Safety Warnings and Important Information
- ⚠️CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- Ensure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
❗IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your local distributor for a replacement.
MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Product Specifications
| Feature | Specification |
|---|---|
| Model | GSDM003LP |
| VESA Compatibility | 75x75mm, 100x100mm |
| Max Screen Size | 32 inches |
| Max Laptop Size | 17.3 inches |
| Weight Capacity | 1-9kg (2.2-19.8lbs) per arm |
| Rated Max Load | 8kg (17.6lbs) |
Parts List
- Part A: Clamp Base (x1)
- Part B: Pole (x1)
- Part C: Clamp Arm (x1)
- Part D: Lower Arm (x1)
- Part E: Upper Arm (x2)
- Part F: VESA Plate (x1)
- Part G: Grommet Bolt (x1)
- Part H: Washer (x3)
- Part I: Allen Wrench (x1)
- Part J: Laptop Tray (x1)
- Part K: Laptop Tray Support Arm (x1)
- Part L: Cable Management Clip (x2)
- Part M: Pole Support (x3)
- Part N: Grommet Nut (x1)
- Part O: Desk Clamp Screw (x1)
- Part P: Laptop Tray Screw (x1)
Hardware
- M-A: M4x12 screws (x4)
- M-B: M4x16 screws (x4)
- M-C: M5x12 screws (x4)
- M-D: M5x16 screws (x4)
- M-E: M4x8 screws (x4)
- D5: Washers (x4)
- 2mm Allen Wrench (x1)
- 3mm Allen Wrench (x1)
- 6mm Allen Wrench (x1)
Assembly Instructions
Step 1: Prepare the Pole and Mount Base
Choose either the Desk Clamp Mount or the Grommet Mount.
1a: Desk Clamp Mount Assembly
- 1a-1a: Attach the Clamp Base (A) to the Pole (B) using screws (M-A). →
- 1a-2: Attach the Clamp Arm (C) to the Pole (B) using screws (M-B). →
- 1a-3: Secure the clamp assembly to the edge of your desk. Ensure it is firmly attached.
1b: Grommet Mount Assembly
- 1b-1: Insert the Grommet Bolt (G) through the desk's grommet hole. Attach the Clamp Base (A) to the bolt, followed by a Washer (H) and the Grommet Nut (N). Tighten securely. →
- 1b-2: Attach the Clamp Arm (C) to the Pole (B) using screws (M-B). →
Step 2: Attach Monitor Arms to the Pole
- 2b-1: Attach the Lower Arm (D) to the Pole (B) using screws (M-C). →
- 2b-2: Attach the Upper Arm (E) to the Lower Arm (D) using screws (M-D). →
Step 3: Secure Pole to Mount Base
Insert the Pole (B) into the assembled Clamp Base (A) or Grommet Mount assembly. Secure the pole using the Pole Supports (M) and screws (M-E). Ensure the pole is stable. →
Step 4: Attach VESA Plate to Upper Arm
Attach the VESA Plate (F) to the end of the Upper Arm (E) using screws (M-E) and Washers (D5). →
Step 5: Attach Laptop Tray
Attach the Laptop Tray Support Arm (K) to the VESA Plate (F) using screws (M-F). Then, attach the Laptop Tray (J) to the Support Arm (K) using screws (P). →
Step 6: Mount Monitors and Laptop
- Mount your monitor(s) onto the VESA Plate(s) (F) using the appropriate VESA screws (M-A or M-B) and Washers (D5). →
- Place your laptop onto the Laptop Tray (J).
Step 7: Adjust Gas Spring Tension
Use the provided Allen Wrench (I) to adjust the gas spring tension for each arm. Turn the adjustment screw (typically marked '+' or '-') to set the desired tension so the arm stays in place when you release it. Refer to the diagram for the location of the adjustment screw.
Diagram description: Shows an arm with a gas spring cylinder. An arrow points to an adjustment screw on the cylinder, with '+' and '-' markings indicating direction for increasing or decreasing tension.
Step 8: Cable Management
Attach the Cable Management Clips (L) along the arms and pole to route and secure your cables neatly. →
Step 9: Final Adjustments
Adjust the tilt, swivel, and rotation of the monitor arms and VESA plates to your preferred viewing angles. Ensure all connections are secure.
Diagram description: Shows the dual monitor and laptop setup. Arrows indicate adjustment ranges for tilt (+35° to -35°), swivel (±90°), and rotation (±90°).
Step 10: Final Setup Overview
The WALI GSDM003LP allows for flexible positioning of two monitors and a laptop, supporting screens up to 32 inches and laptops up to 17.3 inches. It offers extensive adjustability for ergonomic viewing.
