UNI-T UTG1000 Series Function Arbitrary Waveform Jenareta Mushandisi Manual

Vanodiwa Vashandisi:
Mhoro! Ndatenda nekusarudza iyi brand new Uni-Trend mudziyo. Kuti ushandise chiridzwa ichi zvakachengeteka uye nemazvo, ndapota verenga bhuku rino zvakanyatsonaka, kunyanya chikamu Chekuchengetedza Notes.
Mushure mekuverenga bhuku rino, zvinokurudzirwa kuchengeta bhuku racho panzvimbo inosvika nyore nyore, zvichida pedyo nemudziyo, kuitira ramangwana.

Copyright Information

UNl-T is Uni-Trend Technology (China) Limited. Kodzero dzese dzakachengetwa.
Zvigadzirwa zveUNI-T zvinodzivirirwa nekodzero dzepatent muChina nedzimwe nyika, kusanganisira dzakapihwa uye dzakamirira patent.
Uni-Trend inochengetedza kodzero kune chero chigadzirwa chinotsanangurwa uye kuchinja kwemitengo.
Uni-Trend inochengetedza kodzero dzese. Zvigadzirwa zvesoftware zvine rezenisi zvivakwa zveUni-Trend uye vatsigiri vayo kana vatengesi, izvo zvinodzivirirwa nemitemo yenyika yekodzero uye zvibvumirano zvepasi rose. Mashoko ari muchinyorwa chino anodarika shanduro dzose dzakambodhindwa.
UNI-T ndicho chiziviso chakanyoreswa cheUni-Trend Technology (China) Limited.
Uni-Trend inobvumidza kuti chigadzirwa ichi chive chisina hurema kwenguva yemakore matatu. Kana chigadzirwa chikatengeswa zvakare, nguva yewaranti ichave kubva pazuva rekutenga kwekutanga kubva kune ane mvumo UNI-T distributor. Probes, zvimwe zvishongedzo, uye fuse hazvina kubatanidzwa mune iyi waranti.
Kana chigadzirwa chikaonekwa kuti hachina kumira zvakanaka mukati menguva yewaranti, Uni-Trend inochengetera kodzero yekugadzirisa chigadzirwa chisina kubhadhariswa chero chikamu kana vashandi, kana kuchinjana chigadzirwa kune chimwe chinoshanda chakaenzana. Zvikamu zvinotsiviwa uye zvigadzirwa zvinogona kunge zviri zvitsva, kana kuita zvakafanana nemhando yezvigadzirwa zvitsva. Zvese zvinotsiva zvikamu, mamodule, uye zvigadzirwa zvinhu zveUni-Trend.
Izwi rokuti "mutengi" rinoreva munhu kana sangano rinoziviswa muvimbiso. Kuti uwane sevhisi yewaranti, “mutengi” anofanira kuzivisa zvakakanganisika mukati menguva yewaranti iripo kuUNI-T, uye kuita gadziriro dzakakodzera dzesevhisi yewaranti. Mutengi achava nebasa rekurongedza nekutumira zvinhu zvisina kurongeka kunzvimbo yakatarwa yeUNI-T, kubhadhara mutengo wekutumira, uye nekupa kopi yerisiti yekutenga yemutengi wekutanga. Kana chigadzirwa chacho chikatumirwa kumusha kunzvimbo yeUNI-T service centre, UNI-T ichabhadhara mari yekudzorera yekutumira. Kana chigadzirwa chikatumirwa kune imwe nzvimbo, mutengi ndiye achave nemutoro wekutumira zvese, mabasa, mutero, uye chero mari ipi zvayo.
Iyi waranti haishande kune chero hurema kana kukuvadzwa kunokonzerwa netsaona, zvidimbu zvemuchina kusakara uye kubvaruka, kushandiswa zvisina kunaka, uye kushaikwa kwekugadzirisa. UNI-T pasi pezvisungo zvewaranti iyi haina chisungo chekupa masevhisi anotevera:
a) Chero kukuvara kwekugadzirisa kunokonzerwa nekuiswa, kugadzirisa, kana kugadzirisa kwechigadzirwa nevasiri veUNI-T vamiriri vebasa.
b) Chero kukanganisa kwekugadzirisa kunokonzerwa nekushandisa zvisina kunaka kana kubatana kune isingaenderane mudziyo.
c) Chero kukanganisa kana kusashanda kunokonzerwa nekushandiswa kwesimba remagetsi risingaenderane nezvinodiwa nebhuku rino.
d) Chero kuchengetedza pane zvakashandurwa kana zvakabatanidzwa zvigadzirwa (kana shanduko yakadaro kana kubatanidzwa kunotungamira mukuwedzera kwenguva kana kuoma kwekugadzirisa chigadzirwa).
Iyi waranti yakanyorwa neUNI-T yechigadzirwa ichi, uye inoshandiswa kutsiva chero yakaratidzwa kana kurehwa waranti. UNI-T nevashambadziri vayo havape chero yairehwa waranti yekutengesa kana kushanda kwezvinangwa.
Nekutyorwa kwechivimbiso ichi, UNI-T ine basa rekugadzirisa kana kutsiviwa kwezvakaremara zvigadzirwa ndiyo yega mushonga unowanikwa kune vatengi. Zvisinei nekuti UNI-T nevashambadziri vayo vachaziviswa kuti chero kukuvara kusina kunanga, kwakakosha, kwezvine njodzi, kana kunokonzeresa kungaitika, UNI-T nevanozvigovera havazovi nemhosva yekukuvadza kupi zvako.

Warranty

UNI-T inobvumidza kuti chigadzirwa chive chisina kuremara kwenguva yemakore matatu. Kana chigadzirwa chikatengeswa zvakare, nguva yewaranti ichave kubva pazuva rekutenga kwekutanga kubva kune ane mvumo UNI-T distributor. Probes, zvimwe zvishongedzo, uye fuse hazvina kubatanidzwa mune iyi waranti.
Kana chigadzirwa chikaonekwa kuti hachina kukwana mukati menguva yewarranty, UNI-T inochengetera kodzero yekugadzirisa chigadzirwa chakakanganisika pasina kubhadharisa zvikamu nevashandi, kana kuchinjanisa chigadzirwa chakakanganisika kune chimwe chinoshanda chakaenzana. Zvikamu zvinotsiviwa uye zvigadzirwa zvinogona kunge zviri zvitsva, kana kuita zvakafanana nemhando yezvigadzirwa zvitsva. Zvese zvinotsiva zvikamu, mamodule, uye zvigadzirwa zvinova pfuma yeUNI-T.
“Mutengi” zvinoreva munhu kana sangano rinoziviswa mugarandi. Kuti uwane sevhisi yewaranti, “mutengi” anofanira kuzivisa zvakakanganisika mukati menguva yewaranti iripo kuUNI-T, uye kuita gadziriro dzakakodzera dzesevhisi yewaranti. Mutengi achava nebasa rekurongedza nekutumira zvinhu zvisina kurongeka kunzvimbo yakatarwa yeUNI-T, kubhadhara mutengo wekutumira, uye nekupa kopi yerisiti yekutenga yemutengi wekutanga. Kana chigadzirwa chacho chikatumirwa kumusha kunzvimbo yeUNI-T service centre, UNI-T ichabhadhara mari yekudzorera yekutumira. Kana chigadzirwa chikatumirwa kune imwe nzvimbo, mutengi ndiye achave nemutoro wekutumira zvese, mabasa, mutero, uye chero mari ipi zvayo.
Waranti iyi haishande kune chero hurema kana kukuvadzwa kunokonzerwa netsaona, machira emuchina kubvaruka uye kubvaruka, kushandisa zvisina kunaka, uye kushaikwa kwekugadzirisa. UNI-T pasi pezvisungo zvewaranti iyi haina chisungo chekupa masevhisi anotevera:
a) Chero kukuvara kwekugadzirisa kunokonzerwa nekuiswa, kugadzirisa, kana kugadzirisa kwechigadzirwa nevasiri veUNI-T vamiriri vebasa.
b) Chero kukanganisa kwekugadzirisa kunokonzerwa nekushandisa zvisina kunaka kana kubatana kune isingaenderane mudziyo.
c) Chero kukanganisa kana kusashanda kunokonzerwa nekushandiswa kwesimba remagetsi risingaenderane nezvinodiwa nebhuku rino.
d) Chero kuchengetedza pane zvakashandurwa kana zvakabatanidzwa zvigadzirwa (kana shanduko yakadaro kana kubatanidzwa kunotungamira mukuwedzera kwenguva kana kuoma kwekugadzirisa chigadzirwa).
Iyi waranti yakanyorwa neUNI-T yechigadzirwa ichi, uye inoshandiswa kutsiva chero imwe nzira yekutaura kana yekuremerwa waranti.
UNI-T nevashambadziri vayo havape chero yairehwa waranti yekutengesa kana kushandiswa kwezvinangwa.
Nekutyorwa kwechivimbiso ichi, UNI-T ine basa rekugadzirisa kana kutsiviwa kwezvakaremara zvigadzirwa ndiyo yega mushonga unowanikwa kune vatengi. Zvisinei nekuti UNI-T nevashambadziri vayo vachaziviswa kuti chero kukuvara kusina kunanga, kwakakosha, kwezvine njodzi, kana kunokonzeresa kungaitika, UNI-T nevanozvigovera havazovi nemhosva yekukuvadza kupi zvako.

General Safety Overview

Ichi chiridzwa chinonyatsoenderana nezvinodiwa zvekuchengetedza zvemagetsi kuyera chiridzwa GB4793 uye IEC 61010-1 chiyero chekuchengetedza panguva yekugadzira nekugadzira. Ndokumbira unzwisise matanho anotevera ekudzivirira, kudzivirira kukuvara kwako, uye kudzivirira kukuvara kuchigadzirwa kana chero zvigadzirwa zvakabatana.
Kuti udzivise njodzi dzinogona kuitika, iva nechokwadi chekushandisa chigadzirwa ichi maererano nemirairo.
Vashandi vakadzidziswa chete ndivo vanogona kuita chirongwa chekugadzirisa.
Dzivisa moto uye kukuvara pachako.
Shandisa iyo chaiyo tambo yemagetsi: Ingo shandisa yakatsaurirwa UNI-T magetsi akagadzwa kudunhu renzvimbo kana nyika yechigadzirwa ichi.
Yakarurama Plug: Usa plug kana probe kana waya yekuyedza yabatana nevoltage source.
Ground chigadzirwa: Ichi chigadzirwa chinodzikwa kuburikidza nemagetsi epasi waya. Kuti udzivise kuvhunduka kwemagetsi, maconductors ekudzika anofanira kubatanidzwa pasi. Ndapota iva nechokwadi chekuti chigadzirwa chakanyatsodzika pasi usati wabatana nekuisa kana kubuda kwechigadzirwa.
Kubatana chaiko kweoscilloscope probe: Iva nechokwadi chekuti probe pasi uye mukana wepasi zvakabatana nemazvo. Usabatanidza waya yepasi kune yakakwirira voltage.
Tarisa ese materminal ratings: Kuti udzivise moto uye hombe yazvino kuchaja, ndapota tarisa ese mareti uye mamaki pachigadzirwa. Ndokumbirawo utarise kune chigadzirwa bhuku kuti uwane ruzivo rwezviyero usati wabatana nechigadzirwa.
Usavhure chivharo chekesi kana pani yekumberi panguva yekushanda
Shandisa ma fuse ane zviyero zvakarongwa mutechnical index
Dzivisa kuratidzwa kwedunhu: Usabate zvakafumurwa zvibatanidza uye zvikamu mushure mekunge simba rabatanidzwa.
Usashandise chigadzirwa kana uchifungidzira kuti chakashata, uye ndapota taura neUNI-T ine mvumo yevashandi vebasa kuti vaongororwe. Chero kugadzirisa, kugadzirisa, kana kutsiviwa kwezvikamu kunofanirwa kuitwa nevashandi vane mvumo yeUNI-T.
Chengetedza mhepo yakakwana
Ndapota usashandise chigadzirwa mumamiriro ekunyorova
Ndapota usashande munzvimbo inopisa uye inoputika
Ndapota chengetedza chigadzirwa chepamusoro chakachena uye chakaoma

Mitemo Yekuchengetedza uye Zviratidzo

Aya mazwi anotevera anogona kuoneka mubhuku rino.
Yambiro: Mamiriro ezvinhu uye maitiro anogona kuisa hupenyu munjodzi.
Ongorora: Mamiriro uye maitiro anogona kukonzera kukanganisa kuchigadzirwa uye zvimwe zvivakwa.
Matemu anotevera anogona kuoneka pachigadzirwa:
Ngozi:Kuita oparesheni iyi kunogona kukonzera kukuvara nekukurumidza kumushandisi.
Yambiro:Kushanda uku kunogona kukonzera kukanganisa kune mushandisi.
Ongorora:Kushanda uku kunogona kukonzera kukanganisa kuchigadzirwa uye zvishandiso zvakabatana nechigadzirwa.
Zviratidzo zvinotevera zvinogona kuoneka pane chigadzirwa:

Chitsauko 1– Nhungamidzo Yekutungamira

1.1 Mitemo Yekuchengetedza uye Zviratidzo
Aya mazwi anotevera anogona kuoneka mubhuku rino.
Yambiro: Mamiriro ezvinhu uye maitiro anogona kuisa hupenyu munjodzi.
Ongorora: Mamiriro uye maitiro anogona kukonzera kukanganisa kuchigadzirwa uye zvimwe zvivakwa.
Matemu anotevera anogona kuoneka pachigadzirwa:
Ngozi: Kuita oparesheni iyi kunogona kukonzera kukuvara nekukurumidza kumushandisi.
Yambiro: Kuvhiya uku kunogona kukonzera kukanganisa kune mushandisi.
Ongorora: Kuvhiya uku kunogona kukonzera kukanganisa kuchigadzirwa nemidziyo yakabatana nechigadzirwa.
Zviratidzo pane chigadzirwa.
Zviratidzo zvinotevera zvinogona kuoneka pane chigadzirwa:

	Alternating Current
	Ground Terminal for Testing
	Ground Terminal yeChassis
	Batanidza/Kudzima
	Yakakwira Voltage
	Chenjero! Tarisa kuna Manual
	Dziviriro Ground Terminal
	CE logo chiratidzo chakanyoreswa cheEuropean Union.
N0149	C-tick logo chiratidzo chekutengeserana chakanyoreswa chekuAustralia.
(40)	Environmental Protection Use Period (EPUP)

1.2 General Chengetedzo Yaperaview
Ichi chiridzwa chinonyatsoenderana neiyo GB4793 kuchengetedza zvinodiwa pamidziyo yemagetsi uye EN61010-1/2 chiyero chekuchengetedza panguva yekugadzira nekugadzira. Zvinoenderana nedziviriro zviyero zve insulated voltage standard CAT II 300V uye kusvibiswa level II.
Ndokumbira uverenge matanho ekudzivirira anotevera:
Kuti udzivise kuvhunduka kwemagetsi nemoto, ndapota shandisa yakatsaurirwa UNI-T magetsi akagadzwa kudunhu renzvimbo kana nyika yechigadzirwa ichi.
Ichi chigadzirwa chinodzikwa kuburikidza nemagetsi epasi waya. Kuti udzivise kuvhunduka kwemagetsi, maconductors ekudzika anofanira kubatanidzwa pasi. Ndokumbira uve nechokwadi chekuti chigadzirwa chakadzikwa zvakanaka usati wabatana nekuisa kana kubuda kwechigadzirwa.
Kuti udzivise kukuvara kwemunhu uye kudzivirira kukuvadza chigadzirwa, vashandi vakadzidziswa chete vanogona kuita chirongwa chekuchengetedza.
Kuti udzivise moto kana kuvhunduka kwemagetsi, ndapota cherechedza yakayerwa mashandisirwo emhando uye mamaki echigadzirwa. Usashandise chigadzirwa kunze kweiyo yakatarwa renji.
Ndokumbira utarise zvishongedzo kune chero kukuvara kwemagetsi usati washandisa.
Shandisa zvishongedzo zvakauya nechigadzirwa ichi chete.
Ndapota usaise zvinhu zvesimbi mune zvekupinza uye zvinobuda zviteshi zvechigadzirwa ichi.
Usashandise chigadzirwa kana uchifungidzira kuti chakashata, uye ndapota taura neUNI-T ine mvumo yevashandi vebasa kuti vaongororwe.
Ndapota usashandise chigadzirwa kana bhokisi rezviridzwa richivhura.
Ndapota usashandise chigadzirwa mumamiriro ekunyorova.
Ndapota chengetedza chigadzirwa chepamusoro chakachena uye chakaoma.
Kana iyo midziyo ikashandiswa nenzira isina kutaurwa nemugadziri, kudzivirira kunopiwa nemidziyo kunogona kukanganisa.

Chitsauko 2 Nhanganyaya

Ichi chishandiso chine hupfumi, chepamusoro-chinoita, chakawanda-chinoshanda single chiteshi waveform jenareta. Inoshandisa yakananga dhijitari synthesis (DDS) tekinoroji kuburitsa echokwadi uye akagadzikana masaisai, ine resolution yakaderera se1μHz. Inogona kuburitsa masaini echokwadi, akatsiga, akachena uye akaderera anoburitsa masiginecha, zvakare anogona kupa yakakwirira-frequency vertical edge square waves. UTG1000's interface iri nyore, yepamusoro tekinoroji indexes uye mushandisi-ane hushamwari graphical kuratidza maitiro anogona kubatsira vashandisi kupedza mabasa nekukurumidza uye kunatsiridza kushanda zvakanaka.

2.1 Hunhu Hukuru

Sine wave kubuda kwe20MHz/10MHz/5MHz, yakazara frequency range resolution ndeye 1μHz
Square wave/pulse waveform ye5MHz, uye kusimuka kwayo, kudonha, uye basa rekutenderera nguva zvinogadziriswa.

Kushandisa DDS kuita nzira, ine 125M/s sampling rate uye 14bits vertical resolution
6-bit high precision frequency counter iyo iri TTL level inoenderana

Arbitrary waveform chengetedzo ye2048 mapoinzi, uye inogona kuchengeta anosvika 16 mapoka easina kuvhurika edhijitari arbitrary waveforms.
Yakawanda modulation mhando: AM, FM, PM, Bvunza, FSK, PSK, PWM

Yakasimba PC software
4.3-inch high resolution TFT liquid crystal display

Yakajairwa gadziriso interface: USB Chishandiso
Inotsigira mukati / kunze modulation uye mukati / kunze / manual trigger

Inotsigira kutsvaira kubuda
Easy-kushandisa-multifunctional knob uye nhamba keyboard

2.2 Panel uye mabhatani
2.2.1 Pamberi Panel
UTG1000A nhevedzano inopa vashandisi nyore, intuitive, uye nyore kushandisa kumberi kwepaneru. Iyo yepamberi pani inoratidzwa mumufananidzo 2-1:

Ratidza Sikirini
4.3-inch TFT LCD inoratidza yakakwirira-resolution yekubuda mamiriro, basa menyu, uye mamwe akakosha chiteshi ruzivo. Yakagadzirirwa kuita kuti kusangana kwevanhu-kombuta kuve nyore kuvandudza kushanda zvakanaka.

Batanidza/Kudzima
Kuti ubatidze / kudzima mudziyo, dzvanya bhatani iri uye backlight yayo ichabatidza (orenji), iyo inoratidzira icharatidza basa rekuita mushure mebhoti skrini.
Menyu Operation Softkeys
Sangana sarudza kana tarisa zviri mukati maro nekuzivikanwa kwemavara manyoro (pazasi pebasa rekushanda).

Inobatsira Basa uye Sistimu Settings Bhatani
Iri bhatani rinosanganisira 3 basa mavara: Channel marongero, frequency mita, uye system. Iyo yakasimbiswa label (yepakati peiyo label igrey uye font yakachena yakachena) ine inoenderana sub label pazasi pechiratidziro.
Manual Trigger Bhatani
Setting trigger, uye kuita manual trigger kana uchipenya.

Modulation/Frequency Meter Input Terminal/Trigger Output Terminal
Munguva ye AM, FM, PM kana PWM siginecha modulation, kana modulation sosi iri kunze, modulation chiratidzo inoiswa kuburikidza nekunze modulation yekupinda. Kana frequency meter ichishanda, chiratidzo chinoyerwa chinoiswa kuburikidza neiyi interface; kana bhuku rekutanga rechiratidzo chechanera ragoneswa, chiratidzo chekusimudzira chinobuda kuburikidza neiyi interface.
Synchronous Output Terminal
Iri bhatani rinotonga kuti rakavhurika rinobuda kana kuti kwete.

CH Kudzora/ Kubuda
Kubuda kwechiteshi kunogona kubatidzwa/kudzima nekukasira nekudzvanya bhatani reChannel, zvakare inogona kusetwa nekudzvanya Utility bhatani kuti up-up iyo label, wobva wadzvanya Channel Setting softkey.
Mabhatani ekutungamirira
Paunenge uchiseta parameter, famba kuruboshwe uye kurudyi kuti uchinje nhamba bit.
Multifunctional Knob uye Bhatani
Tenderedza bhatani rinoshanda kuti uchinje nhamba (tenderedza wachi uye nhamba dzichiwedzera) kana shandisa bhatani rinoshanda sebhatani rekutungamira. Dzvanya iyo multifunctional knob kuti usarudze basa, isa paramita uye simbisa kusarudzwa.
Nhamba Keyboard
Nhamba kiyibhodhi inoshandiswa kuisa parameter nhamba 0 kusvika 9, decimal point "." uye kiyi yechiratidzo “+/-”. Decimal point inogona kuchinja mayunitsi nekukurumidza.
Bhatani reMenu
3 basa mavara anozobuda nekudzvanya bhatani remenyu: Waveform, Modulation, uye Sweep. Dzvanya iyo inoenderana menyu function softkey kuti uwane basa rayo.
Inoshanda Menyu Softkeys
Kusarudza basa menyu nekukurumidza

2.2.2 Rear Panel
Iyo pani yekumashure inoratidzwa mumufananidzo 2-2:

USB Interface
PC software yakabatana kuburikidza neiyi USB interface.
Makomba Ekupisa Kupisa
Kuti uone kuti chiridzwa ichi chinobvisa kupisa zvakanaka, ndapota usavhare maburi aya.
Inishuwarenzi Pipe
Kana AC yekupinda ikozvino yadarika 2A, fuse inocheka iyo AC yekuisa kuchengetedza mudziyo.
Main Simba Chinja
Dzvanya pasi pa "Ini" kuti usimbise chiridzwa, uye dzvanya pasi pakanzi "O" kugura AC yekuisa.
AC Power Input Terminal
Mudziyo uyu unotsigira AC simba kubva pa100V kusvika 240V, 45Hz kusvika 440 Hz, uye simba rakasanganiswa i250V, T2 A.

2.2.3 Mubatanidzwa Webasa
Basa rekushanda rinoratidzwa mumufananidzo 2-3:

Tsanangudzo Yakadzama:

Ruzivo rwechiteshi: 1) "ON / OFF" kuruboshwe inzira yakavhurika ruzivo. 2) Pane "Limit" logo inoratidza inobuda muganho wepakati apo chena inoshanda uye grey haina basa. Iyo inofananidzwa impedance yekubuda terminal (1Ω kusvika 1KΩ inogadziriswa, kana yakakwirira kuramba, fekitori default ndeye 50Ω). 3) Rutivi rwerudyi ndiyo ikozvino inoshanda waveform.
Softkey labels: Softkey labels anoshandiswa kuratidza menyu softkey mabasa uye menyu mashandiro e softkey.
1) Mabhii ari kurudyi kwechidzitiro: Kuratidzwa kwakasimudzwa kunoratidza kuti iyo label yakasarudzwa. Kana zvisina kudaro, dzvanya softkey inoenderana kusarudza.
2) Mabhii pazasi pechidzitiro: Sub label zvirimo ndezvechikamu chinotevera cheType label. Dzvanya bhatani rinoenderana kuti usarudze sub labels.

Waveform Parameter Rondedzero: Inoratidza paramita yeazvino waveform mune runyorwa.
Waveform Display Area: Inoratidza yazvino chiteshi's waveform.

Chitsauko 3 Quick Start

3.1 General Inspection
Zvinokurudzirwa kutevera matanho ari pasi apa kuti utarise chiridzwa usati washandisa chigadzirwa ichi kekutanga.
3.1.1 Tarisa kune Kukuvadzwa Kunokonzerwa nekutakura
Kana katoni yekurongedza kana macushion epurasitiki efoam akakuvadzwa zvakanyanya, ndapota taura neUNI-T muparidzi wechigadzirwa ichi nekukurumidza.
Kana chiridzwa chakakuvadzwa nekutakura, ndapota chengeta pasuru uye ubate dhipatimendi rekutakura uye UNI-T muparidzi, muparadzi acharonga kugadzirisa kana kutsiva.
3.1.2 Tarisa Zvishandiso
UTG1000 accessories ndeiyi: Tambo yemagetsi, USB data tambo, BNC tambo (1 mita), uye mushandisi CD.
Kana chimwe chezvishandiso chisipo kana kukuvara, ndapota taura neUNI-T kana vaparadzi venzvimbo yechigadzirwa ichi.
3.1.3 Kuongorora kweMichina
Kana chiridzwa ichi chichiita sechakanganisika, chisiri kushanda nemazvo, kana chatadza bvunzo yekushanda, ndapota taura neUNI-T kana vaparadzi venzvimbo yechigadzirwa ichi.
3.2 Bata Kugadzirisa
UTG1000 yakatevedzana mubato inogona kugadziriswa zvakasununguka. Kana nzvimbo yekubata ichida kuchinjwa, ndapota bata mubato

3.3 Basic Waveform Output
3.3.1 Frequency Setting
Default waveform: Sine wave ye1kHz frequency uye 100mV amplitude (ine 50Ω kugumisa).
Matanho ekushandura frequency kusvika 2.5MHz anoratidzwa seanotevera:
a) Dzvanya Menyu → Waveform → Parameter → Frequency uchichinjana kune frequency kuseta modhi. Seta ma parameter nekudzvanya Frequencysoftkey kuti uchinje frequency uye nguva.
b) Shandisa nhamba keyboard kuisa nhamba inodiwa ye2.5.

c) Sarudza inoenderana unit MHz.
3.3.2 AmpLitude Setting
Defaultwaveform: Sine wave ye100mV peak-peak value ine 50Ω kugumiswa.
Matanho ekuchinja the amplitude kusvika 300mV inoratidzwa seinotevera:

Dzvanya Menyu → Waveform → Parameter→Amplitude pamwe chete. Press Amplitudesoftkey zvakare inogona kuchinja pakati peVpp, Vrms, uye dBm.
Shandisa makiyi enhamba kuisa mazana matatu.
Sarudza inodiwa unit: Dzvanya unit softkeymVpp.
Ongorora: Iyi parameter inogona kusetwa ne multifunctional knob uye mabhatani ekutungamira.

3.3.3 DC Offset Voltage Setting
Iyo default waveform ndeye sine wave ine 0V DC inobvisa voltage (ine 50Ω kugumiswa). Matanho ekuchinja DC offset voltage kusvika -150mV anoratidzwa seanotevera:

Dzvanya Menyu → Waveform → Parameter → Offset kuti uise parameter marongero.
Shandisa makiyi enhamba kuisa nhamba inodiwa ye -150.

Sarudza inoenderana unit mV.
Ongorora: Iyi parameter inogona kusetwa ne multifunctional knob uye mabhatani ekutungamira.

3.3.4 Square Wave Setting
Dzvanya Menyu → Waveform → Type → Squarewave → Parameter wobva wadzvanya Typesoftkey kuti usarudze chete kana Type label isina kuratidzwa. Kana parameter ichida kusetwa, baya kiyi inowirirana kuti uise nhamba inodiwa uye sarudza chikwata.

Cherechedza: Iyi parameter inogona kusetwa ne-multifunctional knob uye mabhatani ekutungamira.
3.3.5 Pulse Wave Setting
Default duty cycle ye pulse wave ndeye 50% uye kusimuka / kudonha kumucheto nguva ndeye 1us. Matanho ekuseta square wave ine 2ms nguva, 1.5Vpp amplitude, 0V DC offset uye 25% duty cycle (yakaganhurirwa neiyo shoma pulse hupamhi yakatarwa 80ns), 200us inosimuka nguva uye 200us inodonha nguva inoonekwa seinotevera:
Dzvanya Menyu → Waveform → Type → PulseWave → Parameter wobva wadzvanya Frequencysoftkey kuti uchinje kuPeriod.
Isa inodiwa nhamba kukosha uye sarudza chikwata. Paunenge uchipinda muduty cycle value, pane yekukurumidza label pazasi pekuratidzira, uye sarudza 25%.
Kana uchida kuseta inodonha nguva, tinya Parametersoftkey kana kutenderedza multifunctional knob kurudyi kuti uise sub label, wobva wadzvanya Falling Edgesoftkey kuisa nhamba inodiwa uye sarudza unit.

3.3.6 DC Voltage Setting
Chaizvoizvo, DC voltage kubuda ndiko kuseta kweDC offset. Matanho ekuchinja DC offset voltage kusvika ku3V inoonekwa seinotevera:

Dzvanya Menyu → Waveform → Type → DC wobva waisa parameter yekuseta modhi.

Shandisa nhamba keyboard kuisa nhamba inodiwa ye3.
Sarudza inodiwa unit V
Ongorora: Iyi parameter inogona kusetwa ne multifunctional knob uye mabhatani ekutungamira.

3.3.7 Ramp Wave Setting
Default symmetry degree re ramp wave iri 100%. Matanho ekuseta triangular wave ine 10kHz frequency, 2V amplitude, 0V DC inogadziriswa uye 50% yebasa kutenderera inoonekwa seinotevera:
Dzvanya Menyu → Waveform → Type → RampWave → Parameterwo kuti uise parameter yekumisikidza modhi. Sarudza parameter kuti uise edit mode, wozoisa nhamba dzinodiwa uye sarudza unit. Cherechedza: Kana waisa kukosha kwedhigirii resymmetry, pane 50% label pazasi pechiratidziro, dzvanya kiyi yakapfava inoenderana kana shandisa nhamba keyboard.

Cherechedza: Iyi parameter inogona kusetwa ne-multifunctional knob uye mabhatani ekutungamira.
3.3.8 Noise Wave Setting
Default Quasi Gauss ruzha amplitude ndeye 100mVpp uye DC offset ndeye 0mV. Matanho ekuseta Quasi Gauss ruzha ne300mVpp amplitude uye 1V DC offset inoratidzwa seinotevera:
Dzvanya Menyu → Waveform → Type → Ruzha → Parameta kuti uise parameter editing mode. Mushure mekugadzirisa, isa nhamba inodiwa uye unit.

Cherechedza: Iyi parameter inogona kusetwa ne-multifunctional knob uye mabhatani ekutungamira.
3.4 Frequency Kuyera
Ichi chishandiso chakakodzera kuyera frequency uye basa kutenderera kweTTL inoenderana masaini, ine frequency renji ye1Hz kusvika 100MHz. Iyo frequency mita inotora chiratidzo kuburikidza neyekupinza interface (Input / CNT terminal). Dzvanya Utility ipapo Counter kuti utore kukosha kwe Frequency, Period, uye Duty Cycle kubva pakuisa chiratidzo. Ongorora: Kana pasina chiratidzo chekuisa, frequency meter parameter runyorwa runogara ruchiratidza kukosha kwekupedzisira kuyerwa. Frequency mita inozovandudza chete kana chiratidzo chitsva cheTTL chiripo paInput/CNT terminal.

3.5 Build-in Help System
Iyo yekuvaka-mukati yekubatsira sisitimu inopa ruzivo rwakakodzera kune chero bhatani kana menyu softkey. Iwe zvakare unogona kushandisa rubatsiro rwemusoro runyorwa kuti uwane rubatsiro. Mashandisirwo emabhatani ekubatsira ruzivo anoratidzwa seanotevera:
Dzvanya kwenguva refu chero softkey kana bhatani kuratidza ruzivo rwakakodzera. Kana zvirimo zvinopfuura 1 skrini saizi, shandisa softkey kana multifunctional knob kuratidza chidzitiro chinotevera. Dzvanya "Return" kuti ubude.

Cherechedza!
Iyo yakavakirwa-mukati yekubatsira sisitimu inopa yakareruka yeChinese neChirungu mitauro. Ruzivo rwese, rubatsiro rwemamiriro ezvinhu uye musoro wekubatsira zvinoratidzwa mumutauro wakasarudzwa. Kurongeka kwemutauro: Utility→ Sisitimu→Mutauro.

Chitsauko 4 Advanced Applications

4.1 Modulation Waveform Output
4.1.1 AmpLitude Modulation (AM)
Dzvanya Menyu → Modulation → Type→ Amplitude Modulation zvakare kutanga iyo AM basa. Ipapo iyo modulated waveform inoburitsa ine modulation waveform uye inotakura wave set.

Mutakuri Waveform Sarudzo
AM inotakura waveform inogona kuva: sine wave, square wave, ramp wave kana arbitrary wave (kunze kwe DC), uye iyo yakasarudzika ndeye sine wave. Mushure mekusarudza AM modulation, dzvanya Carrier Wave Parameter nyoro kiyi yekuisa inotakura waveform yekusarudza interface.

Carrier Wave Frequency Setting
Settable carrier wave frequency range yakasiyana kune akasiyana anotakura waveforms. Default frequency yeese carrier wave ndeye 1kHz. Iyo frequency kuseta renji yega yega inotakura wave inogona kuoneka mune inotevera tafura:

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	1pHz	10MHz	1pHz	5MHz
Square wave	1pHz	5MHz	1pHz	5MHz	1pHz	5MHz
Ramp Wave	1pHz	400kHz	1pHz	400kHz	1pHz	400KHz
Arbitrary Wave	1pHz	3MHz	1pHz	2MHz	1pHz	1MHz

Kana uchida kuseta frequency yekutakura, ndapota tinya Parameter→ Frequencysoftkey, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit mushure mekusarudza mutakuri waveform.
Modulation Source Sarudzo
Ichi chishandiso chinogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa AM basa, iyo default modulation sosi ndeyemukati. Kana uchida kushandura dzvanya Parameter → ModulationSource → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, modulation wave inogona kuve: sine wave, square wave, kusimuka ramp wave, kudonha ramp masaisai, masaisai asingadiwi uye ruzha. Mushure mekugonesa AM basa, iyo default modulation wave ndeye sine wave. Kana zvichidiwa kuti uchinje, dzvanya Carrier Wave →Parameter→Taipa uchitevera.
 Square wave: basa kutenderera i50%
 Kusimuka Ramp Wave: symmetry degree ndeye 100%
 Kudonha Ramp Wave: symmetry degree ndeye 0%
 Arbitrary Wave: kana mafungu anopokana akagadziridzwa waveform, DDS basa jenareta rinomisa risingawirirane wave kureba se 1kpts munzira yekusarudzika kusarudzwa.
 Ruzha: White Gauss ruzha
Kunze Kwakabva
Kana modulation sosi iri yekunze, parameter runyorwa ruchavanza iyo modulation wave sarudzo uye modulation frequency sarudzo, uye mutakuri waveform inozogadziriswa nekunze waveform. AM kudzika kwemodulation inodzorwa ne ± 5V siginecha nhanho yekunze yekuisa modulation terminal. For example, kana modulation kudzika kukosha kwakaiswa ku100%, AM kubuda amplitude ndiyo yakanyanya kana yekunze modulation siginecha iri +5V, AM kubuda amplitude ndiyo ishoma kana chiratidzo chemodulation chekunze chiri -5V.

Modulation Shape Frequency Setting
Kana modulation sosi iri yemukati, frequency ye modulation chimiro inogona kugadziridzwa. Mushure mekugonesa AM basa, huwandu hwemodulation wave frequency ndeye 2mHz ~ 50kHz (default ndeye 100Hz). Dzvanya Parameter→ Modulation Frequency kuti chinja. Kana modulation sosi iri yekunze, rondedzero yeparameta inovanza iyo modulation chimiro sarudzo uye modulation frequency sarudzo, uye inotakura waveform ichagadziriswa nekunze waveform. Uwandu hwemodulation chiratidzo chekuisa kubva kunze ndeye 0Hz~ 20Hz.
Modulation Depth Setting
Modulation kudzika kunoratidza kuwanda kwe amplitude musiyano uye inoratidzwa sepercencetage. Yakakodzera kuseta huwandu hwe AM modulation kudzika ndeye 0% kusvika 120%, uye default ndeye 100%. Kana kudzika kwemodulation kwakaiswa ku0%, iyo inogara iripo amplitude (hafu yemutakuri wave amplitude that has set) inobuda. Output amplitude inoshanduka sezvo modulation waveform inoshanduka kana kudzika kwemodulation kwakaiswa ku100%. Chiridzwa chinoburitsa peak-peak voltage isingasviki ±5V (yakabatana ne50Ω terminal) kana kudzika kwemodulation kuchipfuura 100%. Kana uchida kuchinja, tinya Parameter → Modulation Depth in amplitude function interface. Kana modulation sosi iri kunze, kubuda amplitude yechiridzwa inodzorwa ne ± 5V siginecha yezinga rekunze modulation yekuisa terminal (Input/CNT probe) mune yekumashure. For example, kana modulation kudzika kukosha mune parameter runyorwa yakaiswa ku100%, AM kubuda amplitude ndiyo yakanyanya kunaka kana chiratidzo chekunze chiri +5V, AM kubuda amplitude ndiyo ishoma kana chiratidzo chekunze chemodulation chiri -5V.

Comprehensive Example
Kutanga, ita kuti chiridzwa chishande mukati amplitude modulation (AM) modhi, wozoisa sine wave ine 200Hz kubva mukati mechiridzwa sechiratidzo chemodulation uye square wave ine frequency ye10kHz, amplitude of
200mVpp uye basa kutenderera kwe45% sechiratidzo chekutakura wave. Pakupedzisira, isa modulation kudzika kusvika 80%. Matanho chaiwo anoonekwa seanotevera:

Enable AmpLitude Modulation (AM) Basa
Dzvanya Menyu → Modulation → Type→Amplitude Modulation pamwe chete.
Seta Modulation Signal Parameter
Mushure mekugonesa iyo AM basa, tinya Parametersoftkey uye iyo interface ichaonekwa seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.

Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Square Wave kuti usarudze square wave sechiratidzo chekutakura wave.
Dzvanya Parametersoftkey zvakare, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Seta Modulation Depth
Mushure mekuseta carrier wave parameter, tinya Returnsoftkey kudzoka kune inotevera interface yekuseta kudzika kwemodulation.Dzvanya Parameter → Modulation Degreesoftkey zvakare, wobva waisa nhamba 80 wodzvanya % softkey ine nhamba keyboard yekuseta kudzika kwemodulation.

4.1.2 Frequency Modulation (FM)
Mune frequency modulation, modulated waveform inowanzo umbwa inotakura wave uye modulation chimiro. Carrier wave frequency ichachinja se amplitude of modulation shape shanduko.
Dzvanya Menyu → Modulation → Type → Frequency Modulation kuti utange basa reFM. Chishandiso chinoburitsa modulated waveform ine modulation waveform uye inotakura wave set parizvino.

Mutakuri Wave Waveform Sarudzo
FM inotakura waveform inogona kuve: Sine wave, square wave, ramp wave, pulse wave, arbitrary wave (kunze kweDC) uye ruzha (iyo yakasarudzika ndeye sine wave). Mushure mekusarudza FM modulation, tinya Carrier Wave Parameter nyoro kiyi yekuisa inotakura waveform yekusarudza interface.

Carrier Wave Frequency Setting
Settable carrier wave frequency renji yakasiyana neyakasiyana inotakura waveform. Default frequency yeese carrier wave ndeye 1kHz. Iyo frequency kuseta renji yega yega inotakura wave inogona kuoneka mune inotevera tafura:

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	liiHz	10MHz	liiHz	5MHz
Square wave	1pHz	5MHz	liiHz	5MHz	1pHz	5MHz
Ramp Wave	1pHz	400kHz	liiHz	400kHz	1pHz	400KHz
Arbitrary Wave	1pHz	3MHz	liiHz	2MHz	1pHz	1MHz

Dzvanya Parameter → Frequencysoftkiyi kuti uise mutakuri wave frequency, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
Ichi chishandiso chinogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa FM basa, iyo default modulation sosi ndeyemukati. Kana zvichidiwa kuchinja, dzvanya

Yemukati Sosi
Kana modulation sosi iri yemukati, modulation wave inogona kuve: sine wave, square wave, kusimuka ramp wave, kudonha ramp masaisai, masaisai asingadiwi uye ruzha. Mushure mekugonesa FM basa, iyo default modulation wave ndeye sine wave. Kana uchida kuti uchinje, dzvanya Carrier Wave →Parameter→Taipa uchitevera.
 Square wave: basa kutenderera i50%
 Mutungamiriri Ramp Wave: symmetry degree ndeye 100%
 Muswe Ramp Wave: symmetry degree ndeye 0%
 Arbitrary Wave: Arbitrary wave kureba muganho ndeye 1kpts
 Ruzha: White Gauss ruzha
Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. FM frequency kutsauka inodzorwa ne ± 5V siginecha nhanho yekunze modulation yekuisa terminal pane kumberi kwepaneru. Mune yakanaka chiratidzo nhanho, FM inobuda frequency inopfuura mutakuri wave frequency, nepo muine negative signal level, FM inobuda frequency ishoma pane inotakura wave frequency. Kuderera kwechiratidzo chekunze kune kutsauka kudiki. For example, kana frequency offset yakaiswa ku1kHz uye chiratidzo chekunze chemodulation chiri +5V, FM inobuda frequency ichave yazvino inotakura frequency plus 1kHz. Kana iyo yekunze modulation siginecha iri -5V, FM inobuda frequency ichave yazvino inotakura frequency minus 1kHz.

Modulation Shape Frequency Setting
Kana modulation sosi iri yemukati, frequency ye modulation chimiro inogona kugadziridzwa. Mushure mekugonesa FM basa, iyo default modulation chimiro frequency ndeye 100Hz. Kana uchida kuchinja, dzvanya Carrier Wave Parameter→ Modulation Frequency mukuchinjana, uye modulation frequency renji ndeye 2mHz kusvika 50kHz. Kana modulation sosi iri kunze, parameter rondedzero inovanza iyo modulation chimiro sarudzo uye modulation frequency sarudzo, uye mutakuri waveform inozogadziriswa nekunze waveform. Iyo mhando yemodulation chiratidzo chekuisa kubva kunze ndeye 0Hz kusvika 20Hz.
Frequency Deviation Setting
Frequency kutsauka kunomiririra mutsauko uripo pakati peiyo frequency yeFM yakagadziridzwa waveform uye inotakura frequency. Settable range yeFM frequency deviation inobva pa1μHz kusvika pahupamhi hweinotakura carrier wave frequency, uye kukosha kwekutanga i1kHz. Kana ichida kuchinja, dzvanya Parameter → Frequency Deviation nekuchinjana.

Frequency kutsauka ishoma pane carrier wave frequency. Kana frequency yekutsauswa kukosha ikakwidzwa kupfuura mutakuri wewave frequency, mudziyo unozoseta wotomatiki kukosha kuhuwandu hunobvumidzwa nemutakuri.
Sum of frequency deviation uye carrier wave frequency ishoma pane inotenderwa maximal frequency ezvino inotakura wave. Kana ukoshi hwefrequency kutsauswa ukaiswa paukoshi husingaite, mudziyo unozozviseta wotomati kukosha kweiyo kuhuwandu hunobvumirwa nemutakuri.

Comprehensive Example:
Ita kuti chiridzwa chishande mu frequency modulation (FM) modhi, wozoisa sine wave ine 2kHz kubva mukati mechiridzwa sechiratidzo chemodulation uye square wave ine frequency ye10kHz uye. amplitude ye100mVpp sechiratidzo chemutakuri wemasaisai. Pakupedzisira, isa frequency kutsauka kusvika ku5kHz. Matanho chaiwo anoonekwa seanotevera:

Gonesa Frequency Modulation (FM) Basa
Dzvanya Menyu → Modulation → Type → Frequency Modulation kuti utange basa reFM.
Seta Modulation Signal Parameter
Dzvanya Parametersoftkey. Ipapo iyo interface icharatidza seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Sine Wave kuti usarudze sine wave sechiratidzo chekutakura wave.
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inowirirana softkey kutanga, wobva waisa inodiwa nhamba kukosha, uye sarudza chikwata.

Seta Frequency Kutsauka
Mushure mekuisa carrier wave parameter, tinya Returnsoftkey kudzoka kune inotevera interface yekuseta frequency kutsauka.
Dzvanya Parameter → Frequency Deviation softkey, wobva waisa nhamba 5 wodzvanya kHzsoftkey ine nhamba keyboard yekuseta frequency kutsauka.
Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi.
Chimiro cheFM modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.1.3 Phase Modulation (PM)
Muchikamu chemodulation, modulated waveform inowanzo umbwa neyekutakura wave uye modulation wave. Chikamu chemutakuri wave chinoshanduka se amplitude of modulation shape shanduko.
Dzvanya Menyu → Modulation → Type→ Phase Modulation kuti utange iyo PM basa. Chishandiso chinoburitsa modulated waveform ine modulation waveform uye inotakura wave set parizvino. Mutakuri Wave Waveform Sarudzo
PM inotakura waveform inogona kuve: Sine wave, square wave, ramp wave kana arbitrary wave (kunze kwe DC), uye iyo yakasarudzika ndeye sine wave. Dzvanya Carrier Wave Parametersoftkiyi kuti usarudze mutakuri waveform.

Carrier Wave Frequency Setting
Settable carrier wave frequency renji yakasiyana neyakasiyana inotakura waveform. Default frequency yeese carrier wave ndeye 1kHz. Iyo frequency kuseta renji yega yega inotakura wave inogona kuoneka mune inotevera tafura:

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	1pHz	10MHz	1pHz	5MHz
Square wave	1pHz	5MHz	1pHz	5MHz	1pHz	5MHz
Ramp Wave	1pHz	400kHz	1pHz	400kHz	1pHz	400KHz

Dzvanya Parameter→ Frequencysoftkey kuti upinde mutakuri wave frequency kuseta, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
Ichi chishandiso chinogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa PM basa, iyo default modulation sosi ndeyemukati. Kana ichida kuchinja, dzvanya Parameter → ModulationSource → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, modulation chimiro chinogona kuve: sine wave, square wave, kusimuka ramp wave, kudonha ramp masaisai, masaisai asingadiwi uye ruzha. Mushure mekugonesa PM basa, iyo default modulation wave ndeye sine wave. Kana uchifanira kuchinja, dzvanya Carrier Wave Parameter→Taipa uchitevera.

Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. PM chikamu kutsauka kunodzorwa ne ± 5V siginecha nhanho yekunze modulation yekuisa terminal pane kumberi kwepaneru. For example, kana chikamu chekutsaudzira kukosha muparameter list yakaiswa ku 180º, +5V yechiratidzo chemodulation yekunze yakaenzana ne180º phase shift.

Modulation Shape Frequency Setting
Kana modulation sosi iri yemukati, frequency ye modulation chimiro inogona kugadziridzwa. Mushure mekugonesa PM basa, iyo default modulation chimiro frequency ndeye 100Hz. Kana ichida kuchinja, dzvanya Carrier Wave Parameter → Modulation Frequency mukuchinjana, uye modulation frequency renji ndeye 2mHz kusvika 50kHz. Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. Uwandu hwemodulation chiratidzo chekuisa kubva kunze ndeye 0Hz kusvika 20Hz.

Kutsauka kwechikamu kunoratidza shanduko pakati pechikamu chePM modulated waveform uye chikamu cheanotakura wave chikamu. Settable range yePM phase deviation inobva pa0º kusvika 360º, uye the default value is 50º. Kana uchida kuchinja, dzvanya Parameter→Phase Deviation wobva wachinja.
Comprehensive Example
Chekutanga, ita kuti chiridzwa chishande muchikamu chemodulation (PM) modhi, wozoisa sine wave ine 200Hz kubva mukati mechiridzwa sechiratidzo chemodulation uye sikweya ine frequency ye900Hz uye amplitude ye100mVpp sechiratidzo chemutakuri wemasaisai. Pakupedzisira, isa chikamu chekutsauka ku200º. Matanho chaiwo anoonekwa seanotevera:

Gonesa Phase Modulation (PM) Basa
Dzvanya Menyu → Modulation → Type → Phase Modulation kuti utange iyo PM basa.
Seta Modulation Signal Parameter
Dzvanya Parametersoftkey uye iyo interface icharatidza seinotevera:
Dzvanya inowirirana softkey kutanga, wobva waisa inodiwa nhamba kukosha, uye sarudza chikwata.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Sine Wave kuti usarudze sine wave sechiratidzo chekutakura wave.
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.

Seta Phase Kutsauka
Dzvanya Returnsoftkey kuti udzokere kune inotevera interface yekumisikidza chikamu modulation.
Dzvanya Parameter → Phase Deviationsoftkey, wobva waisa nhamba 200 wodzvanya ºsoftkey ine nhamba keyboard yekuseta chikamu chekutsauka.
Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi nekukurumidza.
Chimiro chePM modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.1.4 Amplitude Shift Keying (Bvunza)
ASK inomiririra chiratidzo chedhijitari "0" uye "1" nekuchinja amplitude of carrier wave signal. Carrier wave chiratidzo chakasiyana amplitude ichave inobuda pahwaro hweakasiyana mantiki emodulation chiratidzo.
Bvunza Modulation Selection
Dzvanya Menyu → Modulation → Type→Amplitude Shift Keying kuti utange iyo ASK basa, chishandiso chinoburitsa modulated waveform ine ASK chiyero uye inotakura wave yakaiswa parizvino.

Mutakuri Wave Waveform Sarudzo
Bvunza mutakuri waveform inogona kuva: Sine wave, square, ramp wave kana arbitrary wave (kunze kwe DC), uye iyo yakasarudzika ndeye sine wave. Dzvanya Carrier Wave Parameter nyoro kuti upinde mutakuri waveform yekusarudza interface.

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	liiHz	10MHz	liiHz	10MHz	liiHz	5MHz
Square wave	1pHz	5MHz	liiHz	5MHz	liiHz	5MHz
Ramp Wave	1pHz	400kHz	liiHz	400kHz	liiHz	400KHz
Arbitrary Wave	1pHz	3MHz	liiHz	2MHz	liiHz	1MHz

Dzvanya Parameter → Frequencysoftkey, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
Iyo mudziyo unogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa ASK basa, iyo default modulation sosi ndeyemukati. Kana ichida kuchinja, dzvanya Parameter → ModulationSource → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, yemukati modulation wave is square wave ye50% yebasa kutenderera (isina kuchinjika).
Iyo ASK chiyero inogona kusetwa kugadzirisa modulated waveform amplitude hopping frequency.
Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. Bvunza zvabuda amplitude inotemerwa neiyo logic level yemodulation interface pane yekumberi panhi. For example, inoburitsa iyo carrier wave amplitude yekumisikidza kwazvino kana yekunze yekuisa logic yakaderera, uye inobuda inotakura wave amplitude zvishoma pane amplitude yekumisikidza ikozvino kana yekunze yekuisa logic yakakwira.
Bvunza Rate Setting
Kana modulation sosi iri yemukati, frequency yeASK amplitude jump inogona kuchinjwa. Mushure mekugonesa basa reASK, mwero weASK unogona kusetwa uye iyo inogadzika renji i2mHz kusvika 100kHz, iyo default rate ndeye 1kHz. Kana uchida kuchinja, dzvanya Carrier Wave Parameter→Rate pamwe chete.

Comprehensive Example
Ita kuti chiridzwa chishande mukati amplitude shift keying (ASK) modhi, wozoisa chiratidzo chine 300Hz kubva mukati mechiridzwa sechiratidzo chemodulation uye sine wave ine frequency ye15kHz uye amplitude ye2Vpp sechiratidzo chemutakuri. Matanho chaiwo anoonekwa seanotevera:

Enable Amplitude Shift Keying (ASK) Basa
Dzvanya Menyu → Modulation → Type→Amplitude Shift Keying zvakare kuti utange iyo ASK basa.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Sine Wave pamwe chete
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.

Seta ASK Rate
Mushure mekuseta carrier wave parameter, dzvanya Returnsoftkey kuti udzokere kune inotevera interface yekuseta chikamu modulation.
Dzvanya Parameter → Ratesoftkey zvakare, wobva waisa nhamba 300 wodzvanya Hzsoftkey ine nhamba keyboard yekuseta ASK rate.
Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi nekukurumidza.
Chimiro cheASK modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.1.5 Frequency Shift Keying (FSK)
Mu frequency shift keying, chiyero che carrier wave frequency uye hopping frequency inogona kuchinjwa.
FSK Modulation Sarudzo
PressMenu → Modulation → Type → Frequency Shift Keying wozotanga basa reFSK. Chishandiso chinoburitsa modulated waveform ine ikozvino kuseta.

Mutakuri Wave Waveform Sarudzo
Dzvanya Carrier Wave Parametersoftkiyi kuti upinde mutakuri waveform yekusarudza interface. FSK inotakura waveform inogona kuva: sine wave, square wave, ramp wave kana arbitrary wave (kunze kwe DC), uye iyo yakasarudzika ndeye sine wave.

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	liiHz	10MHz	1pHz	5MHz
Square wave	1pHz	5MHz	liiHz	5MHz	liiHz	5MHz
Ramp Wave	1pHz	400kHz	liiHz	400kHz	liiHz	400KHz
Arbitrary Wave	1pHz	3MHz	liiHz	2MHz	liiHz	1MHz

Dzvanya Parameter → Frequencysoftkey, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
Iyo mudziyo unogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa FSK basa, iyo default modulation sosi ndeyemukati. Kana ichida kuchinja, dzvanya Parameter → ModulationSource → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, yemukati modulation wave iri sikweya ye50% yebasa kutenderera (isina kuchinjika). Iyo FSK chiyero inogona kusetwa kugadzirisa iyo inofamba frequency pakati pemutakuri wave frequency uye hop frequency.
Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. FSK inobuda frequency inotarwa neiyo logic level yemodulation interface pane yekumberi panhi. For example, inoburitsa carrier wave frequency kana zvekunze zvinobuda zvadzikira, uye kubuda hop frequency kana zvekunze zvemapupu zvakakwirira.
Hop Frequency Setting

Mushure mekugonesa FSK basa, iyo default hop frequency ndeye 2MHz. Kana uchida kuchinja, dzvanya Parameter → Hop Frequency pamwe chete. Settable renji ye hop frequency inotemerwa nemutakuri wave waveform. Ona tafura inotevera yekuseta huwandu hwemutakuri wega wega frequency:

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	1pHz	10MHz	1pHz	5MHz
Square wave	1pHz	5MHz	1pHz	5MHz	1pHz	5MHz
Ramp Wave	1pHz	400kHz	1pHz	400kHz	1pHz	400KHz
Arbitrary Wave	1pHz	3MHz	1pHz	2MHz	1pHz	1MHz

FSK Rate Setting
Kana modulation sosi iri yemukati, iyo inofambisa frequency pakati pemutakuri wave frequency uye hop frequency inogona kusetwa. Mushure mekugonesa basa reFSK, FSK rate inogona kusetwa uye iyo inogadzika renji i2mHz kusvika 100kHz, iyo default rate ndeye 1kHz. Kana uchida kuchinja, dzvanya Carrier Wave Parameter → Rate pamwe chete.
Comprehensive Example
Chekutanga, ita kuti chiridzwa chishande mu frequency shift keying (FSK) modhi, wozoseta sine wave ine 2kHz uye 1Vpp kubva mukati mechiridzwa seyekutakura wave chiratidzo, uye isa hop frequency kusvika 800 Hz, pakupedzisira, ita carrier wave frequency. uye hop frequency inofamba pakati peumwe neumwe ne 200Hz frequency. Matanho chaiwo anoonekwa seanotevera:

Gonesa Frequency Shift Keying (FSK) Basa
Dzvanya Menyu → Modulation → Type → Frequency Shift Keying wobva watanga basa reFSK.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Sine Wave kuti usarudze sine wave semutakuri wave.
Dzvanya Parametersoftkey zvakare, uye iyo interface ichabuda seinotevera:
Dzvanya inowirirana softkey kutanga, wobva waisa inodiwa nhamba kukosha, uye sarudza chikwata.

Seta Hop Frequency uye FSK Rate
Dzvanya Returnsoftkey kuti udzokere kune inotevera interface.
Dzvanya Parametersoftkey zvakare, uye iyo interface ichabuda seinotevera:
Dzvanya inowirirana softkey kutanga, wobva waisa inodiwa nhamba kukosha, uye sarudza chikwata.
Gonesa Channel Output
Dzvanya bhatani reChannel pane yekumberi kuti uvhure chiteshi chinobuda.
Chimiro cheFSK modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.1.6 Phase Shift Keying (PSK)
Muchikamu chekuchinja keying, DDS basa jenareta rinogona kugadzirwa kuti rifambe pakati pezvikamu zviviri zvakagadzirirwa (mutakuri wechikamu uye modulation phase). Output carrier wave signal phase kana hop signal phase pahwaro hweiyo logic yemodulation signal.
PSK Modulation Sarudzo
Dzvanya Menyu → Modulation → Type → Phase Shift Keying uye kutanga iyo PSK basa. Chishandiso chinoburitsa modulated waveform ine carrier wave phase (iyo default ndeye 0º uye haigadzirike) yekumisikidzwa kwazvino uye modulation chikamu.

Mutakuri Wave Waveform Sarudzo
PSK inotakura waveform inogona kuva: Sine wave, square, ramp wave kana arbitrary wave (kunze kwe DC), uye iyo yakasarudzika ndeye sine wave. Dzvanya Carrier Wave Parametersoftkiyi kuti upinde mutakuri waveform yekusarudza interface.

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	1pHz	10MHz	1pHz	5MHz
Square wave	1pHz	5MHz	1pHz	5MHz	1pHz	5MHz
Ramp Wave	1pHz	400kHz	1pHz	400kHz	1pHz	400KHz

Dzvanya Parameter → Frequencysoftkey, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
UTG1000A basa / inopokana waveform jenareta inogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Mushure mekugonesa PSK basa, iyo default modulation sosi ndeyemukati. Kana uchida kuchinja, dzvanya Parameter → Modulation → Mabviro → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, yemukati modulation wave is square wave ye50% yebasa kutenderera (isina kuchinjika).
Iyo PSK chiyero inogona kusetwa kugadzirisa iyo inofamba frequency pakati pemutakuri wave chikamu uye modulation chikamu.
Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura waveform inogadziriswa neyekunze waveform. Carrier wave phase ichabuda kana zvekunze logic zvadzikira, uye modulation phase ichabuda kana zvekunze zvemapupu zvakwira.

PSK Rate Setting
Kana modulation sosi iri yemukati, iyo inofamba frequency pakati pemutakuri wave chikamu uye modulation chikamu inogona kusetwa. Mushure mekugonesa basa rePSK, chiyero chePSK chinogona kusetwa uye iyo inogadzika renji i2mHz kusvika 100kHz, iyo default rate ndeye 100Hz. Kana uchida kuchinja, dzvanya Carrier Wave Parameter → Rate pamwe chete.
Modulation Phase Setting
Modulation phase inoratidza shanduko pakati pechikamu chePSK modulated waveform uye chikamu cheanotakura wave chikamu. Settable renji yePSK chikamu kubva pa0º kusvika 360º, uye iyo default kukosha ndeye 0º. Kana uchida kuchinja, dzvanya Parameter→Chikamu chinjana.
Comprehensive Example
Ita kuti chiridzwa chishande muchikamu chekuchinja keying (PSK) modhi, wozoisa sine wave ine 2kHz uye 2Vpp kubva mukati mechiridzwa sechiratidzo chekutakura mafungu, pakupedzisira, ita carrier wave phase uye modulation phase kufamba pakati peumwe neumwe ne 1kHz frequency. . Matanho chaiwo anoonekwa seanotevera:

Gonesa Phase Shift Keying (PSK) Basa
Dzvanya Menyu → Modulation → Type → Phase Shift Keying uye kutanga iyo PSK basa.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter → Type → Sine Wave kuti usarudze sine wave sechiratidzo chekutakura wave.
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Seta PSK Rate uye Modulation Phase
Dzvanya Returnsoftkey kuti udzokere kune inotevera interface:
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.

Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi nekukurumidza.
Chimiro chePSK modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.1.7 Pulse Width Modulation (PWM)
Mune pulse wide modulation, modulated waveform inowanzo umbwa neyekutakura wave uye modulation chimiro, uye pulse hupamhi hweanotakura wave inoshanduka semodulation chimiro. ampshanduko yezvidzidzo.
PWM Modulation Sarudzo
Dzvanya Menyu → Modulation → Type → Pulse Width Modulation kuti utange iyo PWMK basa. Chishandiso chinoburitsa modulated waveform ine modulation waveform uye inotakura wave yekumisikidzwa kwazvino. Mutakuri Wave Waveform
PWM inotakura wave waveform inogona kungove pulse wave. Mushure mePWM modulation, dzvanya mutakuri parametersoftkiyi kuti upinde mutakuri waveform yekusarudza interface, zvino zvinogona kuoneka kuti Pulse Wave label inosarudzwa otomatiki.

Carrier Wave Frequency Setting
Inogadzika huwandu hwepulse wave frequency inobva pa500uH kusvika 25MHz, uye iyo default frequency ndeye 1kHz. Dzvanya Parameter→ Frequency softkey kuti uchinje frequency, wobva waisa inodiwa manhamba kukosha, uye sarudza unit.
Carrier Wave Duty Cycle Setting
Settable range ye pulse wave duty cycle ndeye 0.01% ~ 99.99%, uye default duty cycle i50%. Dzvanya Parameter→ Frequencysoftkey kuti uchinje, wobva waisa kukosha kwenhamba inodiwa, uye sarudza unit.
Modulation Source Sarudzo
Iyo mudziyo unogona kusarudza yemukati modulation sosi kana yekunze modulation sosi. Kana ichida kuchinja, dzvanya Parameter → ModulationSource → Yekunze mukuchinjana.

Yemukati Sosi
Kana modulation sosi iri yemukati, modulation wave inogona kuve: sine wave, square wave, kusimuka ramp wave, kudonha ramp wave, zvechisimba wave uye ruzha, uye iyo default wave ndeye sine wave. Kana uchida kuchinja, dzvanya Carrier Wave ParameterModulation Waveform pamwe chete.
 Square wave: basa kutenderera 50%
 Mutungamiriri Ramp Wave: symmetry degree ndeye 100%
 Muswe Ramp Wave: symmetry degree ndeye 0%
 Arbitrary Wave: Arbitrary wave kureba muganho ndeye 1kpts
 Ruzha: White Gauss ruzha
Kunze Kwakabva
Kana modulation sosi iri yekunze, inotakura wave waveform inogadziriswa neyekunze waveform.
Modulation Shape Frequency Setting
Kana modulation sosi iri yemukati, frequency ye modulation wave inogona kugadziridzwa (renji ndeye 2mHz ~ 20kHz). Mushure mekugonesa PWM basa, iyo default modulation wave frequency ndeye 1kHz. Kana uchida kuchinja, dzvanya Carrier Wave Parameter → Modulation Frequency pamwe chete. Kana modulation sosi iri kunze, carrier wave waveform (pulse wave) inogadziriswa neyekunze waveform. Iyo mhando yemodulation chiratidzo chekuisa kubva kunze ndeye 0Hz kusvika 20kHz.

Duty Cycle Deviation Setting
Kutsauka kwebasa kunomiririra mutsauko uripo pakati pebasa rekutenderera kweiyo modulated waveform uye yezvino inotakura basa kutenderera. Settable range yePWM duty cycle inobva pa0% kusvika 49.99%, uye iyo default value i20%. Kana uchida kuchinja, dzvanya Parameter→Duty Cycle Deviation wobva wachinja.

Basa rekutenderera kutenderera rinomiririra mutsauko uripo pakati pebasa rekutenderera kweiyo modulated waveform uye yebasa kutenderera kweyekutanga pulse waveform, inomiririrwa mu%.
Duty cycle deviation haigoni kudarika basa rekutenderera kwezvino pulse wave.
Sum of duty cycle deviation uye yazvino pulse wave duty cycle haifanire kudarika 99.99%.

Duty cycle deviation inogumira nedikidiki rebasa kutenderera kwepulse wave uye ikozvino kumucheto nguva.

Comprehensive Example
Ita kuti chiridzwa chishande mu pulse modulation (PWM) modhi, wozoisa sine wave ine 1kHz kubva mukati mechiridzwa sechiratidzo chemodulation uye pulse wave ine 10kHz frequency, 2Vpp. amplitude uye 50% duty cycle sea carrier wave signal, pakupedzisira, isa duty cycle kutsauka ku40%. Matanho chaiwo anoonekwa seanotevera:

Gonesa Pulse Width Modulation (PWM) Basa
Dzvanya Menyu → Modulation → Type → Pulse Width Modulation kuti utange iyo PWM basa.
Seta Modulation Signal Parameter
Dzvanya Parameter softkey uye iyo interface icharatidza seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Seta Mutakuri Wave Signal Parameter
Dzvanya Carrier Wave Parameter nyoro kiyi yekupinda mutakuri wave parameter kuseta interface.
Dzvanya Parameter softkey, uye iyo interface ichabuda seinotevera:
Kana uchida kuseta parameter, dzvanya nyoro nyoro yekutanga, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Isa Duty Cycle Kutsauka
Dzvanya Returnsoftkey kuti udzokere kune inotevera interface yebasa cycle kutsauka kuseta:
Mushure mekudzvanya Parameter → Dutycyclesoftkiyi, isa nhamba 40 uye tinya % softkey ine nhamba keyboard yekuseta duty cycle kutsauka.
Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi nekukurumidza.
Chimiro chePWM modulation waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.2 Kutsvaira Waveform Output
Mune yekutsvaira modhi, frequency inobuda mumutsara kana logarithmic nzira panguva yakatarwa yekutsvaira nguva. Trigger sosi inogona kunge iri yemukati, yekunze kana yemanyorero inokonzeresa; uye sine wave, square wave, ramp wave uye arbitrary wave (kunze kweDC) inogona kuburitsa kutsvaira.
4.2.1 Kutsvaira Sarudzo

Bvumira Basa Rokutsvaira
Dzvanya bhatani reMenu kutanga, wobva wadzvanya Sweepsoftkey kuti utange kutsvaira. Chishandiso chinoburitsa sweep waveform ine ikozvino kuseta.
Kutsvaira Waveform Sarudzo
Dzvanya Mutakuri Parametersoftkey kusarudza kutsvaira waveform, ipapo iyo interface inobuda icharatidza seinotevera:

4.2.2 Tanga Frequency uye Stop Frequency Setting
Kutanga frequency uye kumisa frequency ndiwo muganho wepamusoro uye wakaderera muganho wefrequency scanning. Dzvanya Returnsoftkey kuti udzokere kutsvaira interface. Dzvanya Parameter→ Tanga Frequency→StopFrequencysoftkeys mochinjana, wobva waisa nhamba ine nhamba kiibhodhi wodzvanya kiyi inowirirana.

Kana yekutanga frequency yakadzikira pane yekumira frequency, DDS basa jenareta rinotsvaira kubva kuzasi frequency kusvika yakakwira frequency.
Kana yekutanga frequency yakakwira kupfuura yekumira frequency, DDS basa jenareta rinotsvaira kubva pakakwirira frequency kusvika yakaderera frequency.
Kana yekutanga frequency yakaenzana nekumisa frequency, DDS basa jenareta inotsvaira yakabuda yakatarwa frequency.
Synchronous sign ye sweep mode chiratidzo chakadzikira kubva pakutanga kwekutsvaira kusvika pakati penguva yekutsvaira, uye iri pamusoro kubva pakati penguva yekutsvaira kusvika pakupera kwenguva yekutsvaira.

Iyo default yekutanga frequency ndeye 1kHz, uye yekumisa frequency ndeye 2kHz. Yakasiyana sweep waveform ine akasiyana anogadzika huwandu hwekugonesa uye kumisa frequency, inogadzika frequency renji yega yega yekutsvaira wave inoratidzwa mune inotevera tafura:

Mutakuri Wave	Frequency
	UTG1020A		UTG1010A		UTG1005A
	Minimum Value	Maximum Value	Minimum Value	Maximum Value	Minimum Value	Maximum Value
Sine Wave	1pHz	10MHz	liiHz	10MHz	liiHz	5MHz
Square wave	liiHz	5MHz	liiHz	5MHz	1pHz	5MHz
Ramp Wave	liiHz	400kHz	liiHz	400kHz	liiHz	400KHz
Arbitrary Wave	1pHz	3MHz	liiHz	2MHz	liiHz	1MHz

4.2.3 Kutsvaira Mode
Linear sweep: waveform jenareta inoshandura inobuda frequency munzira yemutsara panguva yekutsvaira; Logarithmic sweep: waveform jenareta inoshandura inobuda frequency nenzira ye logarithmic; Kutsvaira kwekunze, iyo yakasarudzika inzira yekutsvaira, kana ichifanira kuchinja, tapota tinya TypeLogarithmsoftkey.

4.2.4 Nguva yekutsvaira
Seta nguva inodiwa kubva kunguva yekutanga kuenda kune yekupedzisira frequency, iyo default ndeye 1s, uye iyo inogadzika renji inobva pa1ms kusvika 500s. Kana uchida kuchinja, dzvanya Parameter → Sweep Timesoftkey wobva waisa nhamba ine kiibhodhi yenhamba, wodzvanya kiyi inowirirana

4.2.5 Trigger Source Selection
Kana jenareta yechiratidzo inogamuchira chiratidzo chekusimudzira, inogadzira kubuda kwekutsvaira, uye yozomirira iyo inotevera trigger chiratidzo. Sweep sosi inogona kunge iri yemukati, yekunze kana yemanyorero inokonzeresa. Kana uchida kuchinja, dzvanya Parameter →Trigger Sourcesoftkey wobva wachinja.

Kana yemukati trigger yasarudzwa, waveform jenareta inoburitsa kutsvaira kunoramba kuripo, uye chiyero chinotarwa nenguva yekutsvaira.
Kana yekunze trigger yasarudzwa, waveform jenareta inokonzeresa kuburikidza nemodulation interface hardware.
Kana manual trigger yasarudzwa, backlight yeTrigger bhatani inopenya, dzvanya bhatani reTrigger kamwe chete, kutsvaira kuchabuda.

4.2.6 Kuburitsa Kuburitsa
Kana trigger sosi iri yemukati kana yemanyorero trigger, trigger siginecha (square wave) inogona kubuda kuburikidza nekunze modulation interface (Input/CNT probe). Iyo yekusarudzika ye trigger yekubuda sarudzo ndeye "Vhara". Kana ichida kuchinja, dzvanya Parameter→Trigger Output →Opensoftkiyi mochinjana.

Mune inokonzeresa yemukati, chiratidzo chejenareta chinoburitsa sikweya ye50% yebasa kutenderera kuburikidza nekunze modulation interface (Input/CNT probe) pakutanga kwekutsvaira.
Mumanyorero trigger, chiratidzo jenareta inoburitsa pulse ine pulse hupamhi kupfuura 1us kuburikidza nekunze modulation interface (Input / CNT probe) pakutanga kwekutsvaira.
Mune yekunze trigger, trigger inobuda inobuda kuburikidza nemodulation interface (Input/CNT probe), asi konzeresa sarudzo dzekubuda mune parameter runyorwa zvichavanzwa.

4.2.7 Zvakakwana Eksample
Mukutsvaira modhi, isa sine wave chiratidzo ne1Vpp amplitude uye 50% duty cycle sechiratidzo chekutsvaira, uye nzira yekutsvaira ndeyekutsvaira, isa iyo yekutanga frequency yekutsvaira kusvika ku1kHz uye terminal frequency kusvika 50kHz uye kutsvaira nguva kusvika 2ms.
Shandisa inokwira kumucheto inokonzeresa yemukati sosi kuburitsa sweep wave. Matanho chaiwo anoonekwa seanotevera:

Bvumira Basa Rokutsvaira
Dzvanya Menyu → Tsvaira → Nyora → Mutsetse wobva watanga kutsvaira.
Sarudza Sveep Waveform
Dzvanya Carrier Wave Paremeter → Type →Square Wavesoftkiyi kusarudza kutsvaira waveform, uye iyo interface ichabuda seinotevera:
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Seta Yekutanga / Terminal Frequency, Kutsvaira Nguva, Trigger Source uye Trigger Edge Press Returnsoftkey kune inotevera interface:
Dzvanya Parametersoftkey, uye iyo interface ichabuda seinotevera:
Dzvanya inoenderana softkey, wobva waisa inodiwa nhamba kukosha, uye sarudza iyo unit.
Gonesa Channel Output
Dzvanya bhatani reChannel kuti uvhure kubuda kwechiteshi nekukurumidza.
Chimiro chekutsvaira waveform yakatariswa kuburikidza neoscilloscope inoratidzwa seinotevera:

4.3 Arbitrary Wave Output
UTG1000A inochengetedza zvachose gumi nematanhatu marudzi eakajairwa waveforms, mazita ega ega waveform anogona kuwanikwa mutafura 16-4 (yakavakirwa-mukati-inopokana wave rondedzero).
4.3.1 Gonesa Arbitrary Wave Basa
Dzvanya Menyu → Waveform → Type → Arbitrary Wave kuti utange kuita zvehumbimbindoga wave basa. Chishandiso ichi chinoburitsa zvekupokana waveform ine yazvino kuseta.

4.3.2 Kusarudzika Wave Selection
Vashandisi vanogona kusarudza zvekupokana waveform mukati mechiridzwa. Dzvanya Parameter→ Arbitrary Wave Selectionsoftkiyi kuti usarudze inodiwa inopokana wave.

AbsSine	AmpALT	AttALT	Gaussian Monopulse
GaussPulse	SineVer	StairUd	Trapezia
LogNormalSinc	Sinc	Electrocardiogram	Electroencephalogram
Index Rises	Index Falls	Lorentz	D-Lorentz

Chitsauko 5 Dambudziko Kupfura

Matambudziko anogona kuitika uye dambudziko rekupfura nzira zvakanyorwa mukutevera. Ndapota tevera matanho ekugadzirisa matambudziko.
Kana usingakwanise kuzvibata, ndapota taura nevashambadzi vechigadzirwa ichi kana hofisi yemuno, uye ipawo ruzivo rwemidziyo yechiridzwa chako (nzira yekutora: dzvanya Utility →System →System→ About in turn).
5.1 Hapana Chiratidziro PaSikirini (Black Screen)
Kana bhatani remagetsi richidzvanywa uye oscilloscope iri dema skrini:
a) Tarisa kubatanidza kwemagetsi
b) Ita shuwa kuti switch yemagetsi pane yekumashure yabatidzwa uye yakaiswa ku "Ini"
c) Ita shuwa kuti switch yemagetsi yepanera yekumberi yakabatidzwa
d) Tangazve chiridzwa
5.2 Hapana Waveform Output
Mushure mekutora chiratidzo, waveform haioneke pachiratidziro:
① Tarisa kana BNC tambo yakabatana kune inobuda chiteshi
② Tarisa kana bhatani rekudzvanya Channel rakavhurika

Chitsauko 6 Masevhisi uye Zvitsigiro

6.1 Warranty Overview
Uni-T (Uni-Trend Technology (China) Ltd.) inovimbisa kugadzirwa uye kutengeswa kwezvigadzirwa, kubva pazuva rekutengesa rakabvumidzwa remutengesi wemakore matatu, pasina chakakanganisika mune zvekushandisa uye magadzirirwo. Kana chigadzirwa chikaonekwa kuti hachina kumira zvakanaka mukati menguva ino, UNI-T ichagadzirisa kana kutsiva chigadzirwa ichi zvinoenderana nezviri muwaranti.
Kuronga kugadzirisa kana kuwana fomu rewaranti, ndapota taura nedhipatimendi riri pedyo reUNI-T rekutengesa nekugadzirisa.
Pamusoro pemvumo yakapihwa nechidimbu ichi kana imwe vimbiso yeinishuwarenzi inoshanda, Uni-T haipe chero imwe vimbiso iri pachena kana inorehwa, kusanganisira asi isina kuganhurirwa kune kutengeswa kwechigadzirwa uye chinangwa chakakosha kune chero chinorehwa waranti. Chero zvazvingava, UNI-T yekurasika isina kunanga, yakakosha, kana yakakosha haina kutakura mutoro.

6.2 Bata Isu
Kana kushandiswa kwechigadzirwa ichi kwakonzera chero kusagadzikana, unogona kubata Uni-Trend Technology (China) Limited zvakananga ku mainland China:
Pakati pa8:30am kusvika 5:30pm nguva yeBeijing, Chishanu kusvika Muvhuro kana neemail pa: infosh@uni-trend.com.cn
Zvigadzirwa zvinobva kumatunhu ari kunze kweChina, ndapota taura nemutengesi wako weUNI-T kana nzvimbo yekutengesa.
Zvizhinji zvezvigadzirwa zvinotsigira UNI-T zvine yakawedzera waranti yenguva chirongwa uye nguva yekuenzanisa, ndapota taura nemutengesi wako weUNI-T kana nzvimbo yekutengesa.
Kuti uwane rondedzero yekero yenzvimbo dzedu dzesevhisi, ndapota shanya yedu website pa URL: http://www.uni-trend.com

Appendix A Factory Reset State

Parameters	Factory Defaults
Channel Parameters
Current Carrier Wave	Sine Wave
Output Outload	50Ω
Synchronous Output	Channel
Channel Output	Close
Channel Output Invert	Close
Amplitude Limit	Close
Amplitude Upper Limit	+5V
Amplitude Lower Limit	-5V
Sravana Sameeralu Serial 4th Basic Wave
Frequency	1kHz
Ampltide	100mVpp
DC Offset	0mV
Chekutanga Phase	0°
Duty Cyle yeSquare Wave	50%
Symmetryof Ramp Wave	100%
Duty Cycle yePulse Wave	50%
Kutungamira Kumucheto kwePulse Wave	24ns
Muswe Kumucheto wePulse Wave	24ns
Arbitrary Wave
Bulit-in Arbitrary Wave	AbsSine
AM Kusiyanisa
Modulation Source	Internal
Modulation Shape	Sine Wave
Kusiyanisa inzwi Kakawanda	100Hz
Kusiyanisa inzwi Kudzika	100%
FM Modulation
Modulation Source	Internal
Modulation Shape	Sine Wave

Kusiyanisa inzwi Kakawanda	100Hz
Fequency Offset	1kHz
PM Modulation
Modulation Source	Internal
Modulation Shape	Sine Wave
Modulation Phase Frequency	100Hz
Phase Offset	180°
PWM Modulation
Modulation Source	Internal
Modulation Shape	Pulse Wave
Kusiyanisa inzwi Kakawanda	100Hz
Duty Cycle Kutsauka	20%
Bvunza Modulation
Modulation Source	Internal
ASKRate	100Hz
FSK Kusiyanisa
Modulation Source	Internal
Mutakuri Wave Frequency	1kHz
Hop Frequency	2MHz
FSKRate	100Hz
PSK Modulation
Modulation Source	Internal
PSK Rate	100Hz
PSK Phase	180°
Tsvaira
Kutsvaira Type	Linear
Kutanga Frequency	1kHz
TerminalFrequency	2kHz
Kutsvaira Nguva	1s
Trigger Source	Internal

Parameters yeSystem
Inzwi reBuzzer	Vhura
Nhamba Format	，
Backlight	100%
Mutauro*	Yakatemwa neFactory Settings

Appendix B Technical Specifications

Type	UTG1020A	UTG1010A	UTG1005A
Channel	Single Channel
Max. Frequency	20MHz	10MHz	5MHz
Sample Rate	125MSa / s
Waveform	Sine Wave, Square Wave, Triangle Wave, Pulse Wave, Ramp Wave, Noise, DC, Arbitrary Waveform
Working Mode	Output Stobe, Nguva, Modulation, Scanning
Modulation Type	AM,FM,PM,ASK,FSK,PSK,PWM
Zvimiro zveWaveform
Sine Wave
Frequency Range	1μHz~20MHz	1μHz~10MHz	1μHz ~ 5MHz
Resolution	1μHz
Kururama	± 50ppm mumazuva makumi mapfumbamwe, ± 90ppm mugore rimwe (100 ° C ~ 18 ° C)
Harmonic Distortion Kukosha chaiko)	Muedzo Mamiriro: Kuburitsa simba 0dBm
	-55dBc
	-50dBc
	-40dBc
Yakazara Harmonic Distortion (Yakajairika Kukosha)	DC ~ 20kHz, 1Vpp＜0.2%
Square Wave
Frequency Range	1μHz ~ 5MHz
Resolution	1μHz
Kutungamira / Muswe Nguva	＜24ns (yakajairika kukosha, 1kHz, 1Vpp)
Overshoot (Typical Value)	＜2%
Duty Cycle	0.01%~99.99%
Min.Pulse	≥80ns
Jittering (Typical Value)	1ns + 100ppm yenguva
Ramp Wave

Frequency Range	1μHz~400kHz
Resolution	1μHz
Nonlinear Degree	1% ± 2 mV (yakajairika kukosha, 1kHz, 1Vpp, symmetry 50%)
Symmetry	0.0% kusvika 100.0%
Min. Edge Time	≥400ns
Pulse Wave
Frequency Range	1μHz ~ 5MHz
Resolution	1μHz
Pulse Eidth	≥80ns
Kutungamira / Muswe Nguva	＜24ns (yakajairika kukosha, 1kHz, 1Vpp)
Overshoot (Typical Value)	＜2%
Jittering (Typical Value)	1ns + 100ppm yenguva
DC Offset
Range (Peak Value AC+DC)	±5V(50Ω)
	± 10V (Kupikisa Kwepamusoro)
Offset Precision	± (\|1% yezvigadziriso zvekugadzirisa\|+0.5% ye ampmvura +2mV)
Zvimiro zveArbitrary Waveform
Frequency Range	1μHz ~ 3MHz	1μHz ~ 2MHz	1μHz ~ 1MHz
Resolution	1μHz
Waveform Length	2048 points
Vertical Resolution	14bits (kusanganisira zviratidzo)
Sample Rate	125MSa / s
Non-volatile Memory	16 mhando dze waveform
Output Features
Amplitude Range	1mVpp~10Vpp（50Ω,≤10MHz 1mVpp~5Vpp (50Ω,20MHz)	1mVpp~10Vpp (50Ω)
	2mVpp ~ 20Vpp (yakakwirira kuramba, ≤ 10MHz) 2mVpp ~ 10Vpp (yakakwirira kuramba, ≤20MHz)	2mVpp ~ 20Vpp (yakakwirira kuramba)
Kururama	1% ye ampLitude kuseta kukosha ± 2 mV

Amplitude Flatness (inoenderana nesine wave ye1kHz, 1Vpp/50Ω)	＜100kHz 0.1dB
	100kHz ~ 10MHz 0.2dB
Waveform Output
Impedance	Kukosha chaiko kwe50Ω
Insulation	Kunyika waya, max.42Vpk
Dziviriro	Short-circuit Protection
Modulation Type
AM Kusiyanisa
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modulation Shape	Sine Wave, Square Wave, Ramp Mafungu, Noise, Arbitrary Wave
Kusiyanisa inzwi Kakawanda	2mHz ~ 50kHz
Kusiyanisa inzwi Kudzika	0%~120%
FM Modulation
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modsulation Shape	Sine Wave, Square Wave, Ramp Mafungu, Noise, Arbitrary Wave
Kusiyanisa inzwi Kakawanda	2mHz ~ 50kHz
Frequency Offset	1μHz ~ 10MHz	1μHz ~ 5MHz	1μHz ~ 2.5MHz
PM Modulation
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modsulation Shape	Sine Wave, Square Wave, Ramp Mafungu, Noise, Arbitrary Wave
Kusiyanisa inzwi Kakawanda	2mHz ~ 50kHz
Phase Offset	0°~360°
Bvunza Modulation
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modulation Shape	Square Wave ye50% yebasa kutenderera
Kusiyanisa inzwi Kakawanda	2mHz ~ 100kHz

FSK Kusiyanisa
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modulation Shape	Square Wave ye50% yebasa kutenderera
Kusiyanisa inzwi Kakawanda	2mHz ~ 100kHz
PSK Modulation
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave, Arbitrary Wave
Source	Mukati/Ekunze
Modulation Shape	Square wave ye50% yebasa kutenderera
Kusiyanisa inzwi Kakawanda	2mHz ~ 100kHz
PWM Modulation
Mutakuri Wave	Pulse Wave
Source	Mukati/Ekunze
Modulation Shape	Sine Wave, Square Wave, Ramp Mafungu, Noise, Arbitrary Wave
Kusiyanisa inzwi Kakawanda	2mHz ~ 50kHz
Width Kutsauka	0% ~ 49.99% yehupamhi hwepulse
Tsvaira
Mutakuri Wave	Sine Wave, Square Wave, Ramp Wave
Type	Linearity, Logarithm
Kutsvaira Nguva	1ms~500s±0.1%
Trigger Source	Manual, Internal, External
Synchronous Signal
Output Level	TTL inoenderana
Output Frequency	1μHz~10MHz	1μHz~10MHz	1μHz ~ 5MHz
Output Resistance	50Ω, kukosha chaiko
Coupled Mode	Direct Current
Mberi Panel Chibatanidza
Modulation Input	± 5Vpk panguva yese yekuyera
	20kΩ yekupokana kwekuisa
Trigger Kuburitsa	TTL inoenderana

Appendix C Accessories List

Type	UTG1000A
Standard Accessories	Simba remagetsi rinosangana nenyika yemuno
	USB data tambo (UT-D06)
	BNC tambo (1 mita)
	Mushandisi CD
	Warranty card

Appendix D Kuchengetedza uye Kuchenesa

General Maintenance

Usachengete kana kuisa chiridzwa uye liquid crystal kuratidza muchiedza chezuva.
Kuti udzivise kukuvadza chiridzwa kana probe, usapfapfaize mhute, mvura kana solvent pachiridzwa kana probe.

Kuchenesa uye Kuchengetedza

Chenesa chiridzwa zvinoenderana nemamiriro ekushandisa.
Ndapota bvisa magetsi, uye ne damp asi usingadonhedze machira akapfava, pukuta chiridzwa chacho (chakakodzera kushandisa chigadziriso chakapfava kana mvura kupukuta guruva pachiridzwa, usashandise chemistry kana chekuchenesa chine zvinhu zvine simba zvakaita sebenzene, toluene, xylene, acetone, nezvimwewo) pukuta guruva kubva pamidziyo uye chiridzwa.
Paunenge uchichenesa iyo LCD skrini, ndapota teerera uye chengetedza iyo LCD skrini.
Usashandise chero makemikari abrasive ekuchenesa agent pane chiridzwa.
Yambiro: Ndapota simbisai kuti chiridzwa chacho chaoma zvachose chisati chashandiswa, kudzivirira kukanganisa uye kukuvara kwemunhu kunokonzerwa nemagetsi mapfupi emagetsi anokonzerwa nehunyoro.

Mugadziri:
Uni-Trend Technology (China) Limited
No 6, Gong Ye Bei ndiyo Mugwagwa
Songshan Lake National High-Tech Maindasitiri
Development Zone, Dongguan Guta
Guangdong Province
China
Posta! Kodhi:523 808
Headquarters:
Uni-Trend Group Limited
Rm901, 9/F, Nanyang Plaza
57 Hung To Road
Wun Tong
Kowloon, Hong Kong
Runhare: (852) 2950 9168
Fax: (852) 2950 9303
Email: info@uni-trend.com
http://Awww.uni-trend.com

Zvinyorwa / Zvishandiso

UNI-T UTG1000 Series Function Arbitrary Waveform Jenareta [pdf] User Manual
UTG1000 Series Function Arbitrary Waveform Generator, UTG1000 Series, Function Arbitrary Waveform Generator, Arbitrary Waveform Generator, Waveform Generator, Generator

References

User Manual

Nhanganyaya