ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer
“
Informacioni i produktit
Specifikimet
The ED-IPC2500 is a 5G industrial computer based on the
Raspberry Pi CM4. It offers different RAM and eMMC specifications
based on user requirements. The device includes interfaces such as
HDMI, USB 2.0, and Ethernet, supporting network access via Wi-Fi,
Ethernet, and 5G. Additional features include a supercapacitor
backup power supply (optional), RTC, Watch Dog, EEPROM, and
encryption chip for enhanced usability and reliability. Primarily
used in industrial control and IoT fields.
Udhëzimet e përdorimit të produktit
1. Hardware Mbiview
The ED-IPC2500 is equipped with various interfaces for
connectivity, including HDMI, USB 2.0, and Ethernet. It also
supports network access via Wi-Fi, Ethernet, and 5G.
2. Paneli perballe
The front panel features indicators for power status, 5G signal
status, system status, and user-defined status. It also includes a
DC input for power supply.
3. Paneli i pasmë
The rear panel includes ports for 5G antenna connection, Micro
SD card slot (reserved function), Nano SIM card slot for 5G access,
Wi-Fi/BT antenna port (optional), Micro USB port for flashing to
eMMC, and additional 5G antenna port.
4. Paneli anësor
The side panel consists of a reset button for device restart,
USB 2.0 ports for peripheral connections, HDMI port for display
connectivity, and multiple 5G antenna ports.
The device includes a hidden reset button that can be pressed to
rinisni pajisjen.
6. Treguesi
The device features indicators for power status, 5G signal
status, system status, and user-defined status.
Pyetjet e bëra më shpesh (FAQ)
Q: What are the main applications of the ED-IPC2500?
A: The ED-IPC2500 is mainly used in industrial control and
Internet of Things (IoT) fields due to its reliability and ease of
përdorni.
Pyetje: Si mund ta rivendos pajisjen?
A: Press the hidden reset button located on the side panel to
rinisni pajisjen.
“`
ED-IPC2500
Manuali i Përdoruesit
nga EDA Technology Co., Ltd ndërtuar: 2025-08-01
ED-IPC2500
1 Manual për Pajisjet
Ky kapitull prezanton produktinview, lista e paketimit, pamja, butoni, treguesi dhe ndërfaqja.
1.1 Mbiview
The ED-IPC2500 is a 5G industrial computer based on the Raspberry Pi CM4. Depending on the application scenario and user requirements, computer systems with different RAM and eMMC specifications can be selected.
· RAM options include 1GB, 2GB, 4GB, and 8GB. · eMMC options include 8GB, 16GB, and 32GB.
The ED-IPC2500 provides commonly used interfaces such as HDMI, USB 2.0, and Ethernet. It supports network access via Wi-Fi, Ethernet, and 5G. The integration of a supercapacitor backup power supply (optional), RTC (Real-Time Clock), Watch Dog, EEPROM, and an encryption chip enhances the product’s ease of use and reliability. It is mainly used in industrial control and Internet of Things (IoT) fields.
1.2 Lista e paketimit
· 1 x ED-IPC2500 Unit · [WiFi/BT Version – optional] 1 x 2.4GHz/5GHz Wi-Fi/BT Antenna
1.3 Pamja e jashtme
Prezantimi i funksioneve dhe përkufizimeve të ndërfaqeve në çdo panel.
1.3.1 Paneli i përparmë
Ky seksion prezanton funksionet dhe përkufizimet e panelit të përparmë.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
NR.
Përkufizimi i funksionit
1
1 x tregues i kuq i energjisë, i cili përdoret për të kontrolluar statusin e ndezjes dhe fikjes së pajisjes.
2
1 x tregues jeshil 5G, i cili përdoret për të kontrolluar statusin e sinjalit 5G.
1 x DC input, 2-Pin 3.5mm spacing phoenix terminals with screw holes. It supports 9V~36V input, the signal 3
is defined as VIN+/GND.
3 × 1000M Ethernet interfaces (ETH0ETH2), RJ45 connector with LED indicators, 10/100/1000M auto4
sensing interfaces for Ethernet connection.
5
1 x tregues i statusit të sistemit jeshil, i cili përdoret për të kontrolluar statusin e punës së pajisjes.
6
1 x tregues i gjelbër i përdoruesit, përdoruesi mund të personalizojë një status sipas aplikacionit aktual.
1.3.2 Paneli i pasmë
Ky seksion prezanton ndërfaqet dhe përkufizimet e panelit të pasmë.
NR.
Përkufizimi i funksionit
1
1 portë antene 5G, lidhës SMA, i cili mund të lidhet me antenën 5G.
2
1 x Micro SD card slot, functionally reserved only.
3
1 x Nano SIM card slot for installing a Nano SIM card to access 5G signals.
4
1 x portë antenash Wi-Fi/BT (opsionale), lidhës SMA, i cili mund të lidhet me antenën Wi-Fi/BT.
5
1 x Micro USB port, it supports to flash to eMMC for the system.
6
1 portë antene 5G, lidhës SMA, i cili mund të lidhet me antenën 5G.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
1.3.3 Paneli anësor
Ky seksion prezanton ndërfaqet dhe përkufizimet e panelit anësor.
ED-IPC2500
NR.
Përkufizimi i funksionit
1
1 x Butoni i rivendosjes, butoni i fshehur, shtypni butonin për të rinisur pajisjen.
2
2 x USB 2.0 ports, Type-A connector, each channel supports up to 480Mbps.
3
1 portë antene 5G, lidhës SMA, i cili mund të lidhet me antenën 5G.
1 x HDMI port, Type-A connector, which is compatibles with HDMI 2.0 standard and supports 4K 60Hz. It 4
mbështet lidhjen e një ekranuesi.
5
1 portë antene 5G, lidhës SMA, i cili mund të lidhet me antenën 5G.
1.4 Butoni
ED-IPC2500 device includes a RESET button, which is a hidden button, and the silkscreen on the case is “RESET”. Pressing the RESET button will reset the device.
1.5 Treguesi
Introducing the various statuses and meanings of indicators contained in ED-IPC2500 device.
Treguesi PWR
ACT USER
Status On Blink Off Blink
Joaktiv Aktivizohet
Description The device has been powered on. Power supply of the device is abnormal, please stop the power supply immediately. The device is not powered on. The system started successfully and is reading and writing data. The device is not powered on or does not read and write data. User can customize a status according to actual application.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
Treguesi
Statusi
5G Yellow indicator of Ethernet port Green indicator of Ethernet port
On Off On Blink Off On Blink Off
Description The device is not powered on or not defined by the user, and the default status is off. The dial-up is successful and the connection is normal. 5G signal is not connected or the device is not powered on. The data transmission is abnormal. Data is being transmitted over the Ethernet port. The Ethernet connection is not set up. The Ethernet connection is in the normal state. The Ethernet connection is abnormal. The Ethernet connection is not set up.
1.6 Ndërfaqja
Introducing the definition and function of each interface in ED-IPC2500 device.
1.6.1 Slot për karta SIM
The ED-IPC2500 device includes one Nano SIM card slot labeled with the silkscreen ” “, which is used for installing a SIM card to access 5G signals.
1.6.2 Ndërfaqja e fuqisë
The ED-IPC2500 device features one power input terminal, implemented as a 2-Pin 3.5mm-pitch phoenix connector. The interface is labeled with the silkscreen “VIN+/GND”, and the pin definitions are as follows.
ID e PIN-it 1 2
Emri i Pin-it GND 9V~36V
1.6.3 1000M Ethernet Interface (ETH0 ~ ETH2)
The ED-IPC2500 device includes three auto-sensing 10/100/1000M Ethernet interfaces, labeled
with the silkscreen ” “. These interfaces utilize RJ45 connectors, and for Ethernet connectivity, it is recommended to use Category 6 (Cat6) or higher-specification network cables. The pin definitions for the terminals are as follows:
PIN ID
Emri i pinit
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
1.6.4 Ndërfaqja HDMI
The ED-IPC2500 device features one HDMI interface with a silkscreen label “HDMI”, designed as a standard Type-A connector. It supports connection to HDMI displays and delivers video output up to 4K resolution at 60Hz (4K@60).
1.6.5 Ndërfaqja USB 2.0
The ED-IPC2500 device features two USB 2.0 interfaces, labeled with the silkscreen ” “. These utilize standard Type-A connectors, supporting connectivity with standard USB 2.0 peripherals and providing data transfer speeds up to 480 Mbps.
1.6.6 Ndërfaqe Mikro USB
The ED-IPC2500 device includes one Micro USB interface with a silkscreen label ” PROGRAMMING”. It supports flashing to eMMC when connected to a PC.
1.6.7 Wi-Fi Antenna Interface (optional)
The ED-IPC2500 device features one Wi-Fi antenna interface using an SMA connector, with a silkscreen label “WiFi/BT”, for connecting a dual-purpose Wi-Fi/Bluetooth antenna.
TIP If the selected device model is a non-Wi-Fi version, this interface will not be included.
1.6.8 5G Antenna Interface
The ED-IPC2500 device features four 5G antenna interfaces using SMA connectors, with silkscreen labels “5G”, for connecting 5G antennas.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
1.7 Supercapacitor (optional)
The ED-IPC2500 supports an optional supercapacitor backup power source, which provides the following functions:
· Power Failure Data Preservation: In the event of sudden power loss to the IPC device, the supercapacitor provides brief power support to critical circuitry within the IPC. Depending on the load, it can maintain operation for approximately one minute under lighter loads or about 30 seconds under heavier loads. This ensures that essential data (such as the device’s runtime state, current values of counters/timers, etc.) is preserved, preventing loss due to unexpected power interruption. This is critical for industrial applications requiring rapid process recovery without loss of key information.
· Real-Time Clock (RTC) Sustenance: The device’s RTC is crucial for recording event timestamps and sequencing operations. The supercapacitor supplies sufficient power to sustain the RTC circuit after primary power failure, allowing it to continue operating normally for a period.
· Assisting Graceful Shutdown: The supercapacitor supports an orderly shutdown procedure during power loss by supplying energy to the device’s control circuits. This enables the system to safely terminate active functions per predefined protocols–e.g., closing communication ports, halting complex calculations, or stopping runtime processes methodically.
KËSHILLA
The supercapacitor requires at least five minutes of charging while the device is powered on. Full functionality is guaranteed only after the supercapacitor is fully charged.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
2 Instalimi i Komponentëve
This chapter describes the specific operational procedures for installing antennas and SIM card.
2.1 Instalimi i antenave
The ED-IPC2500 device supports 5G and optional Wi-Fi functionality, with 5G requiring four antennas and Wi-Fi requiring one antenna. Antennas must be installed before operating the device. Preparation: Ensure the corresponding antennas have been retrieved from the packaging box. When multiple antennas are included, they should be identified by the labels on each antenna. Steps: 1. Locate the antenna interfaces on the device side as indicated in the diagram below.
TIP The antenna interfaces are located on both the rear panel and side panel of the device. This demonstration will exclusively use the rear panel as an example per shpjegim.
2. Align the corresponding interfaces on both the device and antenna, then tighten clockwise to ensure a secure connection.
2.2 Installing Nano SIM Card
The ED-IPC2500 device with 5G capability requires a SIM card to be installed first before utilizing the 5G functionality.
NOTE Hot-swapping of the SIM card is NOT supported.
Preparation: The 5G Nano SIM card to be used has been obtained.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
Steps: 1. Locate the position of the Nano SIM card slot on the device side as indicated in the diagram
më poshtë.
2. Insert the Nano SIM card with its golden contacts facing down into the corresponding slot. An audible click indicates successful installation.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
3 Nisja e pajisjes
Ky kapitull prezanton mënyrën e lidhjes së kabllove dhe të nisjes së pajisjes.
3.1 Kabllot lidhëse
Ky seksion përshkruan mënyrën e lidhjes së kabllove. Përgatitja:
· Verified operational peripherals have been obtained, including display, mouse, keyboard, and power adapter.
· A functional network connection has been established. · Operational HDMI and Ethernet cables have been secured. Schematic diagram of connecting cables: For specific pin definitions of each interface and wiring methods, refer to 1.6 Interface.
3.2 Nisja e sistemit për herë të parë
The ED-IPC2500 device does not feature a power switch. Upon connecting to a power source, the system will initiate startup.
· Solid red PWR LED: Indicates normal power supply to the device.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
· Blinking green ACT LED: Signals successful system initialization, followed by the Raspberry Pi logo appearing in the top-left corner of the display.
TIP · Default username: pi · Default password: raspberry
3.2.1 Raspberry Pi OS (Desktop)
If the Desktop edition of the system is preinstalled at the factory, the device will boot directly into the desktop environment upon completion of startup, as shown in the figure below.
3.2.2 Raspberry Pi OS (Lite)
If the Lite edition of the system is preinstalled at the factory, the device will automatically log in using the default username pi (password: raspberry ) upon startup completion. The interface shown below signifies a successful system boot.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
4 Konfigurimi i sistemit
Ky kapitull prezanton mënyrën e konfigurimit të sistemit.
4.1 Gjetja IP e pajisjes
Gjetja e IP-së së Pajisjes
4.2 Hyrja në distancë
Hyrja në distancë
4.3 Konfigurimi i pajisjeve të ruajtjes
Konfigurimi i pajisjeve të ruajtjes
4.4 Konfigurimi i IP-së së Ethernetit
Konfigurimi i IP-së Ethernet
4.5 Konfigurimi i Wi-Fi (Opsional)
Konfigurimi i Wi-Fi
4.6 Konfigurimi i Bluetooth (Opsional)
Konfigurimi i Bluetooth
4.7 Configuring 5G
The ED-IPC2500 natively supports 5G functionality, but specific configurations must be performed before utilizing the 5G network.
4.7.1 Scenarios Requiring No APN Configuration
If the user’s 5G network operates without APN configuration, connect by proceeding as follows: Preparation:
· The ED-IPC2500 device has completed normal startup. · A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.
SHËNIM
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
Hot-swapping of the SIM card is NOT supported.
ED-IPC2500
Hapat:
1. Open a terminal window and execute the following command to launch the 5G monitoring utility and automatically connect to the 5G network.
sh sudo ed-lte-tool –daemon
TIP After executing the command, the terminal window will display relevant log information.
3. Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).
sh ifconfig
The returned information is shown in the following figure:
· If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
· If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.
4.7.2 Scenarios Requiring APN Configuration
If the user’s 5G network requires APN configuration, configure the settings by proceeding as follows:
Përgatitja:
· The ED-IPC2500 device has completed normal startup. · A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
· APN credentials have been acquired, including the APN name, username, and password. The following example information will be used for demonstration: APN Name: APN1 Username: admin Password: admin
NOTE Hot-swapping of the SIM card is NOT supported.
Steps: 1. Open a terminal window and sequentially execute the following commands to access the ed-
qml.conf configuration file.
sh cd /etc/ sudo nano ed-qml.conf
2. Configure the “APN CONfig” settings as required by setting the “apn”, “apn_user”, and “apn_password” parameters.
TIP The “ping_server” and “online_script” parameters under the “Network” section also support user-specific configuration as required.
3. Enter ctrl+o to save the file, then press Enter to confirm, and finally input ctrl+x to exit file editing mode.
4. Execute the following command to launch the 5G monitoring utility and automatically establish the 5G network.
sh sudo ed-lte-tool –daemon
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
ED-IPC2500
TIP After executing the command, the terminal window will display relevant log information.
3. Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).
sh ifconfig
The returned information is shown in the following figure:
· If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
· If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.
4.7.3 Essential Configuration Commands
Command sudo systemctl start ed-lte-daemon.service sudo systemctl enable ed-lte-daemon.service sudo ed-lte-tool -r sudo ed-lte-tool -m sudo ed-lte-tool -s
sudo ed-lte -c
sudo ed-lte -d
cd /var/log/ed-qmi/ sudo nano xxxx-xx-xx.log
journalctl -u ed-lte-daemon.service
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
Description Establishing the 5G Network Connection via Service Automatically start the service during boot Resetting the 5G Module Viewing 5G Module Information Viewing 5G Signal Strength Dial-up networking does not support automatic reconnection after disconnection. Disconnect the network connection Navigate to the `/var/log/ed-qmi/` directory and review regjistrin files, where `xxxx-xx-xx` denotes the date in Year-Month-Day format (e.g., 2025-06-18). Monitor real-time logs for the 5G network
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
4.8 Konfigurimi i buzzer
Konfigurimi i ziles
4.9 Konfigurimi i RTC
Konfigurimi i RTC-së
4.10 Konfigurimi i Treguesit të PËRDORUESIT
Konfigurimi i Treguesit të PËRDORUESIT
ED-IPC2500
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telefoni: +86-15921483028 (Kinë) | +86-18217351262 (Jashtë shtetit)
Dokumentet / Burimet
 |
EDA TEC ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer [pdf] Manuali i Përdoruesit ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer, ED-IPC2500, 5G Raspberry Pi CM4 Industrial Computer, Pi CM4 Industrial Computer, Industrial Computer |