What are the settings in inches for the Craftsman T100 36-inch mower platform height selections?
Based on the Craftsman T100 Series Lawn Tractor manual, the mower deck can be adjusted to five different positions using the Deck Lift Lever…
Manuals+ Q&A
Craftsman questions & answers
Browse answered questions about Craftsman, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
How do I drain the fuel from the Craftsman 3100 PSI MAX Pressure Washer?
To drain the fuel from your Craftsman 3100 PSI MAX Pressure Washer, especially for storage of 30 days or longer, follow these steps: Turn…
Why is my Craftsman CMXC1220 garage door opener failing to close and occasionally failing to open, even though the remote and exterior keypad work?
Based on the manual for your Craftsman CMXC1220, if the door will not close but the remote and exterior keypad are working, the most…
What size throttle cable and kill switch wire do I need for my Craftsman 46cc backpack leaf blower?
Based on the manual for the CRAFTSMAN BP510 (CMXGAAMR51BP), which is a similar 51cc model, specific dimensions (length or gauge) for the throttle cable…
Why has my CRAFTSMAN CMCSS800C1 V20 trimmer stopped working after only two uses?
If your CRAFTSMAN CMCSS800C1 V20 Cordless Handheld Grass Trimmer has stopped working after only a few uses, please check the following troubleshooting steps based…
My Craftsman 675 Series Log Splitter (Model # 247.77640) manual does not specify whether the dipstick should be fully inserted or just to the first thread when checking the hydraulic oil level. Can you clarify this?
The provided manual for the Craftsman 675 Series Log Splitter (Model No. 247.77641) does not explicitly state whether the dipstick should be fully inserted…
Why does my garage door close and then immediately open again?
When a garage door closes and then immediately reverses to the open position, it is usually caused by one of two issues: the Close…
What amperage fuse does the CRAFTSMAN CMXPTXA1202 tire inflator use?
The manual for the CRAFTSMAN CMXPTXA1202 does not explicitly state the exact amperage rating for the fuse. However, it notes that an extra fuse…
How do I reset two Craftsman AssureLink Connectivity Internet Gateways (Model 1B7543-1) that have stopped allowing remote access?
To perform a full factory reset on your Craftsman AssureLink Internet Gateway (Model 1B7543-1 / 53999), follow these specific steps as a standard power…
I just bought a Craftsman T2200 42-inch riding mower. Is there an operational tutorial to explain the levers, pedals, and switches, specifically how to put the transmission in neutral?
Based on the documentation for the Craftsman 42-inch riding mower series (such as model 13AN77XSA93), here is a breakdown of the controls you are…
The throttle is wide open all the time after installing a new carburetor on my Craftsman 247.25587 lawn tractor. How do I fix this?
If your throttle remains wide open after installing a new carburetor on your Craftsman lawn tractor (Model 247.25587), it is likely due to an…
How do I reinstall the mower deck (bottom panel) on the Craftsman LTS 1500 lawn tractor?
To reinstall the mower deck (the panel underneath) on your Craftsman LTS 1500, follow these general steps based on the standard assembly for this…
How do I change the pressure unit from BAR to PSI on the CRAFTSMAN CMXPTXA1201 Portable Tire Inflator?
To change the pressure unit on your CRAFTSMAN CMXPTXA1201 Portable Tire Inflator, follow these steps: Power On: Press the Power button to turn the…
Why does my CRAFTSMAN V60 Mower (Model CMCMW260) keep cutting out during use?
Based on the CRAFTSMAN V60 Mower (Model CMCMW260) manual, there are several common reasons why the motor may stop while mowing. Since your mower…
How do I adjust the idle speed on my Craftsman push mower?
The Craftsman CMXGMAM series push mower manual does not provide specific steps for manually adjusting the idle speed, as these engines are typically factory-set.…
What is the standard engine compression for the Craftsman B2000 25cc 2-cycle leaf blower?
The instruction manual for the CRAFTSMAN B2000 (25cc 2-Cycle) does not list a specific PSI (pounds per square inch) value for engine compression. However,…
How do I remove the trimmer head on the CRAFTSMAN CMCST900D1 V20 WEEDWACKER?
To remove the trimmer head components (specifically the spool and spool cap) for the CRAFTSMAN CMCST900D1 V20 WEEDWACKER, follow these steps: Safety First: Remove…
Can the hub be removed on the CRAFTSMAN CMCST900D1 V20 WEEDWACKER?
Based on the manual for the CRAFTSMAN CMCST900D1 V20 WEEDWACKER, the spool housing (hub) can be accessed and its internal components removed for maintenance,…
How do I remove a piece of wire or debris from the shaft of my CRAFTSMAN CMCST900D1 V20 WEEDWACKER?
To remove a piece of wire, cord, or debris that has become entangled in the shaft or spool area of your CRAFTSMAN CMCST900D1 WEEDWACKER,…
Where is the fuse located on the CRAFTSMAN CMEPW1900 Electric Pressure Washer?
The CRAFTSMAN CMEPW1900 Electric Pressure Washer does not have a traditional user-replaceable internal fuse. Instead, it relies on a GFCI (Ground Fault Circuit Interrupter)…
How do I raise the deck or blade assembly on a Craftsman Zero-Turn Tractor?
To raise the blade assembly (cutting deck) on a Craftsman Zero-Turn Tractor, you must use the Deck Lift Lever located on the right-hand fender…
How do I replace the belt on a Craftsman Z6000 Series Zero-Turn Rider?
To replace the deck drive belt on your Craftsman Z6000 Series Zero-Turn Rider, follow these steps: 1. Remove the Mower Deck Move the tractor…
Where can I find replacement upper, lower, and concentrator tubes for the CRAFTSMAN CMEBL7000?
To obtain replacement tubes for your CRAFTSMAN CMEBL7000, you should contact CRAFTSMAN customer support or visit an authorized service center. According to the manual,…
How do I reassemble my Craftsman V20 Cordless 10-inch chainsaw?
To reassemble your Craftsman V20 Cordless chainsaw (Model CMCCS620), follow these steps for installing the guide bar and saw chain: Preparation: Ensure the battery…