Onforu LED RGB Flood Light

Safety Information

General Safety Precautions:

• Always disconnect the power supply before performing any work on the unit.
• Installation involves working with mains voltage and must be carried out by a licensed professional electrician in accordance with national wiring regulations.
• Check all components for damage before installation. Do not use if damaged.
• Ensure the product is used within the voltage range specified on the lamp label.
• The floodlight enclosure heats up during operation. Adjust the angle of the light only after the power has been off for 10-15 minutes. Avoid looking directly into the LED light at close range or for prolonged periods (>5 min).
• Do not install on flammable surfaces.
• Do not alter or replace parts of the light to avoid accidents like breakage, falls, electric shock, or fire.
• To reduce the risk of strangulation, secure flexible wiring to the wall if it is within reach.
• The light is IP66 waterproof, but the plug is not. Connect the plug indoors or to an IP65-protected socket.
• Use tools to adjust the lights.
• The light source is not replaceable; the entire luminaire must be replaced when the light source reaches its end of life.
• Never plug in the light with wet hands to avoid electric shock.
• This is a non-dimmable product. Do not connect it to a dimming controller.
• Do not connect to an ungrounded electrical system. Connecting to an ungrounded system can cause metal parts to carry current if wires are damaged or loose, leading to electric shock, injury, or death.
• Use wire nuts/connectors rated for the correct gauge and number of wires. Ensure no exposed wire bundles are outside the connector.
• Be careful not to damage or cut wire insulation during installation. Keep wires away from sharp edges.
• The floodlight is supplied with a cable and must be terminated using a terminal block (not supplied) in a suitable IP-rated enclosure (not included).
• For Type Z attachments, the external flexible cable or cord cannot be replaced. If damaged, the luminaire must be destroyed.

Product Models and Specifications

The following models are available:

• G10RGB (12W)
• G20RGB (20W / 25W)
• D50RGB (50W)
• G50RGB (50W)
• D100RGB (100W)

Specifications:

Intended Use

This light is intended to create atmosphere and is not suitable for household room illumination or other applications.

Remote Control Operation

The remote control allows for various functions:

• Memory Function: The light starts with the last selected color and mode.
• Brightness Adjustment: Increase or decrease brightness across 8 levels using the "⬆" or "⬇" buttons.
• Pause Mode: Pause color changes in jump, fade, flash, or automatic modes using the "pause" button.
• On/Off: Turn the light on or off with the "power" button.
• Color Options: Select colors using the colored buttons.
• DIY Mode: Customize colors by adjusting RGB brightness using 6 keys. Up to 17 variations and over 4,800 colors can be saved as DIY1, DIY2, or DIY3.
• Speed Adjustment: Adjust color change speed in jump, fade, and flash modes using QUICK (faster) and SLOW (slower) buttons. 30 speed levels are available.
• Timing: Set the timer for 3H, 6H, or 12H intervals, after which the light will automatically turn off.
• Auto Mode: Freely switch between Flash, Jump, and Fade modes.
• Flash Mode: Makes the light flash.
• Fade Mode: FADE3 for 3-color gradients, FADE7 for 7-color gradients.
• Jump Mode: JUMP3 for 3-color jumps, JUMP7 for 7-color jumps.
• Remote Battery Replacement: Use a CR2025 lithium button battery. Remove the insulation sheet before first use. Dispose of batteries separately.

Components and Structure

The floodlight consists of:

• 1. Tempered Glass Lid
• 2. LED Light Source
• 3. Lamp Bracket

Cable specifications vary by region:

• US: 1m (3.28ft) H05RN-F 3x18AWG
• EU: 1m (3.28ft) H05RN-F 3x1.0mm²
• UK: 1m (3.28ft) H05RN-F 3x1.0mm²

Notes and Limitations

• Distance: Ensure a distance of more than 1 meter between the light and the illuminated object to avoid high temperatures from short distances.
• Ground Wire: An earth wire is required for electrical safety.
• Insulation: Do not cover the lamps with thermal insulation materials.
• Usage: Not suitable for household room illumination.
• Waterproof: The light is waterproof and dustproof, protected against rain but not submersible in water.
• Mounting: The mounting position must support at least 10 times the weight of the light.
• Power: Powered by High Voltage Alternating Current (HVAC). Connect to the ground wire and keep out of reach.
• Heat Dissipation: Use in conditions with good heat dissipation. Operating temperature should be below 40°C. High temperatures can cause lumen depreciation and affect lifespan.

Installation Steps

1. Drill two mounting holes based on the spacing of the screw bits on the LED Light bracket (see part "A" of the picture).
2. Place the bracket onto the prepared mounting holes and screw it in.
3. Adjust the beam direction as desired, then plug into the main socket.

NOTE: Recommended installation height not higher than 5 m (16.4 ft).

Operation & Maintenance

• Before cleaning, disconnect the power supply.
• The unit is not suitable for burglar alarm systems due to lack of tamperproof security.
• Do not use chemicals or corrosive substances for cleaning.

Disposal

Electrical and electronic equipment, accessories, and packaging must be recycled in an environmentally compatible manner. Do not dispose of as domestic waste. Follow EU directives for separate collection and recycling.

Manufacturer Information

Manufacturer: Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si

Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen Zhen, Guang Dong, 518000, CN

Contact: support@onforuled.com | www.onforuleds.com

EU Representative: MDH LIGHTING LTD, Suite 302, 292 Strovolos Avenue, 2048 Strovolos, Nicosia, Cyprus

UK Representative: MDH LIGHTING LTD, 69 Aberdeen Avenue, Cambridge CB2 8DL, United Kingdom