
Based on ESP32-PICO-V3-02 with Wi-Fi support Built-in 3-axis accelerometer and 3-axis gyroscope Integrated IR emitter Built-in RTC Integrated microphone User buttons, 1.14-inch LCD, power/reset button 200 mAh Li-ion battery Expansion connector Integrated passive buzzer Wearable & mountable Development Platform
UiFlow1 UiFlow2 Arduino IDE ESP-IDF PlatformIO
Укључује
1 x StickC-Plus2
Апликације
Wearable devices IoT controller STEM education DIY projects Smart-home devices
3/13 | Update Time: 2025-07-31

Спецификације

Спецификација

Параметар

СоЦ

ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash

Улазни волtage

5 В @ 500 мА

Интерфејс

Type-C x 1, GROVE (I2C + I/O + UART) x 1

ЛЦД екран

1.14 inch, 135 x 240 Color TFT LCD, ST7789V2

Микрофон

СПМ1423

Дугмад

User buttons x 3

Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR LED
emitter)

РТЦ

БМ8563

Зујалица

On-board passive buzzer

ИМУ

МПУ6886

Антена

2.4 G 3D antenna

Ектернал Пинс

G0, G25/G26, G36, G32, G33

Батерија

200 mAh @ 3.7 V, inside

Радна темп

0 ~ 40 °Ц

Енцлосуре

Пластика (ПЦ)

Величина производа

48.0 к 24.0 к 13.5 мм

Тежина производа

16.7 г

Величина пакета

104.4 к 65.0 к 18.0 мм

Бруто тежина

26.3 г

Упутство за рад

4/13 | Update Time: 2025-07-31

Укључивање/искључивање
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again. Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Сцхематицс
StickC-Plus2 Schematics PDF
5/13 | Update Time: 2025-07-31

6/13 | Update Time: 2025-07-31

PinMap

Red LED & IR Emitter | Button A | Button B | Buzzer

ESP32-PICO-V3-02 IR Emitter & Red LED
Button A Button B Button C Passive Buzzer

GPIO19 IR emitter & Red LED pin

GPIO37 Button A

GPIO39 Button B

GPIO35 Button C

GPIO2 Buzzer

ТФТ екран у боји
Driver IC: ST7789V2 Resolution: 135 x 240

7/13 | Update Time: 2025-07-31

ESP32-PICO-V3-02 TFT Display

G15 TFT_MOSI

G13 TFT_CLK

G14 TFT_DC

G12 TFT_RST

G5 TFT_CS

G27 TFT_BL

Microphone MIC (SPM1423)

ESP32-PICO-V3-02

G0

MIC SPM1423

ЦЛК

G34 DATA

6-Axis IMU (MPU6886) & RTC BM8563

ESP32-PICO-V3-02 IMU MPU6886 BM8563 IR Emitter Red LED

G22 SCL SCL

G21 SDA SDA

Г19
ТКС ТКС

ХИ2.0-4П
HY2.0-4P PORT.CUSTOM

Блацк ГНД

Црвени

Жута

Бела

5V

Г32

Г33

Величина модела

8/13 | Update Time: 2025-07-31

Датасхеетс
ESP32-PICO-V3-02 ST7789V2 BM8563 MPU6886 SPM1423
Софтварес
Ардуино
StickC-Plus2 Arduino Quick Start StickC-Plus2 Library StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Quick Start
UiFlow2

9/13 | Update Time: 2025-07-31

StickC-Plus2 UiFlow2 Quick Start
ПлатформИО
[[eennvv::mm55ssttaacckk–ssttiicckkcc–pplluuss22]] ppllaattffoorrmm == eesspprreessssiiff3322@@66..77..00 bbooaarrdd == mm55ssttiicckk–cc ffrraammeewwoorrkk == aarrdduuiinnoo uuppllooaadd__ssppeeeedd == 11550000000000 mmoonniittoorr__ssppeeeedd == 111155220000 bbuuiilldd__ffllaaggss ==
–DDBBOOAARRDD__HHAASS__PPSSRRAAMM –mmffiixx–eesspp3322–ppssrraamm–ccaacchhee–iissssuuee –DDCCOORREE__DDEEBBUUGG__LLEEVVEELL==55 lliibb__ddeeppss == MM55UUnniiffiieedd==hhttttppss::////ggiitthhuubb..ccoomm//mm55ssttaacckk//MM55UUnniiffiieedd

УСБ драјвер
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth. If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.

Driver Name CH9102_VCP_SER_Windows CH9102_VCP_SER_MacOS v1.7

Supported Chip CH9102 CH9102

Download Download Download

macOS Port Selection Two serial ports may appear on macOS. Please select the port named wchmodem.

Easyloader
EasyLoader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.

Easyloader FactoryTest for Windows

Download download

Белешка /

Остало

10/13 | Update Time: 2025-07-31

StickC-Plus2 Restore Factory Firmware Guide
Видео
StickC-Plus2 Feature Introduction StackC Plus2 .mp4
Промена верзије

Release Date /
2021-12
2023-12

Промените опис
First release Added sleep and wake-up function, version updated to v1.1 Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02,
different power-on/off method, version v2

Note / / /

Поређење производа

Хардверске разлике

11/13 | Update Time: 2025-07-31

Назив производа

Power SoC
Менаџмент

StickC-Plus ESP32-PICO-D4

АКСПКСНУМКС

ESP32-PICO-

StickC-Plus2

/

ВКСНУМКС-КСНУМКС

Капацитет батерије

Меморија

USB-UART Chip

Боја

120 мАх

520 KB SRAM + 4 MB Flash

ЦХ522

Црвена поморанџа

200 мАх

2 MB PSRAM + 8 MB Flash

ЦХ9102

Оранге

Pin Differences

Product IR
Име
M5STICKC G9
ПЛУС
M5STICKC G19
ПЛУС2

Батерија

BUTTON C

ЛЕД

ТФТ

BUTTON A BUTTON B

ХОЛД

Волtage

(WAKE)

Детецт

MOSI (G15)

CLK (G13)

Г10

DC (G23)

Г37

RST (G18)

Regular G39
дугме

/

Via AXP192

CS (G5)

MOSI (G15)

CLK (G13)

Г19

DC (G14)

Г37

Г39

Г35

G4

Г38

RST (G12)

CS (G5)

Power On/Off Differences

12/13 | Update Time: 2025-07-31

Назив производа

Повер Он

Повер Офф

StickC-Plus

Press reset button (BUTTON C) for at least 2 s

Press reset button (BUTTON C) for at least 6 s

Press “BUTTON C” for more than 2 s, or Without USB power, press “BUTTON C” for more than 6 s,

StickCPlus2

wake via RTC IRQ. After wake-up, set

or set HOLD (GPIO4)=0 in the program to power off. With

HOLD (G4)=1 in the program to keep

USB connected, pressing “BUTTON C” for more than 6 s

power on, otherwise the device will shut will turn off the screen and enter sleep, but not a full power-

down again.

искључено.

Because StickC-Plus2 removes the PMIC AXP192, the power-on/off method differs from previous versions. As mentioned at the beginning of this document, the operation is largely similar, but the supported libraries will differ. Wi-Fi and IR signal strength have both been improved compared to the previous model.

13/13 | Update Time: 2025-07-31

Документи / Ресурси

M5STACK ESP32-PICO-V3-02 IoT Development Module [пдф] Упутство за кориснике ESP32-PICO-V3-02 IoT Development Module, ESP32-PICO-V3-02, IoT Development Module, Development Module, Module

Референце

• Упутство за употребу