security Plus RB6C Billion Code Keychain Remotes Instruction Manual

RB6C Billion Code Keychain Remotes

“

ഉൽപ്പന്ന വിവരം

സ്പെസിഫിക്കേഷനുകൾ:

• Product Name: Replacement Remote for Security+ Family / Billion
  കോഡ്
• Compatibility: Works with Garage Door Openers using Security+
  or Billion Code technology
• LED Indicator: Learn LED (Green/Red/Orange, Purple,
  മഞ്ഞ)

ഉൽപ്പന്ന ഉപയോഗ നിർദ്ദേശങ്ങൾ

Step 1: Locate Smart / Learn Button

Locate the Smart / Learn button on your garage door opener. Use
a ladder if needed.

Step 2: Check Working Mode on Remote

The remote has two working modes. To check the working mode,
press and hold the button. Observe LED status:

LED നില	മോഡ് #	ഓപ്പണർ തരം
സോളിഡ്	മോഡ് 1	Purple/Red/Orange
ഫ്ലാഷിംഗ്	മോഡ് 2	മഞ്ഞ/പച്ച

ഘട്ടം 3: ഗാരേജ് ഡോർ ഓപ്പണർ ലേണിംഗ്

Press the learn button on the back of the opener. After the
learn LED glows steadily, press and hold the button on the remote
until the opener lights flash or you hear two clicks. Your remote
is successfully programmed.

Step 4: Change Working Mode on Remote

1. Using the Visor Clip, press and hold the PROG button on the
   back of the remote for 3 seconds until the LED flashes, then
   റിലീസ്.
2. Press and release the button of the remote. The LED will change
   to either SOLID (Mode 1) or FLASHING (Mode 2). Try programming it
   again with the opener (Step 3).

പതിവ് ചോദ്യങ്ങൾ (FAQ)

Q: What should I do if my remote’s working mode doesn’t match
my opener’s learn button color?

A: If the working modes do not match, follow Step 4 to change
the working mode on your remote before proceeding with
പ്രോഗ്രാമിംഗ്.

"`

Replacement Remote for Security+ Family / Billion Code Installation Manual

ഗാരേജ് ഡോർ ഓപ്പണറിനുള്ള പ്രോഗ്രാമിംഗ് നിർദ്ദേശങ്ങൾ

LED പഠിക്കുക

LED പഠിക്കുക

Green or Red/Orange

പർപ്പിൾ

മഞ്ഞ

1

നിങ്ങളുടെ ഗാരേജ് ഡോർ ഓപ്പണറിൽ സ്മാർട്ട് / ലേൺ ബട്ടൺ കണ്ടെത്തുക (നിങ്ങൾക്ക് ഒരു ഗോവണി ആവശ്യമാണ്).

2

Check the Working Mode on Remote

The remote has two working modes for different garage door opener types.

To check the working mode. Just press and hold the button. Then observe LED status.

LED Status SOLID FLASHING

Mode # Mode 1 Mode 2

For Opener Type Purple/ Red/Orange Yellow/ Green

Check above table, Does remote button’s working mode match your opener’s learn button color (as seen in Step 1)?

If yes, proceed to Step 3
If no, you will need to change working mode first, proceed to Step 4

3 Garage Door Opener Learning

Press the learn button on the back of the

opener. After the learn LED glows steadily,

press and hold the button on the remote until the

ClCiclikck

opener lights flash or you hear two clicks. At that point, the remote

പഠിക്കുക ബട്ടൺ

is successfully programmed.

4

Change the Working Mode on Remote

1. Using the Visor Clip to press and hold the “PROG” button on the back of the remote for 3 seconds until the LED flashes, then release.

2. Press and release the button of the remote, LED will change to either SOLID(Mode 1) or FLASHING (Mode 2). Then try program it again with opener (step 3).

പ്രമാണങ്ങൾ / വിഭവങ്ങൾ

security Plus RB6C Billion Code Keychain Remotes [pdf] നിർദ്ദേശ മാനുവൽ RB6C Billion Code Keychain Remotes, RB6C, Billion Code Keychain Remotes, Code Keychain Remotes, Keychain Remotes

റഫറൻസുകൾ

• ഉപയോക്തൃ മാനുവൽ