PIR LED Wall Lights with Motion Sensor
Models: BDB55G-3, BDB100G-3
Product Components
The product comprises the following parts:
- 1. Cover
- 2. LED Light Source
- 3. Lamp Base
- 4. Sensor Head
Parts List
| Part | Description | Quantity |
|---|---|---|
| A | Machine Screw | 3 |
| B | Expansion Rubber Plug | 3 |
| C | EVA Gasket | 1 |
| D | Mounting Bracket | 1 |
| E | Wire Nuts | 3 |
| F | Long Machine Screw | 1 |
| G | Silicone Gasket | 1 |
| H | Machine Screw | 2 |
| I | Machine Screw | 2 |
| J | Remote control | 1 |
Specifications
| Model | Input Voltage | Input Current | Rated Power | Luminous Flux | CCT | CRI | Power Factor | L70B50 Lifetime | Beam Angle | Operating Temperature | Luminaire Location |
|---|---|---|---|---|---|---|---|---|---|---|---|
| BDB55G-3 | 100-120V 60Hz | 0.5A | 55W | 5500lm | 6500K | 80 | 0.9 | 30000hours L70B50 @25°C | 120° | -20-40°C / -4°F-104°F | SUITABLE FOR WET LOCATIONS |
| BDB100G-3 | 100-120V 60Hz | 0.83A | 100W | 9000lm | 6500K | 80 | 0.9 | 30000hours L70B50 @25°C | 120° | -20-40°C / -4°F-104°F | SUITABLE FOR WET LOCATIONS |
Note: The testing standard for luminous flux requires placing three/two lights on the same horizontal surface for testing; the tested luminous flux is the accurate luminous flux.
Dimensions
| Model | Dimensions (LxHxW) | Weight |
|---|---|---|
| BDB55G-3 | 272x123x121mm / 10.71x4.84x4.76 in | 0.98 kg / 2.16 lb |
| BDB100G-3 | 455x182x120 mm / 17.9x7.16x4.72 in | 1.53kg / 3.37lb |
Preparation and Installation
Estimated Assembly Time: 30-60 minutes.
Recommended Installation Height: 2.5m (8.2 ft) to 5 m (16.4 ft).
Tools Required (not included): Flathead screwdriver, Phillips screwdriver, Silicone Sealant, Eye Protection, Pliers, Step Ladder.
Safety Precautions:
⚡ RISK OF SHOCK: Turn off electricity at the circuit breaker or main fuse box before installation.
Ensure no exposed wire bundles are outside wire nuts/connectors.
Avoid damaging wire insulation and prevent wires from touching sharp edges.
⚠️ WARNING: Installation must comply with applicable codes and be performed by a qualified person familiar with the product and its hazards.
CAUTION: Ensure wall switch and main circuit breaker are off. Consult a licensed electrician if unsure about electrical installation.
⚠️ WARNING: Connect to a grounded electrical system. Attach the ground wire to the green ground screw on the mounting plate or the ground wire in the outlet box. Failure to do so can result in electric shock and injury or death.
Troubleshooting
| Malfunction | Cause | Remedy |
|---|---|---|
| LED senses a movement, the light does not light up | 1. Light not energized. 2. Surrounding light sources misjudge as daytime. 3. Brightness in night mode during the day. 4. Internal wiring loose. | 1. Check power status. 2. Turn off nearby lights or adjust sensor direction. 3. Reset. 4. Rewire after power failure. |
| LED sensor light did not go out, continued to light up | Continuous movement within the sensing range. | Check the relevant area and retune or override the sensor head if necessary. |
| LED sensor light illuminates during the day | 1. Shadows around the sensor mistaken for night. 2. Unstable light sources shining onto the sensor. | 1. Do not cover the sensor head. 2. Place the light in a bright area during the day. Avoid exposure to such light sources. |
| LED lights turn on unexpectedly | 1. Wind blows branches/bushes in range. 2. Sensing cars on the road. 3. Sudden temperature change (climate, fans, exhaust). | 1. Adjust its scope. 2. Adjust its scope. 3. Change irradiation area. |
Sensor Detection Range
Detection Range: 180°
Notes:
- 1. The PIR sensor shall always be tilted slightly downward.
- 2. The orientation angle of the sensor shall be between 0° and 45°.
Manufacturer and Contact Information
Manufacturer: HK Bright International Lighting Co., Limited
UK Importer: MDH LIGHTING LTD
Contact: support@onforuled.com
Website: www.onforuleds.com
Made in China.
Onforu LED Light - Colorful LED Lights Make Your Life More Colorful
