TONSTAD

General Assembly Information

Before starting assembly, ensure you have the necessary tools. Recommended tools include screwdrivers (Phillips and flathead) and a hammer. [?] [?]

Follow the instructions carefully. Avoid assembling on hard surfaces that could scratch the product. [❌]

Ensure parts are correctly oriented and assembled. Do not force parts together. [❌]

If you encounter difficulties, consult the IKEA website or contact IKEA customer support. [❓] [?]

Parts List

Hardware

• 14x Screw (Part ID: 154409)
• 8x Threaded Rod (Part ID: 100038)
• 1x Allen Key (Part ID: 120202)
• 4x Dowel Pin (Part ID: 110912)
• 8x Pin (Part ID: 101350)
• 4x Foot/Glider (Part ID: 09722)
• 16x Screw (Part ID: 130886)
• 16x Screw (Part ID: 130884)
• 8x Nut (Part ID: 100712)
• 8x Washer (Part ID: 100843)

Components

• 4x Bracket (Part ID: 10116225)

Step 1

Attach four brackets (Part ID: 10116225) to the underside of the table frame. Use four screws (Part ID: 130886) and four screws (Part ID: 130884) per bracket, totaling 16 screws of each type.

The diagram shows the bracket being positioned and secured with screws. A close-up shows the screw insertion.

Step 2

Insert two screws (Part ID: 130886) and two screws (Part ID: 130884) into the pre-drilled holes of each of the four brackets attached in Step 1. Ensure the screws are oriented correctly.

The diagram shows the insertion of screws into the brackets. Arrows indicate the direction of insertion and rotation. A "no" symbol [❌] indicates incorrect insertion or orientation.

Step 3

Assemble the table frame. Insert eight pins (Part ID: 101350) into the designated holes on the frame pieces. Secure the frame by inserting eight screws (Part ID: 101350) into the frame, using the provided Allen key (Part ID: 120202).

The diagram shows the frame pieces being joined with pins and screws. An inset shows the Allen key being used to tighten a screw.

Step 4

Place the assembled frame onto a soft surface, such as a rug, to prevent scratching. Insert eight screws (Part ID: 154409) into the pre-drilled holes on the underside of the frame.

The diagram shows the frame being placed on a rug. An inset shows screws being inserted into the frame's underside.

Step 5

Attach the table legs. Insert fourteen screws (Part ID: 154409) through the frame and into the legs. The diagram shows the screws being inserted and tightened.

The diagram shows the table frame with screws being inserted into the leg attachment points. A close-up shows the screw and its path.

Step 6

Connect the leg components. Insert four threaded rods (Part ID: 100038) into the leg structures. Then, insert four dowel pins (Part ID: 110912) into the corresponding holes. The diagram shows the insertion of rods and pins into the leg assembly.

The diagram shows the leg assembly with threaded rods and dowel pins being inserted. An inset shows the insertion of these parts.

Step 7

Attach the legs to the table frame. Insert four nuts (Part ID: 100712) and four washers (Part ID: 100843) onto the threaded rods protruding from the leg assembly. Secure these using the Allen key (Part ID: 120202).

The diagram shows the leg assembly being attached to the table frame. Nuts and washers are placed onto threaded rods, and the Allen key is used for tightening.

Step 8

Secure the legs to the table frame. Use four feet/gliders (Part ID: 107271) and a hammer to tap them into the bottom of the legs. The diagram shows the feet being hammered into place.

The diagram shows the final step of attaching the feet/gliders to the bottom of the table legs using a hammer.