XTOOL X2MBIR moduli dasturchisi
Rad etish
Please read this manual carefully before using X2Prog Module Programmer (herein after referred to as X2Prog). Shenzhen Xtooltech Intelligent Co., Ltd. (herein after referred to as “Xtooltech”) does not assume any liability in case of misuse of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.
Mahsulot tavsifi
X2Prog BOOT usuli orqali EEPROM va MCU chip ma'lumotlarini o'qiy oladigan, yozishi va o'zgartirishi mumkin bo'lgan modul dasturchisi. Ushbu qurilma modullarni klonlash, modifikatsiyalash yoki ECU, BCM, BMS, asboblar paneli yoki boshqa modullarni almashtirish kabi funksiyalarni ta'minlovchi professional avtomobil tyunerlari yoki mexanizatorlari uchun javob beradi. X2Prog, shuningdek, Xtooltech tomonidan taqdim etilgan boshqa kengaytirish modullari bilan ishlaydi, bu esa BENCH dasturlash, transponder kodlash va boshqalar kabi ko'proq funktsiyalarni ta'minlaydi.
Mahsulot View
- ① DB26 Port: Use this port to connect with cables or wiring harnesses.
- ② Indicators: 5V (Red / Left): This light will be turned on when X2Prog receives 5V power input. Communication (Green / Middle): This light will be flashing when the device is communicating. 12V (Red / Right): This light will be turned on when X2Prog receives 12V power input.
- ③ ④ Expansion Ports: Use these ports to connect with other expansion modules.
- ⑤ 12V DC Power Port: Connect to 12V power supply when necessary.
- ⑥ USB Type-C Port: Use this USB port to connect with XTool devices or PC.
- ⑦ Nameplate: Show product information.
Qurilmaga qo'yiladigan talablar
- XTool devices: APP version V5.0.0 or higher;
- Kompyuter: Windows 7 yoki undan yuqori, 2 GB operativ xotira
Qurilma ulanishi
Kengaytirish va kabel ulanishi
X2Prog is adapted to various expansion modules or cables for extra functions. Different modules are needed in different situations.
To install expansion modules, directly connect the modules to X2Prog using the expansion ports (32/48PIN) or the DB26 port.
Multiple expansion modules can be installed on X2Prog at the same time. When you are operating, check the device and see which modules are necessary.
EEPROMni qanday o'qish va yozish
EEPROM platasi orqali
*EEPROM Board only comes with X2Prog standard pack.
When reading EEPROM in this method, the chip should be taken off from the ECU and needs to be soldered onto the EEPROM board.
Kengaytirish modullari yordamida EEPROMni o'qishning boshqa usullari mavjud. Iltimos, ilovadagi diagrammalarni tekshiring va chipga qanday ulanishni ko'ring.
MCU-larni qanday o'qish va yozish kerak
BOOT
When reading MCU in this method, the wiring harness should be soldered to the ECU board according to the wiring diagram, and a 12V power supply should be connected to X2Prog.
MCU ni ushbu usulda o'qiyotganda, simni ulash sxemasi bo'yicha simi simi ECU portiga ulangan bo'lishi kerak va X12Prog ga 2V quvvat manbai ulanishi kerak.
Biz bilan bog'lanish
- Mijozlarga xizmat ko'rsatish:
supporting@xtooltech.com - Rasmiy Websayt:
https://www.xtooltech.com/ - Manzil:
17&18/F, A2 binosi, Creative City, Liuxian Avenue, Nanshan tumani, Shenzhen, Xitoy - Corporate & Business:
marketing@xtooltech.com
© Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, All Rights Reserved
Muvofiqlik haqida ma'lumot
FCC muvofiqligi
FCC ID: 2AW3IM604
Ushbu qurilma FCC qoidalarining 15-qismiga mos keladi. Operatsiya quyidagi ikkita shartga bog'liq:
- Ushbu qurilma zararli shovqinlarga olib kelmasligi mumkin
- Ushbu qurilma qabul qilingan har qanday shovqinni, jumladan, kiruvchi ishlashga olib kelishi mumkin bo'lgan shovqinlarni qabul qilishi kerak.
Ogohlantirish
Muvofiqlik uchun mas'ul tomon tomonidan aniq tasdiqlanmagan o'zgartirishlar yoki modifikatsiyalar foydalanuvchining uskunani ishlatish vakolatini bekor qilishi mumkin.
Eslatma
Ushbu uskuna sinovdan o'tkazildi va FCC qoidalarining 15-qismiga muvofiq, B sinfidagi raqamli qurilma uchun cheklovlarga mos kelishi aniqlandi. Bu chegaralar turar joyni o'rnatishda zararli shovqinlardan oqilona himoya qilish uchun mo'ljallangan.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Qabul qiluvchi antennaning yo'nalishini o'zgartiring yoki o'zgartiring.
- Uskuna va qabul qilgich orasidagi masofani oshiring.
- Uskunani qabul qilgich ulanganidan farqli zanjirdagi rozetkaga ulang.
- Yordam uchun diler yoki tajribali radio/televidenie bo'yicha mutaxassis bilan maslahatlashing.
RF ta'siri haqida ogohlantirish bayonotlari:
Ushbu uskuna nazoratsiz muhit uchun belgilangan FCC radiatsiya ta'sir qilish chegaralariga mos keladi. Ushbu uskuna radiator va korpus o'rtasida kamida 20 sm masofada o'rnatilishi va ishlashi kerak.
Mas'uliyatli partiya
- Company name: TianHeng Consulting, LLC
- Manzil: 392 Andover Street, Wilmington, MA 01887, Amerika Qo'shma Shtatlari
- E-mail: tianhengconsulting@gmail.com
ISED bayonoti
- IC: 29441-M604
- PMN: M604, X2MBIR
- HVIN: M604
Ushbu qurilmada Kanadaning Innovatsiya, Fan va Iqtisodiy Taraqqiyot RSS(lar)iga mos keladigan litsenziyasiz uzatuvchi(lar)/qabul qiluvchi(lar) mavjud.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Muvofiqlik deklaratsiyasi
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.
TSS
- Savol: X2MBIR modulidan foydalanish uchun qurilma talablari qanday Dasturchi?
A: The X2MBIR Module Programmer requires XTool devices with APP version V5.0.0 or higher and a PC running on Windows 7 or higher with a minimum of 2GB RAM. - Savol: X2Prog yordamida EEPROM ma'lumotlarini qanday o'qiyman va yozaman?
A: To read and write EEPROM data, use the provided EEPROM Board included in the standard pack. Remove the chip from the ECU and solder it onto the EEPROM board. - Savol: bilan bir vaqtning o'zida bir nechta kengaytirish modullaridan foydalansam bo'ladimi? X2Prog?
A: Yes, multiple expansion modules can be installed on X2Prog at the same time. Ensure you connect them correctly to enhance functionality.
Hujjatlar / manbalar
 |
XTOOL X2MBIR moduli dasturchisi [pdf] Foydalanuvchi uchun qoʻllanma M604, X2MBIR modul dasturchisi, X2MBIR, modul dasturchisi, dasturchi |