XTOOL X2MBIR Kaihanga Papatono
Whakakahoretanga
Please read this manual carefully before using X2Prog Module Programmer (herein after referred to as X2Prog). Shenzhen Xtooltech Intelligent Co., Ltd. (herein after referred to as “Xtooltech”) does not assume any liability in case of misuse of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.
Whakaahuatanga Hua
Ko X2Prog he Kaihanga Papatono ka taea te panui, te tuhi me te whakarereke i nga raraunga maramara EEPROM me MCU ma te tikanga BOOT. He pai tenei taputapu mo nga miihini waka ngaio, miihini miihini ranei, e whakarato ana i nga mahi penei i te kati kōwae, te whakarereke, te whakakapi ranei mo te ECU, BCM, BMS, papatohu me etahi atu waahanga. Kei te kaha ano a X2Prog me etahi atu waahanga whakawhanui e whakaratohia ana e Xtooltech, ka taea te maha atu o nga mahi penei i te BENCH programming, transponder coding me te maha atu.
Hua View
- ① DB26 Port: Use this port to connect with cables or wiring harnesses.
- ② Indicators: 5V (Red / Left): This light will be turned on when X2Prog receives 5V power input. Communication (Green / Middle): This light will be flashing when the device is communicating. 12V (Red / Right): This light will be turned on when X2Prog receives 12V power input.
- ③ ④ Expansion Ports: Use these ports to connect with other expansion modules.
- ⑤ 12V DC Power Port: Connect to 12V power supply when necessary.
- ⑥ USB Type-C Port: Use this USB port to connect with XTool devices or PC.
- ⑦ Nameplate: Show product information.
Whakaritenga Pūrere
- XTool devices: APP version V5.0.0 or higher;
- PC: Windows 7 teitei ake ranei, 2GB RAM
Hononga Pūrere
Roha me te Hononga Taura
X2Prog is adapted to various expansion modules or cables for extra functions. Different modules are needed in different situations.
To install expansion modules, directly connect the modules to X2Prog using the expansion ports (32/48PIN) or the DB26 port.
Multiple expansion modules can be installed on X2Prog at the same time. When you are operating, check the device and see which modules are necessary.
Me pehea te Panui me te Tuhi EEPROM
Ma te Poari EEPROM
*EEPROM Board only comes with X2Prog standard pack.
When reading EEPROM in this method, the chip should be taken off from the ECU and needs to be soldered onto the EEPROM board.
He huarahi ke atu ki te panui EEPROM ma te whakamahi i nga waahanga roha. Tena koa tirohia nga hoahoa i runga i te taupānga ka kite me pehea e taea ai e koe te hono atu ki te maramara.
Me pehea te Panui me te Tuhi MCU
PUTAU
When reading MCU in this method, the wiring harness should be soldered to the ECU board according to the wiring diagram, and a 12V power supply should be connected to X2Prog.
I te wa e panui ana te MCU i tenei tikanga, me hono te waea waea ki te tauranga ECU kia rite ki te hoahoa waea, me hono te hiko 12V ki te X2Prog.
Whakapā mai ki a US
- Ratonga Kiritaki:
tautoko@xtooltech.com - Whaimana Webpae:
https://www.xtooltech.com/ - Wāhi noho:
17&18/F, Whare A2, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, Haina - Corporate & Business:
marketing@xtooltech.com
© Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, All Rights Reserved
Nga Korero Tautukunga
Tautukunga FCC
FCC ID: 2AW3IM604
Ka tutuki tenei taputapu ki te Wahanga 15 o nga Ture FCC. Ko te mahi i raro i nga tikanga e rua e whai ake nei:
- Kare pea tenei taputapu e whakararu kino
- Me whakaae tenei taputapu ki nga pokanoa kua tae mai, tae atu ki te pokanoa ka puta he mahi kore.
Whakatupato
Ko nga huringa me nga whakarereketanga kaore i tino whakaaehia e te roopu kawenga mo te hanganga ture ka whakakorehia te mana o te kaiwhakamahi ki te whakahaere i nga taputapu.
Tuhipoka
Kua whakamatauria tenei taputapu, kua kitea e u ana ki nga rohe mo tetahi taputapu matihiko Class B, i runga i te Wahanga 15 o nga Ture FCC. I hoahoatia enei rohe ki te whakarato i te whakamarumaru tika mai i nga pokanoa kino i roto i te whakaurunga whare.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Whakahoahoa, nukuhia ranei te antenna whiwhi.
- Whakanuia te wehenga i waenga i nga taputapu me te kaiwhiwhi.
- Honoa te taputapu ki tetahi putanga i runga i te ara iahiko rereke mai i tera e hono ana te kaikawe.
- Korero atu ki te kaihoko, ki tetahi tohunga hangarau reo irirangi/TV mo te awhina.
Nga Tauākī Whakatupato Whakaaturanga RF:
Ko enei taputapu e whai ana ki nga tepe whakamaarama iraruke FCC kua whakaritea mo te taiao kore whakahaere. Ko enei taputapu me whakauru me te whakahaere me te iti rawa o te tawhiti 20cm i waenga i te radiator me te tinana.
Rōpū Haepapa
- Company name: TianHeng Consulting, LLC
- Wāhi noho: 392 Andover Street, Wilmington, MA 01887, United States
- Ī-mēra: tianhengconsulting@gmail.com
Tauākī ISED
- IC: 29441-M604
- PMN: M604, X2MBIR
- HVIN: M604
Kei roto i tenei taputapu nga kai tuku raihana-waahi/kaiwhiwhi e u ana ki nga RSS kua whakakorehia te raihana hou, Pūtaiao me te Whanaketanga Ohaoha a Canada.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Whakapuakanga o te rite
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.
FAQ
- Q: He aha nga whakaritenga taputapu mo te whakamahi i te X2MBIR Module Kaihōtaka?
A: The X2MBIR Module Programmer requires XTool devices with APP version V5.0.0 or higher and a PC running on Windows 7 or higher with a minimum of 2GB RAM. - Q: Me pehea taku panui me te tuhi i nga raraunga EEPROM me te X2Prog?
A: To read and write EEPROM data, use the provided EEPROM Board included in the standard pack. Remove the chip from the ECU and solder it onto the EEPROM board. - Q: Ka taea e au te whakamahi i nga waahanga roha maha i te wa kotahi me te X2Prog?
A: Yes, multiple expansion modules can be installed on X2Prog at the same time. Ensure you connect them correctly to enhance functionality.
Tuhinga / Rauemi
 |
XTOOL X2MBIR Kaihanga Papatono [pdf] Aratohu Kaiwhakamahi M604, X2MBIR Kaihanga Papatono, X2MBIR, Kaihanga Papatono, Kaihanga Papatono |