ESP32-PICO-V3-02 IoT Development Module

“

Specificații

• SoC: ESP32-PICO-V3-02 240 MHz dual-core,
  Wi-Fi, 2 MB PSRAM, 8 MB Flash
• Vol. De intraretage: 5 V @ 500 mA
• Interfata: Type-C x 1, GROVE (I2C + I/O +
  UART) x 1
• Ecran LCD: 1.14 inch, 135 x 240 Color TFT
  LCD, ST7789V2
• Microfon: SPM1423
• Butoane: User buttons x 3, Green LED x 1
  (non-programmable, sleep indicator), Red LED x 1 (shares control
  pin G19 with IR LED emitter)
• RTC: BM8563
• Buzzer: On-board passive buzzer
• IMU: MPU6886
• Antenă: 2.4 G 3D antenna
• External Pins: G0, G25/G26, G36, G32, G33
• Baterie: 200 mAh @ 3.7 V, inside
• Temperatura de funcționare:
• Carcasă: Plastic (PC)

Instrucțiuni de utilizare a produsului

Pregătirea

1. Consultați M5Burner
   tutorial to complete the firmware flashing tool download.
2. Download the corresponding firmware from the provided
   legătură.

Instalare driver USB

Install the USB driver required for the device.

Selectarea portului

Connect the device to the computer via a USB cable. After driver
installation, select the corresponding device port in M5Burner.

Arde

Click on “Burn” to start the flashing process.

FAQ

Q1: Why is my M5StickC Plus2 black screen/won’t boot?

Soluţie: Use M5Burner to flash the official
Factory Firmware.

Q2: Why does it only work for 3 hours? Why does it charge to
100% in 1 minute and turn off when removing the charging
cablu?

Soluţie: Flash back the official firmware as
using unofficial firmware can void warranty and cause
instabilitate.

„`

M5StickC Plus2 Operation Guidance
Firmware din fabrică
When the device encounters operational issues, you can try re-flashing the factory firmware to check if there is any hardware malfunction. Refer to the following tutorial. Use the M5Burner firmware flashing tool to flash the factory firmware onto the device.

FAQ
Q1: Why is my M5StickC Plus2 black screen/won’t boot?
Solutions: M5Burner Burn official Factory Firmware”M5StickCPlus2 UserDemo”

Q2: Why it working time only 3 hours? Why does it 100% charge in 1 minute, remove the charging cable it will turn off?

Solutions:”Bruce for StickC plus2″This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution. Please burn back official firmware.

1. Pregătire
o Refer to the M5Burner tutorial to complete the firmware flashing tool download, and then refer to the image below to download the corresponding firmware.
Download link: https://docs.m5stack.com/en/uiflow/m5burner/intro
2. Instalare driver USB
Driver Installation Tip Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver. CH9102_VCP_SER_Windows https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe CH9102_VCP_SER_MacOS v1.7 https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip Port Selection on MacOS On MacOS, there may be two available ports. When using them, please select the port named wchmodem.

3. Port Selection
Connect the device to the computer via a USB cable. After the driver installation is complete, you can select the corresponding device port in M5Burner.
4. Burn
Click “Burn” to start the flashing process.

StickC-Plus2
SKU:K016-P2
1/13 | Update Time: 2025-07-31

Descriere
StickC-Plus2 is the iterative version of StickC-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240. The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules. This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Tutorial
UIFlow
This tutorial will introduce how to control the StickC-Plus2 device through the UIFlow graphical programming platform.
UiFlow2
This tutorial will introduce how to control the StickC-Plus2 device through the UiFlow2 graphical programming platform.
Arduino IDE
This tutorial will introduce how to program and control the StickC-Plus2 device using the Arduino IDE.
2/13 | Update Time: 2025-07-31

Nota
Port Not Recognized When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure: disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Caracteristici
Based on ESP32-PICO-V3-02 with Wi-Fi support Built-in 3-axis accelerometer and 3-axis gyroscope Integrated IR emitter Built-in RTC Integrated microphone User buttons, 1.14-inch LCD, power/reset button 200 mAh Li-ion battery Expansion connector Integrated passive buzzer Wearable & mountable Development Platform
UiFlow1 UiFlow2 Arduino IDE ESP-IDF PlatformIO
Include
1 x StickC-Plus2
Aplicații
Wearable devices IoT controller STEM education DIY projects Smart-home devices
3/13 | Update Time: 2025-07-31

Specificații

Caietul de sarcini

Parametru

SoC

ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash

Vol. De intraretage

5 V @ 500 mA

Interfață

Type-C x 1, GROVE (I2C + I/O + UART) x 1

Ecran LCD

1.14 inch, 135 x 240 Color TFT LCD, ST7789V2

Microfon

SPM1423

Butoane

User buttons x 3

Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR LED
emițător)

RTC

BM8563

Buzzer

On-board passive buzzer

IMU

MPU6886

Antenă

2.4 G 3D antenna

Pinuri externe

G0, G25/G26, G36, G32, G33

Baterie

200 mAh @ 3.7 V, inside

Temp. de operare

0 ~ 40 °C

Incinta

Plastic (PC)

Dimensiunea produsului

48.0 x 24.0 x 13.5 mm

Greutatea produsului

16.7 g

Dimensiunea pachetului

104.4 x 65.0 x 18.0 mm

Greutate brută

26.3 g

Instrucțiuni de operare

4/13 | Update Time: 2025-07-31

Pornire/Oprire
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again. Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Scheme
StickC-Plus2 Schematics PDF
5/13 | Update Time: 2025-07-31

6/13 | Update Time: 2025-07-31

PinMap

Red LED & IR Emitter | Button A | Button B | Buzzer

ESP32-PICO-V3-02 IR Emitter & Red LED
Button A Button B Button C Passive Buzzer

GPIO19 IR emitter & Red LED pin

GPIO37 Button A

GPIO39 Button B

GPIO35 Button C

GPIO2 Buzzer

Ecran TFT color
Driver IC: ST7789V2 Resolution: 135 x 240

7/13 | Update Time: 2025-07-31

ESP32-PICO-V3-02 TFT Display

G15 TFT_MOSI

G13 TFT_CLK

G14 TFT_DC

G12 TFT_RST

G5 TFT_CS

G27 TFT_BL

Microphone MIC (SPM1423)

ESP32-PICO-V3-02

G0

MIC SPM1423

CLK

G34 DATA

6-Axis IMU (MPU6886) & RTC BM8563

ESP32-PICO-V3-02 IMU MPU6886 BM8563 IR Emitter Red LED

G22 SCL SCL

G21 SDA SDA

G19
TX TX

HY2.0-4P
HY2.0-4P PORT.CUSTOM

GND negru

Roşu

Galben

Alb

5V

G32

G33

Dimensiunea modelului

8/13 | Update Time: 2025-07-31

Fișe de date
ESP32-PICO-V3-02 ST7789V2 BM8563 MPU6886 SPM1423
Software-uri
Arduino
StickC-Plus2 Arduino Quick Start StickC-Plus2 Library StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Quick Start
UiFlow2

9/13 | Update Time: 2025-07-31

StickC-Plus2 UiFlow2 Quick Start
PlatformIO
[[eennvv::mm55ssttaacckk–ssttiicckkcc–pplluuss22]] ppllaattffoorrmm == eesspprreessssiiff3322@@66..77..00 bbooaarrdd == mm55ssttiicckk–cc ffrraammeewwoorrkk == aarrdduuiinnoo uuppllooaadd__ssppeeeedd == 11550000000000 mmoonniittoorr__ssppeeeedd == 111155220000 bbuuiilldd__ffllaaggss ==
–DDBBOOAARRDD__HHAASS__PPSSRRAAMM –mmffiixx–eesspp3322–ppssrraamm–ccaacchhee–iissssuuee –DDCCOORREE__DDEEBBUUGG__LLEEVVEELL==55 lliibb__ddeeppss == MM55UUnniiffiieedd==hhttttppss::////ggiitthhuubb..ccoomm//mm55ssttaacckk//MM55UUnniiffiieedd

Driver USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth. If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.

Driver Name CH9102_VCP_SER_Windows CH9102_VCP_SER_MacOS v1.7

Supported Chip CH9102 CH9102

Download Download Download

macOS Port Selection Two serial ports may appear on macOS. Please select the port named wchmodem.

Easyloader
EasyLoader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.

Easyloader FactoryTest for Windows

Download download

Notă /

Alte

10/13 | Update Time: 2025-07-31

StickC-Plus2 Restore Factory Firmware Guide
Video
StickC-Plus2 Feature Introduction StackC Plus2 .mp4
Schimbarea versiunii

Release Date /
2021-12
2023-12

Schimbați descrierea
First release Added sleep and wake-up function, version updated to v1.1 Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02,
different power-on/off method, version v2

Note / / /

Comparație de produse

Diferențe hardware

11/13 | Update Time: 2025-07-31

Numele produsului

Power SoC
management

StickC-Plus ESP32-PICO-D4

AXP192

ESP32-PICO-

StickC-Plus2

/

V3-02

Capacitatea bateriei

Memorie

USB-UART Chip

Culoare

120 mAh

520 KB SRAM + 4 MB Flash

CH522

Redorange

200 mAh

2 MB PSRAM + 8 MB Flash

CH9102

Portocale

Pin Differences

Product IR
Nume
M5STICKC G9
PLUS
M5STICKC G19
PLUS2

Baterie

BUTONUL C

LED

TFT

BUTTON A BUTTON B

ȚINE

Voltage

(WAKE)

Detecta

MOSI (G15)

CLK (G13)

G10

DC (G23)

G37

RST (G18)

Regular G39
buton

/

Via AXP192

CS (G5)

MOSI (G15)

CLK (G13)

G19

DC (G14)

G37

G39

G35

G4

G38

RST (G12)

CS (G5)

Power On/Off Differences

12/13 | Update Time: 2025-07-31

Numele produsului

Pornire

Oprire

StickC-Plus

Press reset button (BUTTON C) for at least 2 s

Press reset button (BUTTON C) for at least 6 s

Press “BUTTON C” for more than 2 s, or Without USB power, press “BUTTON C” for more than 6 s,

StickCPlus2

wake via RTC IRQ. After wake-up, set

or set HOLD (GPIO4)=0 in the program to power off. With

HOLD (G4)=1 in the program to keep

USB connected, pressing “BUTTON C” for more than 6 s

power on, otherwise the device will shut will turn off the screen and enter sleep, but not a full power-

down again.

oprit.

Because StickC-Plus2 removes the PMIC AXP192, the power-on/off method differs from previous versions. As mentioned at the beginning of this document, the operation is largely similar, but the supported libraries will differ. Wi-Fi and IR signal strength have both been improved compared to the previous model.

13/13 | Update Time: 2025-07-31

Documente/Resurse

M5STACK ESP32-PICO-V3-02 IoT Development Module [pdfGhid de utilizare ESP32-PICO-V3-02 IoT Development Module, ESP32-PICO-V3-02, IoT Development Module, Development Module, Module

Referințe

• Manual de utilizare