Gwida għall-Operazzjoni tal-M5StickC Plus2
Firmware tal-Fabbrika
Meta l-apparat jiltaqa' ma' problemi operattivi, tista' tipprova terġa' tifflaxxja l-firmware tal-fabbrika biex tiċċekkja jekk hemmx xi malfunzjoni fil-hardware. Irreferi għat-tutorja li ġejja. Uża l-għodda tal-flaxxjar tal-firmware M5Burner biex tifflaxxja l-firmware tal-fabbrika fuq l-apparat.
FAQ
M1: Għaliex l-iskrin tal-M5StickC Plus2 tiegħi huwa iswed/ma jridx jibbutja?
Soluzzjonijiet: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
M2: Għaliex idum jaħdem biss 3 sigħat? Għaliex jiċċarġja 100% f'minuta, neħħi l-kejbil tal-iċċarġjar u jintefa?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Jekk jogħġbok irreġistra l-firmware uffiċjali.
Preparazzjoni
- Irreferi għat-tutorja tal-M5Burner biex tlesti t-tniżżil tal-għodda tal-flaxxjar tal-firmware, u mbagħad irreferi għall-immaġni hawn taħt biex tniżżel il-firmware korrispondenti.
Niżżel il-link: https://docs.m5stack.com/en/uiflow/m5burner/intro
Installazzjoni tas-Sewwieq USB
Ħjiel għall-Installazzjoni tas-Sewwieq
Ikklikkja l-link t'hawn taħt biex tniżżel is-sewwieq li jaqbel mas-sistema operattiva tiegħek. Il-pakkett tas-sewwieq għas-CP34X (għall-verżjoni CH9102) jista' jitniżżel u jiġi installat billi tagħżel il-pakkett tal-installazzjoni li jikkorrispondi mas-sistema operattiva tiegħek. Jekk tiltaqa' ma' problemi bit-tniżżil tal-programm (bħal timeout jew żbalji "Failed to write to target RAM"), ipprova erġa' installa s-sewwieq tal-apparat.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Għażla tal-Port fuq MacOS
Fuq MacOS, jista' jkun hemm żewġ portijiet disponibbli. Meta tużahom, jekk jogħġbok agħżel il-port bl-isem wchmodem.
Għażla tal-Port
Qabbad l-apparat mal-kompjuter permezz ta' kejbil USB. Wara li titlesta l-installazzjoni tad-drajver, tista' tagħżel il-port tal-apparat korrispondenti f'M5Burner.
Ħruq
Ikklikkja “Ħruq” biex tibda l-proċess tal-flashing.
StickC-Plus2
SKU:K016-P2
Deskrizzjoni
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Tutorja
UIFlow
Dan it-tutorja se jintroduċi kif tikkontrolla l-apparat StickC-Plus2 permezz tal-pjattaforma ta' programmar grafika UIFlow.
UiFlow2
Dan it-tutorja se jintroduċi kif tikkontrolla l-apparat StickC-Plus2 permezz tal-pjattaforma ta' programmar grafika UiFlow2.
Arduino IDE
Dan it-tutorja se jintroduċi kif tipprogramma u tikkontrolla l-apparat StickC-Plus2 bl-użu tal-Arduino IDE.
Nota
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Karatteristiċi
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Mikrofonu integrat
- User buttons, 1.14-inch LCD, power/reset button
- 200 mAh Li-ion batterija
- Konnettur ta 'espansjoni
- Integrated passive buzzer
- Wearable & mountable
- Pjattaforma ta' Żvilupp
- UiFlow1
- UiFlow2
- Arduino IDE
- ESP-IDF
- PlatformIO
Jinkludi
- 1 x StickC-Plus2
Applikazzjonijiet
- Apparat li jintlibes
- IoT controller
- STEM education
- Proġetti DIY
- Apparat tad-dar intelliġenti
Speċifikazzjonijiet
| Speċifikazzjoni | Parametru |
| SoC | ESP32-PICO-V3-02 240 MHz b'żewġ qlub, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Input Voltage | 5 V @ 500 mA |
| Interface | Tip-Ċ x 1, GROVE (I2C + I/O + UART) x 1 |
| Skrin LCD | 1.14 pulzier, 135 x 240 TFT LCD bil-kulur, ST7789V2 |
| Mikrofonu | SPM1423 |
| Buttuni | Buttuni tal-utent x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Buzzer | Buzzer passiv abbord |
| IMU | MPU6886 |
| Antenna | Antenna 2.4 G 3D |
| Pinnijiet Esterni | G0, G25/G26, G36, G32, G33 |
| Batterija | 200 mAh @ 3.7 V, ġewwa |
| Temp operattiv | 0 ~ 40 °C |
| Egħluq | Plastik (PC) |
| Daqs tal-Prodott | 48.0 x 24.0 x 13.5mm |
| Piż tal-Prodott | 16.7 g |
| Daqs tal-Pakkett | 104.4 x 65.0 x 18.0mm |
| Piż Gross | 26.3 g |
Istruzzjonijiet ta' Operazzjoni
Qawwa mixgħul/mitfi
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Skematika
PDF tal-Iskemi ta' StickC-Plus2
Pin Pin
LED Aħmar & Emittent IR | Buttuna A | Buttuna B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Buttuna A | Buttuna A | ||||
| Buttuna B | Buttuna B | ||||
| Buttuna Ċ | Buttuna Ċ | ||||
| Buzzer passiv | Buzzer |
Display TFT bil-kulur
Driver IC: ST7789V2
Riżoluzzjoni: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Display TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Mikrofonu MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DEJTA |
IMU ta' 6 Assi (MPU6886) u RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Emitter IR | TX | ||
| LED aħmar | TX |
HY2.0-4P
| HY2.0-4P | Iswed | Aħmar | Isfar | Abjad |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Daqs tal-Mudell
Datasheets
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU6886
SPM1423
Softwares
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
Bidu Mgħaġġel ta' StickC-Plus2 UiFlow1
UiFlow2
Bidu Mgħaġġel ta' StickC-Plus2 UiFlow2
PlatformIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
framework = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Sewwieq USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Isem tas-sewwieq | Supported Chip | Niżżel |
| CH9102_VCP_SER_Windows | CH9102 | Niżżel |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Niżżel |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Niżżel | Nota |
| Factory Test for Windows | niżżel | / |
Oħrajn
Gwida għar-Restawr tal-Firmware tal-Fabbrika ta' StickC-Plus2
Video
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Bidla fil-Verżjoni
| Data ta' Rilaxx | Deskrizzjoni tal-Bidla | Nota |
| / | L-ewwel rilaxx | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Tqabbil tal-Prodott
Differenzi tal-Ħardwer
| Prodott Isem |
SoC | Ġestjoni tal-Enerġija | Kapaċità tal-batterija | Memorja | Ċippa USB-UART | Kulur |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Oranġjo |
Differenzi tal-Pin
| Isem tal-Prodott | IR | LED | TFT | BUTTONA A | BUTTONA B | BUTTUNA Ċ (QAJMA) |
ŻOMM | Batterija Voltage Issib |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Regolari buttuna |
/ | Permezz tal-AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Differenzi fil-Mixgħul/Mitfi
| Prodott Isem | Qawwa Mixgħul | Qawwa Mitfi |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Peress li StickC-Plus2 ineħħi l-PMIC AXP192, il-metodu ta' mixgħul/mitfi huwa differenti mill-verżjonijiet preċedenti. Kif imsemmi fil-bidu ta' dan id-dokument, l-operazzjoni hija fil-biċċa l-kbira simili, iżda l-libreriji appoġġjati se jkunu differenti. Is-saħħa tas-sinjal Wi-Fi u IR it-tnejn tjiebu meta mqabbla mal-mudell preċedenti.
Dokumenti / Riżorsi
 |
Modulu ta' Żvilupp tal-IoT M5STACK ESP32-PICO-V3-02 [pdfGwida għall-Utent ESP32-PICO-V3-02 Modulu ta' Żvilupp tal-IoT, ESP32-PICO-V3-02, Modulu ta' Żvilupp tal-IoT, Modulu ta' Żvilupp, Modulu |