TRU COMPONENTS TCN4S-24R Dual Display PID Temperature Controller Manual

Kutetezedwa kwa Phokoso: ± 2kV (pakati pa terminal yamagetsi ndi kulowetsa
Pokwerera)
Kusunga kukumbukira: Kukumbukira kosasunthika kumasungabe data ngakhale litakhala
mphamvu yazimitsa

Kutentha kwapakati: -10 mpaka 55°C (14 mpaka 131°F)
Chinyezi chozungulira: 25 mpaka 85% RH (osasunthika)

Malangizo Ogwiritsira Ntchito Zogulitsa

Zolinga Zachitetezo:

Chenjezo:

Ikani zida zosatetezeka mukamagwiritsa ntchito chipangizocho ndi makina
zomwe zingayambitse kuvulala kwakukulu kapena kutayika kwakukulu kwachuma.
Pewani kugwiritsa ntchito chipangizocho m'malo ndi
kuyaka / kuphulika / mpweya wowononga, chinyezi chambiri, kuwala kwa dzuwa,
kugwedezeka, mphamvu, kapena mchere.

Ikani nthawi zonse pagulu la chipangizo musanagwiritse ntchito.
Pewani kulumikiza, kukonza, kapena kuyang'ana chipangizocho pamene
cholumikizidwa ku gwero lamphamvu.
Yang'anani malumikizidwe musanayike mawaya.
Osasokoneza kapena kusintha unit.

Chenjezo:

Gwiritsani ntchito zingwe zoyenera kuti mulowetse mphamvu ndi kutulutsanso
kugwirizana pofuna kuteteza moto kapena kuwonongeka.
Gwiritsani ntchito chipangizocho mkati mwazomwe zidavotera.
Tsukani chipangizocho ndi nsalu youma yokha; pewani madzi kapena organic
zosungunulira.
Sungani mankhwala kutali ndi tchipisi tachitsulo, fumbi, ndi zotsalira za waya
kuteteza kuwonongeka.

Zochenjeza pakugwiritsa ntchito:

Onetsetsani kukhazikitsa koyenera ndi kulumikizana kwa unit monga momwe zilili
buku.
Nthawi zonse fufuzani ngati zizindikiro za kuwonongeka kapena kuvala pa zingwe ndi
zolumikizira.
Sungani malo aukhondo mozungulira gawolo kuti mupewe
kusokoneza.

Mafunso Ofunsidwa Kawirikawiri

Q: Kodi chowongolera kutenthachi chingagwiritsidwe ntchito ndi makina onse otentha ndi ozizira
- A: Inde, chowongolera kutenthachi chimathandizira kuwongolera kutentha ndi kuziziritsa.
Q: Ndi kutentha kotani komwe kumalimbikitsidwa kuti mugwire bwino ntchito?
- A: Kutentha koyenera kozungulira ndi -10 mpaka 55°C (14 mpaka 131°F).
Q: Kodi ndikukhazikitsanso bwanji chowongolera pamanja?
- A: Woyang'anira ali ndi njira yosinthira pamanja yomwe ingapezeke kudzera muzosankha zosintha. Onani bukhu lamalangizo kuti mumve zambiri pakukhazikitsanso pamanja.

Zambiri Zamalonda

Werengani ndikumvetsetsa buku la malangizo musanagwiritse ntchito mankhwalawa. Kuti mutetezeke, werengani ndikutsatira mfundo zachitetezo pansipa musanagwiritse ntchito. Kuti mutetezeke, werengani ndikutsatira zomwe zalembedwa mu bukhu la malangizo. Sungani buku la malangizo ili pamalo omwe mungapeze mosavuta. Mafotokozedwe, miyeso, ndi zina zotere zitha kusintha popanda chidziwitso pakuwongolera kwazinthu.

Zolinga Zachitetezo

Yang'anirani 'Zolinga Zachitetezo' kuti mugwire ntchito yotetezeka komanso yoyenera kupewa zoopsa.

chizindikiro chimasonyeza kusamala chifukwa cha zochitika zapadera zomwe zoopsa zikhoza kuchitika.

Chenjezo Kulephera kutsatira malangizo kungayambitse kuvulala koopsa kapena imfa

Chipangizo chosatetezedwa chiyenera kuikidwa mukamagwiritsa ntchito makina omwe angayambitse kuvulala kwambiri kapena kuwononga chuma chambiri. zipangizo, ndi zina zotero) Kulephera kutsatira malangizowa kungachititse munthu kuvulala, kutaya chuma kapena moto.

Osagwiritsa ntchito chipangizo pamalo pomwe mpweya woyaka, kuphulika/kuwononga, chinyezi chambiri, kuwala kwa dzuwa, kutentha kowala, kugwedezeka, mphamvu kapena mchere. Kulephera kutsatira malangizowa kungayambitse kuphulika kapena moto.
Kukhazikitsa pa chipangizo gulu ntchito. Kulephera kutsatira malangizowa kungayambitse moto kapena kugwedezeka kwamagetsi.
Osalumikiza, kukonza, kapena kuyang'ana chipangizocho mutalumikizidwa kugwero lamagetsi. Kulephera kutsatira malangizowa kungayambitse moto kapena kugwedezeka kwamagetsi.

Chongani 'Malumikizidwe' pamaso mawaya. Kulephera kutsatira malangizowa kungayambitse moto.
Osasokoneza kapena kusintha unit.

Kulephera kutsatira malangizowa kungayambitse moto kapena kugwedezeka kwamagetsi.

Chenjezo Kulephera kutsatira malangizo kungayambitse kuvulala kapena kuwonongeka kwazinthu

Mukalumikiza cholowetsa mphamvu ndi kutulutsa kwa relay, gwiritsani ntchito chingwe cha AWG 20 (0.50 mm2 ) kapena kupitilira apo, ndikumangitsa wononga ononga ndi torque yothina ya 0.74 mpaka 0.90 N m. Mukalumikiza chingwe cha sensa ndi kulumikizana popanda chingwe chodzipatulira, gwiritsani ntchito chingwe cha AWG 28 mpaka 16 ndikumangitsa wononga wononga ndi torque yothina ya 0.74 mpaka 0.90 N m Kulephera kutsatira malangizowa kungayambitse moto kapena kusagwira bwino ntchito chifukwa cholephera kulumikizana.
Gwiritsani ntchito unit mkati mwazomwe zidavotera. Kukanika kutsatira malangizowa kungawononge moto kapena zinthu

Gwiritsani ntchito nsalu youma kuti muyeretse chipangizocho, ndipo musagwiritse ntchito madzi kapena zosungunulira za organic. Kukanika kutsatira malangizowa kungayambitse moto kapena kugwedezeka kwamagetsi.
Sungani mankhwala kutali ndi chitsulo chip, fumbi, ndi zotsalira za waya zomwe zimalowa mu unit. Kukanika kutsatira malangizowa kungawononge moto kapena zinthu.

Chenjezo pa Kugwiritsa Ntchito

Tsatirani malangizo mu 'Kuchenjeza Panthawi Yogwiritsa Ntchito'. Apo ayi, zingayambitse ngozi zosayembekezereka.
Yang'anani polarity ya ma terminals musanayike mawaya sensa ya kutentha.
Pa sensa ya kutentha kwa RTD, imbani mawaya ngati 3-waya, pogwiritsa ntchito zingwe mu makulidwe ndi kutalika komweko. Pa sensa ya kutentha kwa thermocouple (TC), gwiritsani ntchito waya wolipiridwa powonjezera waya.

Khalani kutali ndi kuchuluka kwamphamvutagma e kapena zingwe zamagetsi kuti mupewe phokoso lolowera. Mukayika chingwe chamagetsi ndi mzere wa siginecha pafupi, gwiritsani ntchito fyuluta ya mzere kapena varistor pa chingwe chamagetsi ndi waya wotetezedwa pamzere wa siginecha. Osagwiritsa ntchito pafupi ndi zida zomwe zimapanga mphamvu yamphamvu ya maginito kapena phokoso lokwera kwambiri.
Ikani chosinthira magetsi kapena chophwanyira dera pamalo opezeka mosavuta kuti mupereke kapena kudutsira magetsi.
Osagwiritsa ntchito chipangizochi pazifukwa zina (monga voltmeter, ammeter), koma chowongolera kutentha.

Mukasintha sensor yolowera, zimitsani mphamvuyo kaye musanayisinthe. Pambuyo posintha sensa yolowera, sinthani mtengo wa parameter yofananira.
Pangani malo ofunikira mozungulira chipangizocho kuti mutenthe kutentha. Kuti muyeze bwino kutentha, tenthetsani chipangizocho kupitirira mphindi 20 mutayatsa magetsi.
Onetsetsani kuti voltagikufika ku voliyumu yovoteratage mkati mwa 2 sec pambuyo popereka mphamvu.

Osalumikiza ma terminals omwe sagwiritsidwa ntchito.
Chigawochi chingagwiritsidwe ntchito m'madera otsatirawa.
- M'nyumba (m'malo okhala adavotera 'Zofotokozera')
- Altitude Max. 2,000 m
- Digiri yowononga 2
- Kuyika gulu II

Zida Zopangira

Chogulitsa (+ bulaketi)
Buku la malangizo

Zofotokozera

Mtundu Wolowetsa ndi Kugwiritsa Ntchito Range

Kuyika kwa magawo ena kumakhala kochepa mukamagwiritsa ntchito chiwonetsero cha decimal.

Onetsani kulondola

Kufotokozera Magawo

Chiwonetsero cha PV (chofiira)
- RUN mode: Imawonetsa PV (mtengo wapano)
- Kukhazikitsa: Kuwonetsa dzina la parameter
SV Onetsani gawo (lobiriwira)
- RUN mode: Ikuwonetsa SV (Kuyika mtengo)
- Zokhazikitsira: Kuwonetsa mtengo wokhazikitsa parameter

Chizindikiro

Lowetsani kiyi

Zolakwa

Samalani kuti pakakhala cholakwika cha HHHH/ LLLL, zowongolera zitha kuchitika pozindikira kuchuluka kapena kuchepera kutengera mtundu wowongolera.

Makulidwe

Bulaketi

Njira Yoyikira

Mukayika chinthucho pagulu lokhala ndi bulaketi, ikani chipangizocho mu gulu, sungani bulaketiyo pokankha ndi screwdriver ya flathead.

Kulumikizana

Zolemba za Crimp Terminal

Unit: mm, gwiritsani ntchito crimp terminal ya mawonekedwe otsatirawa.

Kukhazikitsa Mode

Kukhazikitsanso Parameter

Dinani [◄] + [▲] + [▼] makiyi kupitirira 5 sec. mu Run mode, INIT imayatsa.

Sinthani mtengo wokhazikitsira ngati YES pokanikiza [▲], [▼] makiyi.
Dinani batani la [MODE] kuti mukhazikitsenso ma parameter onse kukhala okhazikika ndikubwerera kumayendedwe.

Kukhazikitsa kwa Parameter

Ma parameter ena amayatsidwa/azimitsidwa kutengera mtundu kapena mawonekedwe a magawo ena. Onani kufotokozera kwa chinthu chilichonse.
Zochunira m'mabala ndi zogwiritsira ntchito mawonedwe a decimal muzowonjezera.
Ngati palibe kiyi yolowera kwa masekondi opitilira 30 pagawo lililonse, imabwerera ku RUN mode.

Mukakanikiza fungulo la [MODE] mkati mwa 1 sekondi mutabwerera ku machitidwe opangira ntchito kuchokera ku gulu la parameter, lidzalowa mu gulu la parameter musanabwerere.
[MODE] kiyi: Imasunga mtengo wokhazikitsira wapano ndikusunthira kugawo lotsatira.
[◄] kiyi: Imayang'ana chinthu chokhazikika / Kusuntha mzere mukusintha mtengo
[▲], [▼] makiyi: Amasankha parameter / Kusintha mtengo
Kutsatizana kovomerezeka kwa magawo: Gulu la Parameter 2 → Gulu 1 Gulu → Kuyika kwa SV

Kutaya

Izi zimawonekera pazida zilizonse zamagetsi ndi zamagetsi zomwe zimayikidwa pamsika wa EU. Chizindikirochi chikuwonetsa kuti chipangizochi sichiyenera kutayidwa ngati zinyalala zamatauni zomwe sizinasankhidwe kumapeto kwa moyo wake.
Eni ake a WEEE (Zinyalala Zochokera ku Zida Zamagetsi ndi Zamagetsi) azitaya padera ndi zinyalala za tauni zomwe sizinasankhidwe. Mabatire ogwiritsidwa ntchito ndi ma accumulators, omwe sanatsekedwe ndi WEEE, komanso lamps zomwe zingathe kuchotsedwa ku WEEE m'njira yosawononga, ziyenera kuchotsedwa ndi ogwiritsa ntchito kumapeto kwa WEEE m'njira yosawononga isanaperekedwe kumalo osonkhanitsira.
Ogawa zida zamagetsi ndi zamagetsi amakakamizika mwalamulo kuti aperekenso zinyalala zaulere. Conrad imapereka njira zotsatirazi zobwerera kwaulere (zambiri zathu webtsamba):

m'maofesi athu a Conrad

pa malo osonkhanitsira a Conrad
pamalo osonkhanitsira a oyang'anira zinyalala za anthu kapena malo osonkhanitsira omwe amakhazikitsidwa ndi opanga kapena ogulitsa mkati mwa tanthauzo la ElektroG

Ogwiritsa ntchito mapeto ali ndi udindo wochotsa deta yanu kuchokera ku WEEE kuti iwonongeke. Zindikirani kuti maudindo osiyanasiyana okhudza kubweza kapena kukonzanso kwa WEEE atha kugwira ntchito m'maiko akunja kwa Germany.

Parameter 1 gulu

Parameter 2 gulu

Ma parameters omwe ali pansipa amayambika pamene mtengo wokhazikika wasinthidwa.
- Gulu la Parameter 1: AL1/2 alamu kutentha
- Gulu la Parameter 2: Kuwongolera zolowetsa, malire a SV apamwamba / otsika, alamu yotulutsa hysteresis, nthawi ya LBA, gulu la LBA
- SV mode yokhazikitsira: SV
Ngati SV ili yotsika kuposa malire otsika kapena apamwamba kuposa malire apamwamba pamene mtengo wasinthidwa, SV imasinthidwa kukhala mtengo wotsika / wapamwamba. Ngati 2-1 zolembera zasinthidwa, mtengo umasinthidwa kukhala Min./Max. mtengo wa Input specification.
Mtengo ukasinthidwa, mtengo wa 2-20 Sensor error MV umayambitsidwa kukhala 0.0 (OFF).

Mukasintha mtengo kuchokera ku PID kupita ku ONOF, mtengo uliwonse pazigawo zotsatirazi umasinthidwa. 2-19 Kiyi yolowetsamo pakompyuta: WOZIMUTSA, 2-20 Zolakwika za Sensor MV: 0.0 (pamene kuyika mtengo ndi wotsika kuposa 100.0)

Izi ndi zofalitsidwa ndi Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). Ufulu wonse kuphatikiza kumasulira ndi wosungidwa. Kujambulanso ndi njira iliyonse, mwachitsanzo fotokopi, filimu yaying'ono, kapena kujambula mu makina opangira deta kumafuna kuvomereza kolembedwa ndi mkonzi. Kusindikizanso, nawonso mbali ina, ndikoletsedwa. Bukuli likuyimira luso laukadaulo panthawi yosindikiza. Copyright 2024 ndi Conrad Electronic SE. *BN3016146 TCN_EN_TCD210225AB_20240417_INST_W

Zolemba / Zothandizira

TRU COMPONENTS TCN4S-24R Dual Display PID Temperature Controllers [pdf] Buku la Malangizo
TCN4S-24R Dual Display PID Temperature Controllers, TCN4S-24R, Dual Display PID Temperature Controllers, Display PID Temperature Controllers, PID Temperature Controllers, Temperature Controllers, Controllers

Maumboni

Buku Logwiritsa Ntchito

TRU COMPONENTS TCN4S-24R Dual Display PID Temperature Controllers