WALI Heavy-Duty Monitor Arm GSM001XL Installation Guide

Safety Precautions and Warnings

CAUTION: Using products heavier than the indicated rated weights may result in instability and potential injury.
Follow assembly instructions closely. Improper installation can lead to damage or serious personal injury.
Use safety gear and appropriate tools. Professional installation is recommended.
Ensure the supporting surface can safely bear the combined weight of the equipment and all attached hardware.
Use provided mounting screws and do not overtighten.
This product contains small parts that are a choking hazard if swallowed. Keep away from children.
This product is for indoor use only. Outdoor use may cause product failure or personal injury.

Parts Included

Please verify all parts are present before installation. Contact your place of purchase if any parts are missing or faulty.

Component A: Monitor Plate
Component B: Monitor Arm
Component C: Upper Clamp Base
Component D: Lower Clamp Base
Component E: Gas Spring Arm
Component F: Desk Clamp Screw
Component G: Grommet Base
Component H: Grommet Screw
Component I: Allen Key (3mm)
Component J: Allen Key (6mm)
Screws: M-A (M4x12), M-B (M4x16), M-C (M5x12), M-D (M5x16), M-E (M5x12), M-F (M5x16)

Installation Instructions

Step 1: Base Installation (Clamp or Grommet)

Clamp Installation:

Attach the Upper Clamp Base (C) to the desk edge (10-45mm thickness) using the Lower Clamp Base (D) and Desk Clamp Screw (F).

Grommet Installation:

For desks with a through-hole (Ø10-60mm), insert the Grommet Base (G) through the hole and secure it with the Grommet Screw (H).

Step 2: Attach Arm to Base

Connect the Monitor Arm (B) to the installed base using screws M-A and M-E.

Step 3: Attach Monitor Plate to Monitor

Secure the Monitor Plate (A) to the back of your monitor using screws M-B and M-D. Ensure the correct screw length is used to avoid damage.

Step 4: Mount Monitor to Arm

Lift the monitor and attach it to the Monitor Arm (B). Use screws M-C and M-F to secure the monitor to the arm.

Step 5: Final Securing

Ensure the monitor is firmly attached to the arm.

Adjustments

Step 6: Spring Tension Adjustment

To properly balance the arm with the mounted monitor, adjust the spring tension using the 6mm Allen Key (J).

First, position and firmly hold the arm horizontally. If the arm drops, turn the adjustment screw counter-clockwise until it stays horizontal. If the arm rises, turn the adjustment screw clockwise until it stays horizontal.

CAUTION: To avoid damage to the monitor or mount, always keep the arm in a horizontal position while making adjustments.

Step 7: Tilt and Swivel

The arm allows for tilt and swivel adjustments to position your monitor.

Step 8: Rotation

The arm can rotate 180° (±90°) or rotate without stopping (±180°).

Step 9: Limiting Screw

If the display does not stop at your desired position, tighten the limiting screw (do not overtighten) to set a stopping point. Remove or loosen the limiting screw if full rotation is desired.

Step 10: Cable Management

Route cables neatly along the arm for a clean setup.

Maintenance

Periodically check that the arm is secure and safe to use at regular intervals (at least every three months).

	WALI GSMP002 Dual Monitor Desk Mount Installation Manual Step-by-step installation guide for the WALI GSMP002 dual monitor desk mount, covering clamp and grommet installation, VESA plate attachment, and gas spring tension adjustment. Includes safety warnings and part identification.
	WALI GSM001XL-P Heavy-Duty Monitor Arm Installation Guide Comprehensive installation guide for the WALI GSM001XL-P Heavy-Duty Monitor Arm. Includes parts list, step-by-step assembly instructions, and mounting tips for desks and grommets.
	WALI Triple Monitor Desk Mount Installation Manual (GSDM003) Comprehensive installation manual for the WALI GSDM003 Triple Monitor Desk Mount, featuring a premium gas spring arm for screens up to 27 inches. Includes detailed steps for clamp and grommet base installation, monitor attachment, and angle adjustments.
	WALI GSMP001 Single Monitor Desk Mount Installation Guide Comprehensive installation manual for the WALI GSMP001 Single Monitor Desk Mount. This guide provides step-by-step instructions for setting up the monitor arm, including clamp and grommet mounting options, VESA plate attachment, and tension adjustments. Supports monitors up to 32 inches and 9kg.
	WALI GSM002XL Dual Monitor Desk Mount Installation Guide Comprehensive installation guide for the WALI GSM002XL Dual Monitor Desk Mount, detailing clamp and grommet installation, arm attachment, VESA plate mounting, gas spring tension adjustment, and cable management for optimal monitor setup.
	WALI GSDM003LP Monitor Desk Mount Installation Guide Comprehensive installation guide for the WALI GSDM003LP dual monitor and laptop desk mount. Features VESA compatibility, adjustable arms, and detailed assembly steps for safe and ergonomic setup.
	WALI Dual Monitor Desk Mount Installation Manual (M002/M002-W) Comprehensive installation guide for the WALI Dual Monitor Desk Mount (M002/M002-W), featuring step-by-step instructions, safety warnings, and parts list for mounting two monitors up to 27 inches.
	WALI GSAM001 Single Gas Spring Monitor Arm Installation Guide Comprehensive guide for installing and using the WALI GSAM001 Single Gas Spring Monitor Arm. Includes parts list, step-by-step instructions, and adjustment details for optimal monitor positioning.