security Plus RB6C Billion Code Keychain Remotes Instruction Manual

RB6C Billion Code Keychain Remotes

“

پيداوار جي ڄاڻ

وضاحتون:

• Product Name: Replacement Remote for Security+ Family / Billion
  ڪوڊ
• Compatibility: Works with Garage Door Openers using Security+
  or Billion Code technology
• LED Indicator: Learn LED (Green/Red/Orange, Purple,
  پيلو)

پيداوار جي استعمال جون هدايتون

Step 1: Locate Smart / Learn Button

Locate the Smart / Learn button on your garage door opener. Use
a ladder if needed.

Step 2: Check Working Mode on Remote

The remote has two working modes. To check the working mode,
press and hold the button. Observe LED status:

ايل آئي ڊي اسٽيٽس	موڊ #	اوپنر جو قسم
سولڊ	موڊ 1	Purple/Red/Orange
چمڪڻ	موڊ 2	پيلو / سائو

قدم 3: گيراج دروازو اوپنر سکيا

Press the learn button on the back of the opener. After the
learn LED glows steadily, press and hold the button on the remote
until the opener lights flash or you hear two clicks. Your remote
is successfully programmed.

Step 4: Change Working Mode on Remote

1. Using the Visor Clip, press and hold the PROG button on the
   back of the remote for 3 seconds until the LED flashes, then
   ڇڏڻ.
2. Press and release the button of the remote. The LED will change
   to either SOLID (Mode 1) or FLASHING (Mode 2). Try programming it
   again with the opener (Step 3).

اڪثر پڇيا ويندڙ سوال (FAQ)

Q: What should I do if my remote’s working mode doesn’t match
my opener’s learn button color?

A: If the working modes do not match, follow Step 4 to change
the working mode on your remote before proceeding with
پروگرامنگ.

“`

Replacement Remote for Security+ Family / Billion Code Installation Manual

گيراج دروازو کولڻ لاءِ پروگرامنگ جون هدايتون

سکو LED

سکو LED

Green or Red/Orange

واڱڻائي

پيلو

1

ateوليو سمارٽ / سکو بٽڻ پنھنجي گيراج جي دروازي تي (توھان کي ھڪڙي ڏاڪڻ جي ضرورت پوندي).

2

Check the Working Mode on Remote

The remote has two working modes for different garage door opener types.

To check the working mode. Just press and hold the button. Then observe LED status.

LED Status SOLID FLASHING

Mode # Mode 1 Mode 2

For Opener Type Purple/ Red/Orange Yellow/ Green

Check above table, Does remote button’s working mode match your opener’s learn button color (as seen in Step 1)?

If yes, proceed to Step 3
If no, you will need to change working mode first, proceed to Step 4

3 Garage Door Opener Learning

Press the learn button on the back of the

opener. After the learn LED glows steadily,

press and hold the button on the remote until the

ClCiclikck

opener lights flash or you hear two clicks. At that point, the remote

سکو بٽڻ

is successfully programmed.

4

Change the Working Mode on Remote

1. Using the Visor Clip to press and hold the “PROG” button on the back of the remote for 3 seconds until the LED flashes, then release.

2. Press and release the button of the remote, LED will change to either SOLID(Mode 1) or FLASHING (Mode 2). Then try program it again with opener (step 3).

دستاويز / وسيلا

security Plus RB6C Billion Code Keychain Remotes [pdf] هدايت نامو RB6C Billion Code Keychain Remotes, RB6C, Billion Code Keychain Remotes, Code Keychain Remotes, Keychain Remotes

حوالو

• استعمال ڪندڙ دستي