ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer
“
Impormasyon ng Produkto
Mga pagtutukoy
The ED-IPC2500 is a 5G industrial computer based on the
Raspberry Pi CM4. It offers different RAM and eMMC specifications
based on user requirements. The device includes interfaces such as
HDMI, USB 2.0, and Ethernet, supporting network access via Wi-Fi,
Ethernet, and 5G. Additional features include a supercapacitor
backup power supply (optional), RTC, Watch Dog, EEPROM, and
encryption chip for enhanced usability and reliability. Primarily
used in industrial control and IoT fields.
Mga Tagubilin sa Paggamit ng Produkto
1. Tapos na ang Hardwareview
The ED-IPC2500 is equipped with various interfaces for
connectivity, including HDMI, USB 2.0, and Ethernet. It also
supports network access via Wi-Fi, Ethernet, and 5G.
2. Front Panel
The front panel features indicators for power status, 5G signal
status, system status, and user-defined status. It also includes a
DC input for power supply.
3. Rear Panel
The rear panel includes ports for 5G antenna connection, Micro
SD card slot (reserved function), Nano SIM card slot for 5G access,
Wi-Fi/BT antenna port (optional), Micro USB port for flashing to
eMMC, and additional 5G antenna port.
4. Side Panel
The side panel consists of a reset button for device restart,
USB 2.0 ports for peripheral connections, HDMI port for display
connectivity, and multiple 5G antenna ports.
The device includes a hidden reset button that can be pressed to
i-restart ang device.
6. Tagapagpahiwatig
The device features indicators for power status, 5G signal
status, system status, and user-defined status.
Mga Madalas Itanong (FAQ)
Q: What are the main applications of the ED-IPC2500?
A: The ED-IPC2500 is mainly used in industrial control and
Internet of Things (IoT) fields due to its reliability and ease of
gamitin.
Q: Paano ko mai-reset ang device?
A: Press the hidden reset button located on the side panel to
i-restart ang device.
“`
ED-IPC2500
User Manual
ng EDA Technology Co., Ltd na binuo: 2025-08-01
ED-IPC2500
1 Manual ng Hardware
Ang kabanatang ito ay nagpapakilala sa produktoview, listahan ng packing, hitsura, button, indicator at interface.
1.1 Lampasview
The ED-IPC2500 is a 5G industrial computer based on the Raspberry Pi CM4. Depending on the application scenario and user requirements, computer systems with different RAM and eMMC specifications can be selected.
· RAM options include 1GB, 2GB, 4GB, and 8GB. · eMMC options include 8GB, 16GB, and 32GB.
The ED-IPC2500 provides commonly used interfaces such as HDMI, USB 2.0, and Ethernet. It supports network access via Wi-Fi, Ethernet, and 5G. The integration of a supercapacitor backup power supply (optional), RTC (Real-Time Clock), Watch Dog, EEPROM, and an encryption chip enhances the product’s ease of use and reliability. It is mainly used in industrial control and Internet of Things (IoT) fields.
1.2 Listahan ng Pag-iimpake
· 1 x ED-IPC2500 Unit · [WiFi/BT Version – optional] 1 x 2.4GHz/5GHz Wi-Fi/BT Antenna
1.3 Hitsura
Ipinapakilala ang mga function at kahulugan ng mga interface sa bawat panel.
1.3.1 Front Panel
Ipinakikilala ng seksyong ito ang mga function at kahulugan ng front panel.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
HINDI.
Kahulugan ng Function
1
1 x pulang power indicator, na ginagamit para tingnan ang status ng power-on at power-off ng device.
2
1 x berdeng 5G indicator, na ginagamit para tingnan ang status ng 5G signal.
1 x DC input, 2-Pin 3.5mm spacing phoenix terminals with screw holes. It supports 9V~36V input, the signal 3
is defined as VIN+/GND.
3 × 1000M Ethernet interfaces (ETH0ETH2), RJ45 connector with LED indicators, 10/100/1000M auto4
sensing interfaces for Ethernet connection.
5
1 x green system status indicator, na ginagamit upang suriin ang working status ng device.
6
1 x berdeng tagapagpahiwatig ng gumagamit, maaaring i-customize ng user ang isang katayuan ayon sa aktwal na aplikasyon.
1.3.2 Rear Panel
Ipinakikilala ng seksyong ito ang mga interface at mga kahulugan ng rear panel.
HINDI.
Kahulugan ng Function
1
1 x 5G antenna port, SMA connector, na maaaring kumonekta sa 5G antenna.
2
1 x Micro SD card slot, functionally reserved only.
3
1 x Nano SIM card slot for installing a Nano SIM card to access 5G signals.
4
1 x Wi-Fi/BT antenna port (opsyonal), SMA connector, na maaaring kumonekta sa Wi-Fi/BT antenna.
5
1 x Micro USB port, it supports to flash to eMMC for the system.
6
1 x 5G antenna port, SMA connector, na maaaring kumonekta sa 5G antenna.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
1.3.3 Panel sa Gilid
Ang seksyong ito ay nagpapakilala ng mga interface at mga kahulugan ng side panel.
ED-IPC2500
HINDI.
Kahulugan ng Function
1
1 x I-reset ang button, hidden button, pindutin ang button para i-restart ang device.
2
2 x USB 2.0 ports, Type-A connector, each channel supports up to 480Mbps.
3
1 x 5G antenna port, SMA connector, na maaaring kumonekta sa 5G antenna.
1 x HDMI port, Type-A connector, which is compatibles with HDMI 2.0 standard and supports 4K 60Hz. It 4
sumusuporta sa pagkonekta ng isang displayer.
5
1 x 5G antenna port, SMA connector, na maaaring kumonekta sa 5G antenna.
1.4 Pindutan
ED-IPC2500 device includes a RESET button, which is a hidden button, and the silkscreen on the case is “RESET”. Pressing the RESET button will reset the device.
1.5 Tagapagpahiwatig
Introducing the various statuses and meanings of indicators contained in ED-IPC2500 device.
Tagapagpahiwatig ng PWR
ACT USER
Status Sa Blink Off Blink
Patay Na
Description The device has been powered on. Power supply of the device is abnormal, please stop the power supply immediately. The device is not powered on. The system started successfully and is reading and writing data. The device is not powered on or does not read and write data. User can customize a status according to actual application.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
Tagapagpahiwatig
Katayuan
5G Yellow indicator of Ethernet port Green indicator of Ethernet port
On Off On Blink Off On Blink Off
Description The device is not powered on or not defined by the user, and the default status is off. The dial-up is successful and the connection is normal. 5G signal is not connected or the device is not powered on. The data transmission is abnormal. Data is being transmitted over the Ethernet port. The Ethernet connection is not set up. The Ethernet connection is in the normal state. The Ethernet connection is abnormal. The Ethernet connection is not set up.
1.6 Interface
Introducing the definition and function of each interface in ED-IPC2500 device.
1.6.1 Slot ng SIM Card
The ED-IPC2500 device includes one Nano SIM card slot labeled with the silkscreen ” “, which is used for installing a SIM card to access 5G signals.
1.6.2 Power Interface
The ED-IPC2500 device features one power input terminal, implemented as a 2-Pin 3.5mm-pitch phoenix connector. The interface is labeled with the silkscreen “VIN+/GND”, and the pin definitions are as follows.
Pin ID 1 2
Pangalan ng Pin GND 9V~36V
1.6.3 1000M Ethernet Interface (ETH0 ~ ETH2)
The ED-IPC2500 device includes three auto-sensing 10/100/1000M Ethernet interfaces, labeled
with the silkscreen ” “. These interfaces utilize RJ45 connectors, and for Ethernet connectivity, it is recommended to use Category 6 (Cat6) or higher-specification network cables. The pin definitions for the terminals are as follows:
Pin ID
Pangalan ng Pin
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
1.6.4 HDMI Interface
The ED-IPC2500 device features one HDMI interface with a silkscreen label “HDMI”, designed as a standard Type-A connector. It supports connection to HDMI displays and delivers video output up to 4K resolution at 60Hz (4K@60).
1.6.5 USB 2.0 Interface
The ED-IPC2500 device features two USB 2.0 interfaces, labeled with the silkscreen ” “. These utilize standard Type-A connectors, supporting connectivity with standard USB 2.0 peripherals and providing data transfer speeds up to 480 Mbps.
1.6.6 Micro USB Interface
The ED-IPC2500 device includes one Micro USB interface with a silkscreen label ” PROGRAMMING”. It supports flashing to eMMC when connected to a PC.
1.6.7 Wi-Fi Antenna Interface (optional)
The ED-IPC2500 device features one Wi-Fi antenna interface using an SMA connector, with a silkscreen label “WiFi/BT”, for connecting a dual-purpose Wi-Fi/Bluetooth antenna.
TIP If the selected device model is a non-Wi-Fi version, this interface will not be included.
1.6.8 5G Antenna Interface
The ED-IPC2500 device features four 5G antenna interfaces using SMA connectors, with silkscreen labels “5G”, for connecting 5G antennas.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
1.7 Supercapacitor (optional)
The ED-IPC2500 supports an optional supercapacitor backup power source, which provides the following functions:
· Power Failure Data Preservation: In the event of sudden power loss to the IPC device, the supercapacitor provides brief power support to critical circuitry within the IPC. Depending on the load, it can maintain operation for approximately one minute under lighter loads or about 30 seconds under heavier loads. This ensures that essential data (such as the device’s runtime state, current values of counters/timers, etc.) is preserved, preventing loss due to unexpected power interruption. This is critical for industrial applications requiring rapid process recovery without loss of key information.
· Real-Time Clock (RTC) Sustenance: The device’s RTC is crucial for recording event timestamps and sequencing operations. The supercapacitor supplies sufficient power to sustain the RTC circuit after primary power failure, allowing it to continue operating normally for a period.
· Assisting Graceful Shutdown: The supercapacitor supports an orderly shutdown procedure during power loss by supplying energy to the device’s control circuits. This enables the system to safely terminate active functions per predefined protocols–e.g., closing communication ports, halting complex calculations, or stopping runtime processes methodically.
TIP
The supercapacitor requires at least five minutes of charging while the device is powered on. Full functionality is guaranteed only after the supercapacitor is fully charged.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
2 Mga Pag-install ng Mga Sangkap
This chapter describes the specific operational procedures for installing antennas and SIM card.
2.1 Pag-install ng mga Antenna
The ED-IPC2500 device supports 5G and optional Wi-Fi functionality, with 5G requiring four antennas and Wi-Fi requiring one antenna. Antennas must be installed before operating the device. Preparation: Ensure the corresponding antennas have been retrieved from the packaging box. When multiple antennas are included, they should be identified by the labels on each antenna. Steps: 1. Locate the antenna interfaces on the device side as indicated in the diagram below.
TIP The antenna interfaces are located on both the rear panel and side panel of the device. This demonstration will exclusively use the rear panel as an example para sa paliwanag.
2. Align the corresponding interfaces on both the device and antenna, then tighten clockwise to ensure a secure connection.
2.2 Installing Nano SIM Card
The ED-IPC2500 device with 5G capability requires a SIM card to be installed first before utilizing the 5G functionality.
NOTE Hot-swapping of the SIM card is NOT supported.
Preparation: The 5G Nano SIM card to be used has been obtained.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
Steps: 1. Locate the position of the Nano SIM card slot on the device side as indicated in the diagram
sa ibaba.
2. Insert the Nano SIM card with its golden contacts facing down into the corresponding slot. An audible click indicates successful installation.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
3 Pag-boot ng Device
Ipinapakilala ng kabanatang ito kung paano ikonekta ang mga cable at i-boot ang device.
3.1 Pagkonekta ng mga Kable
Inilalarawan ng seksyong ito kung paano ikonekta ang mga cable. Paghahanda:
· Verified operational peripherals have been obtained, including display, mouse, keyboard, and power adapter.
· A functional network connection has been established. · Operational HDMI and Ethernet cables have been secured. Schematic diagram of connecting cables: For specific pin definitions of each interface and wiring methods, refer to 1.6 Interface.
3.2 Pag-boot ng System Sa Unang pagkakataon
The ED-IPC2500 device does not feature a power switch. Upon connecting to a power source, the system will initiate startup.
· Solid red PWR LED: Indicates normal power supply to the device.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
· Blinking green ACT LED: Signals successful system initialization, followed by the Raspberry Pi logo appearing in the top-left corner of the display.
TIP · Default username: pi · Default password: raspberry
3.2.1 Raspberry Pi OS (Desktop)
If the Desktop edition of the system is preinstalled at the factory, the device will boot directly into the desktop environment upon completion of startup, as shown in the figure below.
3.2.2 Raspberry Pi OS (Lite)
If the Lite edition of the system is preinstalled at the factory, the device will automatically log in using the default username pi (password: raspberry ) upon startup completion. The interface shown below signifies a successful system boot.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
4 Pag-configure ng System
Ipinapakilala ng kabanatang ito kung paano i-configure ang system.
4.1 Paghahanap ng IP ng Device
Paghahanap ng IP ng Device
4.2 Malayong Pag-login
Remote na Pag-login
4.3 Pag-configure ng Mga Storage Device
Pag-configure ng Mga Storage Device
4.4 Pag-configure ng Ethernet IP
Pag-configure ng Ethernet IP
4.5 Pag-configure ng Wi-Fi (Opsyonal)
Pag-configure ng Wi-Fi
4.6 Pag-configure ng Bluetooth (Opsyonal)
Pag-configure ng Bluetooth
4.7 Configuring 5G
The ED-IPC2500 natively supports 5G functionality, but specific configurations must be performed before utilizing the 5G network.
4.7.1 Scenarios Requiring No APN Configuration
If the user’s 5G network operates without APN configuration, connect by proceeding as follows: Preparation:
· The ED-IPC2500 device has completed normal startup. · A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.
TANDAAN
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
Hot-swapping of the SIM card is NOT supported.
ED-IPC2500
Mga hakbang:
1. Open a terminal window and execute the following command to launch the 5G monitoring utility and automatically connect to the 5G network.
sh sudo ed-lte-tool –daemon
TIP After executing the command, the terminal window will display relevant log information.
3. Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).
sh ifconfig
The returned information is shown in the following figure:
· If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
· If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.
4.7.2 Scenarios Requiring APN Configuration
If the user’s 5G network requires APN configuration, configure the settings by proceeding as follows:
Paghahanda:
· The ED-IPC2500 device has completed normal startup. · A 5G-enabled Nano SIM card has been correctly installed in the device’s SIM card slot.
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
· APN credentials have been acquired, including the APN name, username, and password. The following example information will be used for demonstration: APN Name: APN1 Username: admin Password: admin
NOTE Hot-swapping of the SIM card is NOT supported.
Steps: 1. Open a terminal window and sequentially execute the following commands to access the ed-
qml.conf configuration file.
sh cd /etc/ sudo nano ed-qml.conf
2. Configure the “APN CONfig” settings as required by setting the “apn”, “apn_user”, and “apn_password” parameters.
TIP The “ping_server” and “online_script” parameters under the “Network” section also support user-specific configuration as required.
3. Enter ctrl+o to save the file, then press Enter to confirm, and finally input ctrl+x to exit file editing mode.
4. Execute the following command to launch the 5G monitoring utility and automatically establish the 5G network.
sh sudo ed-lte-tool –daemon
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
ED-IPC2500
TIP After executing the command, the terminal window will display relevant log information.
3. Open a new terminal window and execute the following command to check the status of the 5G interface (wwan interface).
sh ifconfig
The returned information is shown in the following figure:
· If the returned information includes the wwan0 interface and displays an assigned IP address, this indicates that the 5G network is connected.
· If the returned information shows no wwan0 interface, this signifies that the 5G network is disconnected.
4.7.3 Essential Configuration Commands
Command sudo systemctl start ed-lte-daemon.service sudo systemctl enable ed-lte-daemon.service sudo ed-lte-tool -r sudo ed-lte-tool -m sudo ed-lte-tool -s
sudo ed-lte -c
sudo ed-lte -d
cd /var/log/ed-qmi/ sudo nano xxxx-xx-xx.log
journalctl -u ed-lte-daemon.service
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
Description Establishing the 5G Network Connection via Service Automatically start the service during boot Resetting the 5G Module Viewing 5G Module Information Viewing 5G Signal Strength Dial-up networking does not support automatic reconnection after disconnection. Disconnect the network connection Navigate to the `/var/log/ed-qmi/` directory and review ang log files, where `xxxx-xx-xx` denotes the date in Year-Month-Day format (e.g., 2025-06-18). Monitor real-time logs for the 5G network
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
4.8 Pag-configure ng Buzzer
Pag-configure ng Buzzer
4.9 Pag-configure ng RTC
Kino-configure ang RTC
4.10 Pag-configure ng USER Indicator
Pag-configure ng USER Indicator
ED-IPC2500
Email: sales@edatec.cn / support@edatec.cn Web: www.edatec.cn
|
Telepono: +86-15921483028(China) | +86-18217351262(Overseas)
Mga Dokumento / Mga Mapagkukunan
 |
EDA TEC ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer [pdf] User Manual ED-IPC2500 5G Raspberry Pi CM4 Industrial Computer, ED-IPC2500, 5G Raspberry Pi CM4 Industrial Computer, Pi CM4 Industrial Computer, Industrial Computer |