ESPC6WROOM1 N16 Module Espressif System Mushandisi Manual

Install Prerequisites: Install the necessary software tools as per the requirements.
Tora ESP-IDF: Obtain the ESP-IDF (Espressif IoT Development Framework) for development.

Seta Zvishandiso: Configure the development tools required for programming.
Gadzirisa Environment Variables: Set up environment variables for the development environment.

Gadzira Yako Yekutanga Project
Follow these steps to create your first project with the ESP32-C6-WROOM-1 module:

Start a Project: Begin a new project in your development environment.

Batanidza Chishandiso Chako: Connect the ESP32-C6-WROOM-1 module to your development setup.
Gadzira: Configure the project settings and peripherals as needed.

Build the Project: Build the project to generate the firmware.
Flash onto the Device: Flash the firmware onto the ESP32-C6-WROOM-1 module.

Monitor Monitor the output and behavior of your project.

Module that supports 2.4 GHz Wi-Fi 6 (802.11 ax), Bluetooth® 5 (LE), Zigbee and Thread
(802.15.4)
Yakavakwa yakatenderedza ESP32-C6 yakatevedzana yeSoCs, 32-bit RISC-V single-core microprocessor
Flash inosvika ku16 MB
23 GPIOs, yakapfuma seti yemaperipheral
Pa-board PCB antenna

Module Overview

Features

CPU uye On-Chip Memory
- ESP32-C6 yakamisikidzwa, 32-bit RISC-V single-core microprocessor, inosvika 160 MHz
- ROM: 320 KB
- HP SRAM: 512 KB
- LP SRAM: 16 KB
Wi-Fi
- 1T1R mu2.4 GHz bhendi
- Kushanda frequency: 2412 ~ 2462 MHz
- IEEE 802.11ax-inoenderana
  - 20 MHz-chete isiri-AP modhi
  - MCS0 ~MCS9
  - Uplink uye downlink OFDMA, kunyanya yakakodzera yekubatanidza panguva imwe chete munzvimbo dzakakwirira-density
  - Downlink MU-MIMO (yakawanda-mushandisi, yakawanda yekuisa, yakawanda kuburitsa) kuwedzera network network
  - Beamformee inovandudza chiratidzo chemhando
  - Chiratidzo chemhando yechiteshi (CQI)
  - DCM (dual carrier modulation) kuvandudza kubatana kwakasimba
  - Kushandiswazve kweSpatial kuwedzera maparallel transmissions
  - Target yekumuka nguva (TWT) inogonesa nzira dzekuchengetedza simba
- Inonyatsoenderana neIEEE 802.11b/g/n protocol
  - 20 MHz uye 40 MHz bandwidth
  - Nhamba yedata inosvika ku150 Mbps
  - Wi-Fi Multimedia (WMM)
  - TX/RX A-MPDU, TX/RX A-MSDU
  - Pakarepo Block ACK
  - Kupatsanurwa uye defragmentation
  - Mukana wekutumira (TXOP)
  - Otomatiki Beacon yekutarisa (hardware TSF)
  - 4 × chaiyo Wi-Fi interfaces
  - Kutsigirwa panguva imwe chete yeInfrastructure BSS muStation mode, SoftAP mode, Station + SoftAP mode, uye unzenza
    Ziva kuti kana ESP32-C6 ichitarisa muStation modhi, iyo SoftAP chiteshi inochinja pamwe nechiteshi chiteshi.
  - 802.11mc FTM
Makaralı
- Bluetooth LE: Bluetooth 5.3 yakasimbiswa
- Bluetooth mesh
- High simba mode
- Speed: 1 Mbps, 2 Mbps
- Advertising extensions
- Maseti akawanda ekushambadzira
- Kusarudzwa kwechiteshi algorithm #2
- LE simba rekutonga
- Yemukati co-existence mechanic pakati peWi-Fi neBluetooth yekugovera antenna yakafanana
IEEE 802.15.4
- Inopindirana neIEEE 802.15.4-2015 protocol
- OQPSK PHY mu2.4 GHz bhendi
- Nhamba yedata: 250 Kbps
- Thread 1.3
- Zigbee 3.0
Peripherals
- GPIO, SPI, parallel IO interface, UART, I2C, I2S,RMT (TX/RX), pulse counter, LED PWM, USB Serial/JTAG controller, MCPWM, SDIO2.0 muranda controller, GDMA, TWAI® controller, on-chip debug functionality kuburikidza neJ.TAG, event task matrix,ADC, temperature sensor, general-purpose timers, watchdog timers, etc.
  Yakabatanidzwa Zvikamu paModule
- 40 MHz crystal oscillator
- SPI flash

Kanyanga Sarudzo
- Pa-board PCB antenna
Operating Conditions
- Kushanda voltage/Simba rekushandisa: 3.0 ~ 3.6 V
- Kushanda ambient tembiricha:
  - 85 °C shanduro module: -40 ~ 85 °C
  - 105 °C shanduro module: -40 ~ 105 °C

Tsanangudzo

ESP32-C6-WROOM-1 is a general-purpose Wi-Fi, IEEE 802.15.4, and Bluetooth LE module. The rich set of peripherals and high performance make the module an ideal choice for smart homes, industrial automation, health care, consumer electronics, etc.
ESP32-C6-WROOM-1 module features an external SPI flash.

The ordering information for ESP32-C6-WROOM-1 is as follows:

Tafura 1: ESP32-C6-WROOM-1 Ordering Information

Kuodha Code	Flash	Ambient Temp. (°C)	Size (mm)
ESP32-C6-WROOM-1-N4	4 MB (Quad SPI)	-40 ~ 85	18.0 × 25.5 × 3.1
ESP32-C6-WROOM-1-H4	4 MB (Quad SPI)	-40 ~ 105
ESP32-C6-WROOM-1-N8	8 MB (Quad SPI)	-40 ~ 85
ESP32-C6-WROOM-1-N16	16 MB (Quad SPI)	-40 ~ 85

Papakati peiyi module ndeye ESP32-C6, 32-bit RISC-V single-core processor.

ESP32-C6 integrates a rich set of peripherals including SPI, parallel IO interface, UART, I2C, I2S, RMT (TX/RX),LED PWM, USB Serial/JTAG controller, MCPWM, SDIO2.0 muranda controller, GDMA, TWAI® controller, on-chip debug functionality kuburikidza neJ.TAG, chiitiko chebasa matrix, pamwe nekusvika makumi maviri nemaviri GPIOs, nezvimwe.

Cherechedza:
For more information on ESP32-C6, please refer to ESP32-C6 Series Datasheet.

Pin Definitions

Kurongedzwa kwepini
Iyo pini dhayagiramu pazasi inoratidza inofungidzirwa nzvimbo yemapini pane module.

Pin Tsanangudzo
Iyo module ine 29 pini. Ona tsananguro dzepini muTable 2 Pin Definitions.
Nezve peripheral pini zvigadziriso, ndapota tarisa kune ESP32-C6 Series Datasheet.

Tafura 2: Pin Definitions

Zita	Aihwa.	Type¹	Function
GND	1	P	Ground
3V3	2	P	Magetsi
EN	3	I	High: on, inogonesa chip. Yakaderera: yadzimwa, iyo chip inodzima. Cherechedza: Usasiye pini yeEN ichiyangarara.
IO4	4	I/O/T	MTMS, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD
IO5	5	I/O/T	MTDI, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP
IO6	6	I/O/T	MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FSPICLK
IO7	7	I/O/T	MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID
IO0	8	I/O/T	GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0
IO1	9	I/O/T	GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1
IO8	10	I/O/T	GPIO8
IO10	11	I/O/T	GPIO10
IO11	12	I/O/T	GPIO11
IO12	13	I/O/T	GPIO12, USB_D-
IO13	14	I/O/T	GPIO13, USB_D+
IO9	15	I/O/T	GPIO9
IO18	16	I/O/T	GPIO18, SDIO_CMD, FSPICS2
IO19	17	I/O/T	GPIO19, SDIO_CLK, FSPICS3
IO20	18	I/O/T	GPIO20, SDIO_DATA0, FSPICS4
IO21	19	I/O/T	GPIO21, SDIO_DATA1, FSPICS5
IO22	20	I/O/T	GPIO22, SDIO_DATA2
IO23	21	I/O/T	GPIO23, SDIO_DATA3
NC	22	—	NC
IO15	23	I/O/T	GPIO15
RXD0	24	I/O/T	U0RXD, GPIO17, FSPICS1
TXD0	25	I/O/T	U0TXD, GPIO16, FSPICS0
IO3	26	I/O/T	GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3
IO2	27	I/O/T	GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ
GND	28	P	Ground
EPAD	29	P	Ground

1 P: power supply; I: input; O: output; T: high impedance.

Tanga

Zvaunoda
Kugadzira zvikumbiro zvemodule unoda:

1 x ESP32-C6-WROOM-1

1 x Espressif RF yekuongorora bhodhi
1 x USB-ku-Serial bhodhi
1 x Micro-USB tambo

1 x PC inoshandisa Linux

Mugwaro iri remushandisi, tinotora Linux inoshanda sisitimu seye example. Kuti uwane rumwe ruzivo nezve kumisikidzwa paWindows uye macOS, ndapota tarisa kune ESP-IDF Programming Guide.

Hardware Connection

Solder iyo ESP32-C6-WROOM-1 module kune iyo RF yekuyedza bhodhi sezvakaratidzwa mumufananidzo 2.
Batanidza iyo RF yekuyedza bhodhi kune USB-ku-Serial bhodhi kuburikidza neTXD, RXD, uye GND.
Batanidza USB-ku-Serial board kuPC.

Batanidza RF yekuyedza bhodhi kuPC kana dhiraivha yemagetsi kugonesa 5 V magetsi, kuburikidza neMicro-USB tambo.
Panguva yekurodha, batanidza IO9 kuGND kuburikidza nejumper. Wobva wabatidza "BATIA" bhodhi rekuyedza.
Dhawunirodha firmware muflash. Kuti uwane rumwe ruzivo, ona zvikamu pazasi.

Mushure mekurodha, bvisa jumper paIO9 uye GND.
Simba kumusoro kweRF yekuongorora bhodhi zvakare. Iyo module ichachinja kune inoshanda mode. Iyo chip ichaverenga zvirongwa kubva kuflash pakutanga.

Cherechedza:
IO9 ndeyemukati logic yakakwira. Kana IO9 yakagadzirirwa kudhonza-kumusoro, iyo Boot mode inosarudzwa. Kana pini iyi idhonzera pasi kana kuti yasara ichiyangarara, iyo
Download mode is selected. For more information on ESP32-C6-WROOM-1, please refer to ESP32-C6 Series Datasheet.

Gadzira Development Environment
Iyo Espressif IoT Development Framework (ESP-IDF kwenguva pfupi) igadziriro yekugadzira zvikumbiro zvichibva paEspressif ESP32. Vashandisi vanogona kugadzira maapplication neESP32-C6 muWindows/Linux/macOS zvichibva paESP-IDF. Pano isu tinotora Linux inoshanda sisitimu se example.

Isai Zvokutanga
Kuti uunganidze neESP-IDF unofanirwa kuwana mapakeji anotevera:
- CentOS 7 & 8:
- Ubuntu uye Debian:
- Arch:
  Cherechedza:
  - Gwaro iri rinoshandisa dhairekitori ~/esp paLinux senge yekuisa folda yeESP-IDF.
  - Ramba uchifunga kuti ESP-IDF haitsigire nzvimbo munzira.
Tora ESP-IDF
To build applications for ESP32-C6-WROOM-1 module, you need the software libraries provided by Espressif in ESP-IDF repository.
Kuti uwane ESP-IDF, gadzira dhairekitori rekuisa (~/esp) kurodha ESP-IDF kune uye kutevedzera repository ne 'git clone':
ESP-IDF ichatorwa mu ~/esp/esp-idf. Bvunza ESP-IDF Shanduro kune ruzivo rwekuti ndeipi ESP-IDF vhezheni yekushandisa mune yakapihwa mamiriro.
Gadzirisa Zvishandiso
Aside from the ESP-IDF, you also need to install the tools used by ESP-IDF, such as the compiler, debugger,Python packages, etc. ESP-IDF provides a script named ’install.sh’ to help set up the tools in one go.

Gadzirisa Environment Variables
Zvishandiso zvakaiswa hazvisati zvawedzerwa kune PATH nharaunda inosiyana. Kuita kuti maturusi ashandiswe kubva kumutsara wekuraira, mamwe mamiriro enzvimbo anofanirwa kusetwa. ESP-IDF inopa imwe script 'export.sh' inoita izvozvo. Mune iyo terminal yauchazoshandisa ESP-IDF, mhanya:

Iye zvino zvese zvagadzirira, unogona kuvaka yako yekutanga purojekiti paESP32-C6-WROOM-1 module.

Gadzira Yako Yekutanga Project

Kutanga chirongwa
Now you are ready to prepare your application for ESP32-C6-WROOM-1 module. You can start with tanga/hello_world chirongwa kubva examples directory muESP-IDF.
Kopa kutanga/hello_world ku ~/esp dhairekitori:Kune huwandu hwe example mapurojekiti mune yekareampLes directory muESP-IDF. Unogona kukopa chero purojekiti nenzira imwechete seyakaratidzwa pamusoro uye woimhanyisa. Zvinogoneka zvakare kugadzira examps in-place, pasina kutanga waakopa.
Unganidza Mudziyo Wako
Zvino batanidza module yako pakombuta uye tarisa pasi peiyo serial port iyo module inoonekwa. Serial ports muLinux anotanga ne '/ dev/tty' mumazita avo. Mhanya murairo uri pasi apa kaviri, kutanga nebhodhi risina kuvharwa, uye nekubatanidzwa. Chiteshi chinooneka kechipiri ndicho chaunoda:
Cherechedza:

Chengetedza zita rechiteshi riri nyore sezvauchazorida mumatanho anotevera.
Configure
Enda kune yako 'hello_world' dhairekitori kubva Danho 3.4.1. Tanga Project, isa ESP32-C6 chip sechinangwa uye mhanyisa purojekiti yekumisikidza utility 'menuconfig'.
Setting the target with ‘idf.py set-target ESP32-C6’ should be done once, after opening a new project. If the project contains some existing builds and configuration, they will be cleared and initialized. The target may be saved in environment variable to skip this step at all. See Kusarudza Chinangwa kuti uwane rumwe ruzivo.
Kana matanho apfuura akaitwa nemazvo, iyi inotevera menyu inobuda:
You are using this menu to set up project specific variables, e.g. Wi-Fi network name and password, the
processor speed, etc. Setting up the project with menuconfig may be skipped for “hello_word”. This example will
run with default configuration
The colors of the menu could be different in your terminal. You can change the appearance with the option ‘–style’. Please run ‘idf.py menuconfig –help’–for further information.

Vakai Project
Gadzira purojekiti nekumhanya:
This command will compile the application and all ESP-IDF components, then it will generate the bootloader,partition table, and application binaries.
Kana pasina zvikanganiso, kuvaka kuchapedza nekugadzira iyo firmware binary .bin file.
Flash paChishandiso
Ratidza mabhinari auchangobva kuvaka pane yako module nekumhanya:
Tsiva PORT neESP32-C6 board's serial port zita kubva Danho: Batanidza Chishandiso Chako.
Iwe unogona zvakare kushandura iyo flasher baud mwero nekutsiva BAUD neiyo baud rate yaunoda. The default baud rate ndeye 460800.
Kuti uwane rumwe ruzivo nezve idf.py nharo, ona idf.py.
Cherechedza:
Iyo sarudzo 'flash' inovaka uye inopenya purojekiti, saka kumhanya 'idf.py kuvaka' hakudiwi.
Paunenge uchipenya, iwe uchaona iyo inobuda log yakafanana neinotevera:
Kana pasina nyaya pakupera kweiyo flash process, bhodhi rinotangazve uye kutanga iyo "hello_world" application.
Monitor
Kuti utarise kana "hello_world" iri kushanda zvechokwadi, nyora 'idf.py -p PORT monitor' (Usakanganwa kutsiva PORT nezita rako rechiteshi).
Uyu murairo unotanga iyo IDF Monitor application:Mushure mekutanga uye yekuongorora matanda kukwira kumusoro, iwe unofanirwa kuona "Mhoro nyika!" yakadhindwa neapp.

Kubuda IDF yekutarisa shandisa nzira yekudimbudzira Ctrl+].
That’s all what you need to get started with ESP32-C6-WROOM-1 module! Now you are ready to try some other examples muESP-IDF, kana kuenda kurudyi kuvandudza yako maapplication.

Chirevo cheUS FCC

Chishandiso ichi chinoenderana neKDB 996369 D03 OEM Manual v01. Pazasi pane mirairo yekubatanidza yevagadziri vezvigadzirwa zvinoenderana neKDB 996369 D03 OEM Manual v01.

Rondedzero yeInoshanda FCC Mitemo
FCC Chikamu 15 Chikamu C 15.247

Specific Operational Use Conditions
Iyo module ine WiFi uye BLE mabasa.

Operation Frequency:
- WiFi: 2412 ~ 2462 MHz
- Bluetooth: 2402 ~ 2480 MHz
- Zigbee/Thread:2405 ~ 2480 MHz
Nhamba yeChannel:
- WiFi: 11
- Bluetooth: 40
- Zigbee/ Thread: 26

Modulation:
- WiFi: DSSS; OFDM
- Bluetooth: GFSK
- Zigbee/ Thread:O-QPSK
Rudzi: Pa-bhodhi PCB Antenna
- Kuwana: 3.26 dBi Max

Iyo module inogona kushandiswa kuIoT maapplication ane yakakura 3.26 dBi antenna. Mugadziri anoisa iyi moduli muchigadzirwa chavo anofanira kuona kuti chigadzirwa chekupedzisira checomposit chinoenderana nezvinodiwa neFCC nekuongorora kwehunyanzvi kana kuongororwa kumitemo yeFCC, kusanganisira iyo transmitter mashandiro. Mugadziri wemugadziri anofanirwa kuziva kusapa ruzivo kumushandisi wekupedzisira maererano nekuisa kana kubvisa iyi RF module mubhuku remushandisi wechigadzirwa chekupedzisira chinosanganisa module iyi. Gwaro rekushandisa rekupedzisira richasanganisira ruzivo rwese rwunodiwa / yambiro sekuratidzwa mubhuku rino.

Yakaganhurirwa Module Maitiro
Hazvigoneke. Iyo module imodule imwechete uye inoenderana nezvinodiwa zveFCC Chikamu 15.212.

Tevera Antenna Dhizaini
Hazvigoneke. Iyo module ine antenna yayo, uye haidi yakadhindwa bhodhi microstrip trace antenna, nezvimwe.

RF Exposure Mafungiro
Iyo module inofanirwa kuisirwa mumudziyo wekushandisa zvekuti ingangoita 20cm inochengetwa pakati peantenna nemuviri wevashandisi; uye kana RF yekuratidzwa chirevo kana magadzirirwo emodule akachinjwa, ipapo mugadziri wechigadzirwa anodiwa kuti atore mutoro wemodule kuburikidza neshanduko muFCC ID kana nyowani application. Iyo FCC ID yemodule haigone kushandiswa pachigadzirwa chekupedzisira. Mumamiriro ezvinhu aya, mugadziri anotambira achave nebasa rekuongororazve chigadzirwa chekupedzisira (kusanganisira chinotakurisa) uye kuwana mvumo yeFCC yakaparadzana.

Antennas

Tsanangudzo yeAntenna ndeiyi inotevera:

Rudzi: PCB Antenna

Kuwana: 3.26 dBi

Ichi chishandiso chinoitirwa chete kune vanogadzira vanogadzira pasi pezvinotevera mamiriro:

Iyo transmitter module inogona kunge isiri-inowanikwa nechero imwe transmitter kana antenna.
Iyo module ichashandiswa chete neyekunze antenna (s) iyo yakatanga kuedzwa uye yakasimbiswa neiyi module.
Iyo antenna inofanirwa kunge yakabatanidzwa zvachose kana kushandisa 'yakasarudzika' antenna coupler.

Chero bedzi mamiriro ari pamusoro asangana, imwe transmitter bvunzo haizodikanwa. Nekudaro, mugadziri wemugadziri achiri nebasa rekuyedza yavo yekupedzisira-chigadzirwa kune chero humwe hunodikanwa hwekuteerera hunodiwa neiyi module yakaiswa (ye ex.ample, dhijitari mudziyo kuburitsa, PC peripheral zvinodiwa, nezvimwewo).

Label uye Ruzivo rwekutevedza
Host product manufacturers need to provide a physical or e-label stating “Contains FCC ID: 2AC7Z-ESPC6WROOM1” with their finished product.

Ruzivo rwema test modes uye zvimwe zvinodiwa zvekuyedza

Operation Frequency:
- WiFi: 2412 ~ 2462 MHz
- Bluetooth: 2402 ~ 2480 MHz
- Zigbee/Thread: 2405~ 2480 MHz
Nhamba yeChannel:
- WiFi: 11
- Bluetooth: 40
- Zigbee/Thread:26
Modulation:
- WiFi: DSSS; OFDM
- Bluetooth: GFSK
- Zigbee/ Thread:O-QPSK

Mugadziri wemugadziri anofanirwa kuita bvunzo yeradiated uye yakaitwa emission uye yenhema emission, zvichingodaro, zvinoenderana neayo chaiwo modhi yekuyedza yeakamira-yega modular transmitter mune inotambira, pamwe neyeakawanda panguva imwe chete kufambisa mamodule kana mamwe ma transmit muchigadzirwa chinotambira. Chete kana zvese zviyedzo zvema test modes zvichitevedzera zvinodiwa neFCC, ipapo chigadzirwa chekupedzisira chinogona kutengeswa zviri pamutemo.

Kuwedzera kuyedzwa, Chikamu 15 Chikamu B chinoenderana
Iyo modular transmitter inongova FCC mvumo yeFCC Chikamu 15 Subpart C 15.247 uye kuti mugadziri wechigadzirwa ane basa rekuteedzera chero mimwe mitemo yeFCC inoshanda kune mugamuchiri asina kuvharwa nemodular transmitter mvumo yechitupa. Kana uyo anopihwa achitengesa chigadzirwa chavo seChikamu 15 Chikamu B chinoteerana (kana icho chinewo chisingafungidzirwe-radiator dijiti yedunhu), ipapo mubatsiri achapa chiziviso chekuti chigadzirwa chekupedzisira chekutambira chichiri kuda Chikamu 15 Chikamu B chekuyedza kutevedzera nemodular transmitter. yakaiswa.

Midziyo iyi yakaedzwa uye yakawanikwa inoenderana nemiganhu yeKirasi B yedhijitari mudziyo, zvichienderana neChikamu15 cheFCC Mitemo. Iyi miganho yakagadzirirwa kupa dziviriro inonzwisisika kubva mukukanganisa kunokuvadza mukuiswa kwekugara. Mudziyo uyu unogadzira, unoshandisa uye unogona kuvheneka redhiyo frequency simba uye, kana isina kuiswa uye kushandiswa zvinoenderana nemirairo, inogona kukonzera kukanganisa kunokanganisa kufambiswa kweredhiyo.

Nekudaro, hapana vimbiso yekuti kukanganisa hakuzoitika mune imwe yekumisikidza. Kana chishandiso ichi chikakonzera kukanganisa kunokuvadza kune redhiyo kana terevhizheni, iyo inogona kutariswa nekudzima mudziyo nekubatidza, mushandisi anokurudzirwa kuyedza kugadzirisa kukanganiswa neimwe yeanotevera matanho:

Reorrent kana kutamisa antenna inogamuchira.
Wedzera kupatsanurwa pakati pemidziyo nemugamuchiri.
Batanidza midziyo mune yekubuda padunhu rakasiyana neiyo iyo inotambirwa yakabatana.
Bvunza mutengesi kana nyanzvi yeredhiyo/TV ine ruzivo kuti ubatsirwe.

Ichi chishandiso chinoenderana neChikamu 15 cheFCC Mitemo. Kushanda kunoenderana nemamiriro maviri anotevera:

Ichi chishandiso chinogona kusakonzera kukanganisa kunokuvadza.
Muchina uyu unofanirwa kugamuchira chero kukanganisa kunowanikwa, kusanganisira kukanganisa kunogona kukonzera kushanda kwausingadi.

Yambiro:
Chero shanduko kana zvigadziriso zvisina kutenderwa nebato rine chekuita nekutevedzwa zvinogona kukanganisa mushandisi simba rekushandisa mudziyo.

Mudziyo uyu unoenderana neFCC RF radiation exposure limits yakatemerwa nharaunda isingadzoreki. Ichi chishandiso uye antenna yacho haifanire kunge iri-pamwe kana kushanda pamwe chete nechero imwe antenna kana transmitter. Antennas anoshandiswa kune iyi transmitter anofanirwa kuisirwa kuti ape chinhambwe chekuparadzanisa chingangoita makumi maviri masendimita kubva kuvanhu vese uye haafanirwe kunge ari pamwe chete kana kushanda akabatana nechero imwe antenna kana transmitter.

OEM Kubatanidzwa Mirayiridzo
Ichi chishandiso chinoitirwa chete kune vanosanganisa OEM pasi pemamiriro anotevera:

Iyo transmitter module inogona kunge isiri-inowanikwa nechero imwe transmitter kana antenna.
Iyo module ichashandiswa chete neyekunze antenna (s) iyo yakatanga kuedzwa uye yakasimbiswa neiyi module.

Chero bedzi mamiriro ari pamusoro asangana, imwe transmitter bvunzo haizodikanwa. Nekudaro, iyo yekubatanidza yeOEM ichiri nebasa rekuyedza yavo yekupedzisira-chigadzirwa kune chero yakawedzera kutevedza zvinodiwa zvinodiwa neiyi module yakaiswa (yeex.ample, dhijitari mudziyo kuburitsa, PC peripheral zvinodiwa, nezvimwewo).

Kutendeseka kwekushandisa iyo Module Certification
Muchiitiko chekuti aya mamiriro haagone kusangana (semuenzanisoampuye mamwe magadzirirwo elaptop kana kubatanidza nzvimbo neimwe transmitter), ipapo mvumo yeFCC yemodule iyi yakabatana nemidziyo yekutambira haichanzi ishande uye iyo FCC ID yemodule haigone kushandiswa pachigadzirwa chekupedzisira. Mumamiriro ezvinhu aya, musanganisi weOEM achaita basa rekuongororazve chigadzirwa chekupedzisira (kusanganisira chinotakurisa) uye kuwana mvumo yeFCC yakaparadzana.

End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2AC7Z-ESPC6WROOM1”.

Industry Canada Chirevo

Muchina uyu unoenderana neIndustry Canada's rezenisi-exempt RSSs. Kushanda kunoenderana nemamiriro maviri anotevera:

Ichi chishandiso chinogona kusakonzera kukanganisa; uye
Muchina uyu unofanirwa kugamuchira chero kukanganisa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingade kwemudziyo.

Radiation Exposure Statement
Ichi chishandiso chinoenderana neIC radiation radiation yekumisikidza yakatemerwa nharaunda isingadzorwe. Iyi midziyo inofanirwa kuiswa uye kuvhiyiwa nepadiki daro 20 cm pakati rediyeta nemuviri wako.

RSS-247 Chikamu 6.4 (5)
Mudziyo wacho unogona kuregedza kutapurirana kana pasina ruzivo rwekufambisa, kana kutadza kushanda. Ziva kuti izvi hazvina kuitirwa kurambidza kutapurirana kwekutonga kana kusaina ruzivo kana kushandiswa kwekudzokorora makodhi painodiwa nehunyanzvi.

Ichi chishandiso chinoitirwa chete kune vanosanganisa OEM pasi peanotevera mamiriro (Kushandisa module mudziyo):

Iyo antenna inofanirwa kuiswa zvekuti 20 cm inochengetwa pakati peantenna nevashandisi, uye
Iyo transmitter module inogona kunge isiri-inowanikwa nechero imwe transmitter kana antenna.

Chero bedzi 2 mamiriro ari pamusoro asangana, imwe transmitter bvunzo haizodikanwa. Nekudaro, iyo yekubatanidza yeOEM ichiri nebasa rekuyedza yavo yekupedzisira-chigadzirwa kune chero chekuwedzera chinodiwa chekuteerera chinodiwa neiyi module yakaiswa.

CHINOKOSHA CHINOKOSHA:
Muchiitiko chekuti aya mamiriro haagone kusangana (semuenzanisoampkune mamwe malaptop magadziriso kana kuisirwa neimwe transmitter), ipapo mvumo yeCanada haichanzi ishande uye iyo IC ID haigone kushandiswa pachigadzirwa chekupedzisira. Mumamiriro ezvinhu aya, musanganisi weOEM achaita basa rekuongororazve chigadzirwa chekupedzisira (kusanganisira chinotakurisa) uye kuwana mvumo yeCanada yakaparadzana.

End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 21098-ESPC6WROOM

End Product Labeling
Iyi transmitter module inotenderwa chete kushandiswa mumudziyo umo antenna inogona kuiswa zvekuti 20 cm inogona kuchengetedzwa pakati peantenna nevashandisi. Chigadzirwa chekupedzisira chinofanira kunyorwa munzvimbo inoonekwa neinotevera:

Mibvunzo Inowanzo bvunzwa

Q: What are the main features of the ESP32-C6-WROOM-1 module?
A: The ESP32-C6-WROOM-1 module offers Wi-Fi, IEEE 802.15.4, and Bluetooth LE connectivity, making it suitable for various applications like smart homes, industrial automation, health care, and consumer electronics.

Q: How many pins does the ESP32-C6-WROOM-1 module have?
A: The module has a total of 29 pins for various functions.
Refer to the pin definitions table for detailed information on each pin’s function.

Zvinyorwa / Zvishandiso

ESPRESSIF ESPC6WROOM1 N16 Module Espressif System [pdf] User Manual
2AC7Z-ESPC6WROOM1, 2AC7ZESPC6WROOM1, espc6wroom1, ESPC6WROOM1 N16 Module Espressif System, ESPC6WROOM1, N16 Module Espressif System, Espressif System, System

References

User Manual

Date	Version	Kusunungura zvinyorwa
2023-04-21	v1.0	Official release

ESPC6WROOM1 N16 Module Espressif System

Mirayiridzo Yekushandiswa Kwechigadzirwa