SmartGen HMC4000RM Remote Monitoring Controller Manual
Maumwini onse ndi otetezedwa. Palibe gawo lililonse la bukhuli lomwe lingasindikizidwenso mwanjira ina iliyonse (kuphatikiza kukopera kapena kusunga mu njira yamagetsi kapena china chilichonse) popanda chilolezo cholembedwa ndi mwiniwakeyo.
SmartGen ili ndi ufulu wosintha zomwe zili mu chikalatachi popanda kuzindikira.
Table 1 Software Version
| Tsiku | Baibulo | Zamkatimu |
| 2017-08-29 | 1.0 | Kutulutsidwa koyambirira |
| 2018-05-19 | 1.1 | Sinthani miyeso yoyikapo. |
| 2021-04-01 | 1.2 | Sinthani "A-phase power factor" yofotokozedwa mu 4th Screen of Screen Display kukhala "C-phase power factor". |
| 2023-12-05 | 1.3 | Kusintha lamp mafotokozedwe a mayeso; Onjezani zomwe zili ndi magawo a magawo a parameter. |
ZATHAVIEW
HMC4000RM Woyang'anira akutali amaphatikiza ukadaulo wa digito, ukadaulo wapadziko lonse lapansi komanso ukadaulo wapaintaneti womwe umagwiritsidwa ntchito pakuwunika kwakutali kwa unit imodzi kuti akwaniritse ntchito zakutali. Imagwirizana ndi chiwonetsero cha LCD, komanso mawonekedwe osankha achi China / Chingerezi. Ndi yodalirika komanso yosavuta kugwiritsa ntchito.
NTCHITO NDI MAKHALIDWE
Zomwe zili zazikulu ndi izi:
- 132 * 64 LCD yokhala ndi backbit, chiwonetsero cha mawonekedwe achi China/Chingerezi, ndi ntchito ya batani;
- Zipangizo za acrylic zolimba zolimba zakhala zikugwiritsidwa ntchito kuteteza chophimba chokhala ndi ntchito zazikulu zokana kuvala komanso zokana kukanda;
- Mabatani a silicone ndi mabatani omwe ali ndi ntchito yabwino kuti azigwira ntchito m'malo otentha kwambiri / otsika;
- Lumikizani kwa woyang'anira wolandila kudzera pa doko la RS485 kuti mukwaniritse kuwongolera kwakutali / kuyimitsa mumayendedwe akutali;
- Ndi LCD brilliance level (5 level) batani losinthira, ndilosavuta kugwiritsa ntchito nthawi zosiyanasiyana;
- Mulingo wachitetezo wopanda madzi IP65 chifukwa cha chisindikizo cha rabara chomwe chimayikidwa pakati pa mpanda wowongolera ndi fascia yamapaneli.
- Zida zopangira zitsulo zimagwiritsidwa ntchito;
- Mapangidwe amtundu, kuzimitsa pulasitiki ya ABS mpanda ndi njira yoyikapo yoyika; kakulidwe kakang'ono komanso kamangidwe kakang'ono ndikuyika kosavuta.
KULAMBIRA
Table 2 Technical Parameters
| Zinthu | Zamkatimu |
| Ntchito Voltage | DC8.0V mpaka DC35.0V, magetsi osasokoneza. |
| Kugwiritsa Ntchito Mphamvu | <2W |
| RS485 Kuyankhulana kwa Baud Rate | 2400bps/4800bps/9600bps/19200bps/38400bps akhoza kukhazikitsidwa |
| Case Dimension | 135mm x 110mm x 44mm |
| Kudula kwa Panel | 116mm x 90mm |
| Kutentha kwa Ntchito | (-25 ~ +70) ºC |
| Chinyezi Chogwira Ntchito | (20-93)% RH |
| Kutentha Kosungirako | (-25 ~ +70) ºC |
| Mlingo wa Chitetezo | Front panel IP65 |
| Insulation Intensity | Ikani AC2.2kV voltage pakati pa voltage terminal ndi low voltage terminal; Kutayikira kwapano sikupitilira 3mA mkati mwa 1min. |
| Kulemera | 0.22kg |
NTCHITO
Table 3 Kankhani mabatani Kufotokozera
| Zithunzi | Ntchito | Kufotokozera |
 |
Imani | Lekani kuyendetsa jenereta mumalowedwe akutali; Pamene jenereta yakhazikitsa ili kupuma, kukanikiza ndi kugwira batani kwa masekondi a 3 kudzayesa magetsi owonetsera (lamp mayeso); |
 |
Yambani | Mumawonekedwe akutali, dinani batani ili liyamba kukhazikitsa jenereta. |
 |
Dimmer + | Dinani batani ili kuti muwonjezere kuwala kwa LCD. |
 |
Dimmer - | Dinani batani ili kuti muchepetse kuwala kwa LCD. |
 |
Lamp Yesani | Mukakanikiza batani ili, LCD yowonetsedwa ndi zakuda ndipo ma LED onse omwe ali kutsogolo amawunikiridwa. Gwirani ndikudina batani ili kuti muchotse zidziwitso za alamu za oyang'anira kwanuko. |
 |
Khazikitsani/Tsimikizirani | Ntchito ndi standby. |
 |
Pamwamba/Onjezani | Dinani batani ili kuti musunthe skrini. |
 |
Pansi/Kuchepa | Dinani batani ili kuti musunthe skrini pansi. |
KUONETSA MASKANI
Table 4 Screen Display
| 1 Screen | Kufotokozera |
| Jenereta imagwiritsa ntchito chiwonetsero chazithunzi | |
 |
Kuthamanga kwa injini, generator-set UA/UAB voltage |
| Kuthamanga kwamafuta, Mphamvu yonyamula | |
| Udindo wa injini | |
| Jenereta ili pachiwonetsero chopumula | |
 |
Liwiro la injini, kutentha kwa madzi |
| Kuthamanga kwa mafuta, mphamvu yamagetsi voltage | |
| Udindo wa injini | |
| 2nd Screen | Kufotokozera |
 |
Kutentha kwamadzi kwa injini, magetsi owongolera |
| Kutentha kwamafuta a injini, charger voltage | |
| Nthawi yonse yoyendetsa injini | |
| Kuyesa kuyambitsa injini, mawonekedwe owongolera pano | |
| 3rd Screen | Kufotokozera |
 |
Waya voltage: Uab, Ubc, Uca |
| Gawo voltage: uwu, uwu | |
| Katundu panopa: IA, IB, IC | |
| Katundu yogwira mphamvu, katundu zotakasika mphamvu | |
| Mphamvu, pafupipafupi | |
| 4 Screen | Kufotokozera |
 |
Mphamvu yogwira ntchito, mphamvu yogwira ntchito, chiwonetsero champhamvu chowonekera |
| A-phase kW, A-phase kvar, A-phase kvA | |
| B-gawo kW, B-gawo kvar, B-gawo kvA | |
| C-gawo kW, C-gawo kvar, C-gawo kvA | |
| A-gawo mphamvu factor, C-gawo mphamvu factor, C-gawo mphamvu factor | |
| 5 Screen | Kufotokozera |
 |
Anasonkhanitsa yogwira mphamvu yamagetsi |
| Anasonkhanitsa zotakasika magetsi mphamvu | |
| 6 Screen | Kufotokozera |
 |
Lowetsani dzina ladoko |
| Lowetsani doko | |
| Dzina ladoko lotulutsa | |
| Zotuluka padoko | |
| dongosolo nthawi ino | |
| 7 Screen | Kufotokozera |
 |
Mtundu wa alamu |
| Dzina la alamu | |
Zindikirani: ngati palibe mawonekedwe amagetsi, chophimba cha 3, 4, ndi 5 chidzatetezedwa chokha.
WOLAMULIRA PANEL NDI NTCHITO
ULAMULIRO PANENE
Chithunzi cha 1 HMC4000RM Front Panel
ZINDIKIRANI: Gawo lachiwonetsero cha magetsi owonetsera:
Zizindikiro za Alamu: kung'anima pang'onopang'ono pamene machenjezo amachenjeza; kung'anima kwachangu pamene ma alarm otseka achitika; kuwala kuzimitsa pamene palibe ma alarm.
Zizindikiro: Kuwala kumazimitsa pamene gen set ili pafupi; kung'anima kamodzi pa sekondi poyambitsa kapena kutseka; nthawi zonse kumathamanga mwachizolowezi.
KUYAMBIRA KWAM'MBUYO/ISIMANI NTCHITO
CHITSANZO
Press 
ya woyang'anira gulu HMC4000 kuti alowe mumayendedwe akutali, mutatha kuwongolera kutali, ogwiritsa ntchito amatha kuwongolera patali HMC4000RM kuyamba/kuyimitsa ntchito.
KUKHALA KWAMBIRI KWAMBIRI
- Pamene lamulo loyambira kutali likugwira ntchito, "Start Delay" timer imayambitsidwa;
- "Yambani Kuchedwa" kuwerengera kudzawonetsedwa pa LCD;
- Kuchedwerako kukatha, kupatsa mphamvu kwa preheat relay (ngati kukonzedwa), chidziwitso cha "preheat kuchedwa XX s" chidzawonetsedwa pa LCD;
- Pambuyo pochedwa pamwambapa, Fuel Relay imapatsidwa mphamvu, kenako sekondi imodzi pambuyo pake, Start Relay ikuchita. Genset imadulidwa kwa nthawi yoikidwiratu. Ngati genset ilephera kuyatsa panthawi yoyeserera iyi, ndiye kuti kutumizirana mafuta ndikuyamba kutumizirana zinthu kumachotsedwa kwa nthawi yopumula yokhazikitsidwa kale; "Nthawi yopumula" imayamba ndikudikirira kuyesa kotsatira.
- Ngati kutsatizana koyambiraku kupitilira kupitilira kuchuluka kwa zoyeserera, kutsata koyambira kudzathetsedwa, ndipo Kulephera Kuyambitsa alamu kudzawonetsedwa patsamba la alamu la LCD.
- Mukayesa kuchita bwino, chowerengera cha "Safety On" chimayatsidwa. Kuchedwa kumeneku kukangotha, kuchedwa kwa "kuyamba osagwira ntchito" kumayambika (ngati kukonzedwa).
- Pambuyo poyambira osagwira ntchito, wowongolera amalowa mu liwiro la "Kuchenjeza" kuchedwa (ngati kukonzedwa).
- Pambuyo pa kuchedwa kwa "Kuchenjeza" kutha, jenereta idzalowa mu Normal Running status molunjika.
KUSINTHA KWA Akutali
- Kuyimitsa kwakutali kukagwira ntchito, wowongolera amayamba kuchedwa kwa "Kuzizira" (ngati kukonzedwa).
- Kuchedwa kwa "Kuzizira" kumeneku kukatha, "Stop Idle" imayambika. Pakuchedwa kwa "Stop Idle" (ngati kukonzedwa), kusagwira ntchito kumakhala ndi mphamvu.
- "Stop Idle" iyi ikatha, "ETS Solenoid Hold" imayamba, ndipo ngati kuyimitsa kwathunthu kudzaweruzidwa zokha. Kupatsirana kwa ETS kumakhala ndi mphamvu pomwe kutumizirana kwamafuta kumachotsedwa.
- "ETS Solenoid Hold" ikatha, "Dikirani Kuyimitsa Kuchedwa" imayamba. Kuyimitsa kwathunthu kumangodziwikiratu.
- Jenereta imayikidwa mumayendedwe ake oyimilira pambuyo poyimitsidwa. Kupanda kutero, kulephera kuyimitsa alamu kumayambitsidwa ndipo chidziwitso chofananira cha alamu chimawonetsedwa pa LCD (Ngati jenereta yayimitsidwa bwino pambuyo poti "kulephera kuyimitsa" alamu yayambika, injini idzalowa mu standby)
KULUMIKIZANA KWA WIRING
HMC4000RM wowongolera gulu lakumbuyo:
Fig.2 Controller Back Panel
Table 5 Kufotokozera kwa Terminal Connection
| Ayi. | Ntchito | Kukula kwa Chingwe | Ndemanga |
| 1 | B- | 2.5mm2 | Olumikizidwa ndi negative ya magetsi. |
| 2 | B+ | 2.5mm2 | Zolumikizidwa ndi zabwino zamagetsi. |
| 3 | NC | Osagwiritsidwa ntchito | |
| 4 | KODI H | 0.5mm2 | Doko ili ndikukulitsa mawonekedwe owunikira ndikusungidwa kwakanthawi.Chingwe chotchinga ndichovomerezeka ngati chikugwiritsidwa ntchito. |
| 5 | KODI L | 0.5mm2 | |
| 6 | CAN Common Ground | 0.5mm2 | |
| 7 | RS485 Common Ground | / | Waya wotchinga wa Impedance-120Ω amalimbikitsidwa, wokhala ndi malekezero ake amodzi. Mawonekedwewa amagwiritsidwa ntchito kulumikiza ndi woyang'anira gulu HMC4000. |
| 8 | RS485+ | 0.5mm2 | |
| 9 | Mtengo wa RS485- | 0.5mm2 |
ZINDIKIRANI: Doko la USB kumbuyo ndikukweza doko.
ZOTHANDIZA NDI MATANTHAUZO A ZINTHU ZOPHUNZITSIDWA
Table 6 Zamkatimu ndi Magawo a Parameter Setting
| Ayi. | Kanthu | Mtundu | Zosasintha | Kufotokozera |
| Kusintha kwa Module | ||||
| 1 | Mtengo wa RS485 | (0-4) | 2 | 0: 9600bps 1: 2400bps2: 4800bps 3: 19200bps 4: 38400bps |
| 2 | Imani Pang'ono | (0-1) | 0 | 0:2 gawo 1:1 Bit |
NTCHITO YOTHANDIZA
Chithunzi cha 3 HMC4000RM Choyimira Chogwiritsa Ntchito
KUYANG'ANIRA
KUKONZA MA Clip
- Controller ndi mapangidwe opangidwa ndi gulu; imakonzedwa ndi tatifupi pamene anaika.
- Chotsani chowongolera chowongolera (tembenuzani kutsata koloko) mpaka chifike pamalo oyenera.
- Kokani kopanira kumbuyo (kumbuyo kwa gawoli) kuwonetsetsa kuti magawo awiri ali mkati mwa mipata yawo.
- Tembenuzani zomangira zomata mozungulira mozungulira mpaka zitakhazikika pagulu.
ZINDIKIRANI: Chisamaliro chiyenera kutengedwa kuti musamangitse zomangira zomangirira.
ZONSE ZONSE NDI KUKHALA
Fig.4 Miyeso ya Mlandu ndi Kudula Gulu
KUSAKA ZOLAKWIKA
Table 7 Kuthetsa Mavuto
| Vuto | Njira Yotheka |
| Wowongolera samayankha ndi mphamvu. | Onani mabatire oyambira; Chongani chowongolera cholumikizira mawaya; Onani fuse ya DC. |
| Kulephera kulankhulana | Onani ngati zolumikizira za RS485 ndizolondola; Onani ngati kulumikizana kwa baud ndi kuyimitsa pang'ono kumagwirizana. |
Zolemba / Zothandizira
 |
SmartGen HMC4000RM Remote Monitoring Controller [pdf] Buku Logwiritsa Ntchito HMC4000RM, HMC4000RM Remote Monitoring Controller, Remote Monitoring Controller, Monitoring Controller, Controller |
