Onforu RGB LED Light

Models

• CTB48RGB
• CTB72RGB
• CTB96RGB

Available voltage options:

• US: 100-120V AC
• EU: 220-240V AC
• UK: 220-240V AC

Safety Information

WARNING: Disconnect the power supply before attempting any work on the unit. Installation involves work on mains voltage supply and must be carried out professionally in accordance with national wiring regulations and electrical operating conditions by a licensed professional electrician.

• Check all components for damage; do not use if damaged.
• Use within the voltage range specified on the lamp label for normal operation.
• The floodlight enclosure heats up during operation. Adjust the angle only after power off for 10-15 minutes. Do not look directly into the LED light at close range or for prolonged periods (>5 min).
• Do not install on flammable surfaces.
• Do not alter or change parts of the light to avoid accidents (breakage, fall, electric shock, fire).
• Secure flexible wiring to the wall if within arm's reach to reduce strangulation risk.
• The light is IP66 waterproof, but the plug is not. Connect the plug indoors or to a socket providing IP65 protection.
• Use tools to adjust the lights.
• The light source is not replaceable; the entire luminaire must be replaced at its end of life.
• Never plug in with wet hands to avoid electric shock.
• This is a non-dimmable product. Do not connect it with a dimming controller.
• Do not connect to an ungrounded electrical system. Connecting to an ungrounded system may cause metal parts to carry current if wires are damaged or loose, leading to electric shock, injury, or death.
• Use wire nuts/connectors rated for the correct gauge and number of wires. Ensure no exposed wire bundles outside the connector.
• Be careful not to damage or cut wire insulation during installation. Keep wires away from sharp edges.
• The floodlight is supplied with cable and must be terminated using a terminal block (not supplied) in a suitable IP-rated enclosure (not included).
• For Type Z attachments: The external flexible cable or cord cannot be replaced; if damaged, the luminaire must be destroyed.

Parameters

Intended Purpose

This light is intended for special purpose use to create atmosphere. It is not suitable for household room illumination or other applications.

Components and Structure

The product includes the following components:

1. Tempered Glass Lid
2. LED Light Source
3. Lamp Bracket
4. Screws For Mounting
5. Plastic Expansion Nails
6. Screws
7. Lamp Brackets
8. Hex Screw Key
9. Remote Control

Max Projected Area:

• A: 0.0255m²
• B: 0.0309m²
• C: 0.0346m²
• D: 0.0542m²

Remote Control Operation

The light can start with the last selected color and mode due to its memory function.

1. Brightness Adjustment: Press the [brightness up] or [brightness down] buttons to adjust brightness across 8 levels.
2. Stop: Pause color changes in jump, fade, flash, or automatic modes.
3. On/Off: Press the [power] button to turn the light on or off.
4. Color Options: Press the colored buttons to select the corresponding light color.
5. DIY Mode: Press DIY1, DIY2, or DIY3. Use the 6 RGB brightness keys to create custom colors. Up to 17 variations and over 4,800 colors can be saved across DIY1, DIY2, and DIY3.
6. Speed Adjustment: Adjust the speed of color changes in jump, fade, and flash modes using the [QUICK] and [SLOW] buttons. 30 speed options are available.
7. Timing: Set the timer for 3H, 6H, or 12H. The light will automatically turn off when the timer expires.
8. Auto Mode: Freely switch between Jump, Fade, or Flash modes.
9. Flash Mode: Makes the light flash.
10. Fade Mode: FADE3 is a 3-color gradient mode; FADE7 is a 7-color gradient mode.
11. Jump Mode: JUMP3 is a 3-color jump mode; JUMP7 is a 7-color jump mode.
12. Remove the insulation sheet from the remote control before first use.

Remote Control Battery Replacement: Replace batteries as shown in the diagram.

Notes and Limitations of Use

• Ensure the distance between the light and the illuminated object is more than 1 meter to avoid high temperatures caused by short distances.
• An earth wire is required for electrical safety.
• The lamps are not suitable for covering with thermal insulation materials.
• This light is not suitable for household room illumination.
• The light is waterproof and dustproof, protected against rain but not submersible in water.
• The mounting position must support at least 10 times the weight of the light.
• The light is powered by High Voltage Alternating Current (HVAC). Connect to the ground wire and keep out of easy reach.
• Use in conditions with good heat dissipation. Working temperature should be below 40°C (104°F). Excessive temperatures can cause lumen depression and reduce lifespan.
• The light source is not user-replaceable; only the manufacturer or a qualified agent can replace it.

Installation Steps

1. Fix the bracket onto the lamp using the combination screws.
2. Drill four mounting holes according to the spacing indicated (see diagram part 'A').
3. Position the brackets onto the prepared mounting holes and screw them in.
4. Adjust the beam direction as desired, then plug into the main socket.

NOTE: Recommended installation height is not higher than 5 m (16.4 ft).

Operation & Maintenance

• Before cleaning, ensure the light is disconnected from the power supply.
• The unit is not suitable for burglar alarm systems as it lacks the required tamperproof security.
• Never use chemicals or corrosive substances for cleaning.

Disposal

Electrical and electronic equipment, accessories, and packaging must be recycled in an environmentally compatible manner. Do not dispose of as domestic waste.

EU countries only: In accordance with the European Directive on Waste Electrical and Electronic equipment and national law, equipment no longer suitable for use must be collected separately and recycled.

Manufacturer Information

Manufacturer: Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si

Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen Zhen, Guang Dong, 518000, CN

Contact: support@onforuled.com | www.onforuleds.com

EU Representative: MDH LIGHTING LTD, Suite 302, 292 Strovolos Avenue, 2048 Strovolos Nicosia, Cyprus

UK Representative: MDH LIGHTING LTD, UNIT G25 WATERFRONT STUDIOS 1 DOCK ROAD LONDON UNITED KINGDOM E16 1AH

Made in China