Onforu LED Flood Light Product Manual

Components and Structure

Models: 125BL/D50BL/D100BL

• 1. Cover
• 2. LED Light Source
• 3. Lamp Bracket

Models: G20BL/G50BL/D100BL

• 1. Cover
• 2. LED Light Source
• 3. Lamp Bracket
• 4. Antenna

Specifications

Models: 125BL, D50BL, D100BL

Models: G20BL, G50BL, D100BL

Dimensions

Models: 125BL, D50BL, D100BL

Models: G20BL, G50BL, D100BL

Pairing LED Light with "Onforu" App

Step 1: "Onforu Home" App Download

Download the "Onforu Home" App from the App Store or Google Play, or scan the QR code provided.

Step 2: Enter the "Onforu Home" App

Register an account or log in with an existing account. Note: Your "Onforu Home" App username and password are required for pairing with Amazon Alexa and/or Google Assistant.

Step 3: Enable Wi-Fi and Bluetooth

Ensure Wi-Fi and Bluetooth are turned on before connecting the LED lights to the "Onforu Home" App.

Step 4: How to Pair the LED Light

Method 1: Automatic Search

1. Tap the '+' button on the top right corner and select "Add Device".
2. The app will automatically search for the device. Tap "Add" when discovered.
3. Wait for the device to register (approximately 5-10 seconds).
4. Upon completion, tap "Done" to enter the control panel. You can optionally change the device name.

Method 2: Manual Selection

1. Tap the '+' button on the top right corner and select "Add Device".
2. Navigate to "Lighting" and then "Light Source(BLE)".
3. Tap the "Next" button to begin pairing.
4. Wait for the device to register (approximately 5-10 seconds).
5. Upon completion, tap "Done" to enter the control panel. You can optionally change the device name.

Setting the light to pending pairing state:

1. Power on the LED Light.
2. Turn the light on and off three times: on-off (wait 2s); on-off (wait 2s); on-off (wait 2s); on.
3. The warm white light will flash slowly, indicating it is ready for pairing.

App Operating Instructions

RGB Color Interface

• Select desired color.
• Adjust color brightness.
• Use presets to save frequently used colors.
• Set a timer.

White-light Mode Interface

• Adjust the color brightness.
• Use presets to save common brightness modes.
• Set a timer.

DIY Mode Interface

• Set the desired color.
• Select the rhythm mode.
• Adjust the brightness and speed.

Scene Mode Interface

• Set color's jump, brightness modes.
• Adjust the brightness and speed.

Music Mode Interface

The light will change color and brightness following music collected by the microphone.

How to Control Lights in Groups

Note: Lights must be online to be grouped.

1. From any mode screen, click "More" on one of the lights.
2. Select "Create Group".
3. Enter a group name (e.g., "mesh RGBW Group").
4. Add desired devices to the group.
5. Save the group. You can now operate the lights within the group via the app.

Installation

Preparation

• Check all components for damage. Do not use if damaged.
• Estimated Assembly Time: 10-30 minutes.
• Tools Required (not included): Flathead screwdriver, Pliers, Electric drill, Eye Protection, Step Ladder.

CAUTION:

Ensure the wall switch and main circuit breaker are OFF before installation. Consult a licensed electrician if unsure about electrical installation.

WARNINGS:

• Installing this light in an ungrounded electrical system can lead to electric shock if wires are damaged or loose.
• Be careful not to damage wire insulation during installation. Avoid sharp edges.
• This product must be installed according to applicable codes by a qualified person.
• RISK OF SHOCK: Turn off electricity at the circuit breaker or main fuse box before starting installation.

Installation Steps:

1. Drill two mounting holes on the mounting surface according to the spacing of the LED Light bracket (refer to diagram 'A').
2. Attach the bracket to the mounting holes and secure it with screws.
3. Adjust the beam direction as desired and proceed with wiring.
4. Plug the light into the main socket.

FCC Information

FCC ID: 2BM4TD100BL

FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.