WALI Dual Monitor Desk Mount

Warnings

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. WALI cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

⚠️ TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.

TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

• Base (A) x1
• Arm (B) x2
• Arm (C) x2
• VESA Plate (D) x2
• Support Plate (E) x1
• Bottom Grommet Plate (F) x1
• Anti-skid Pad (G) x1
• Decor Cover (H) x1
• C-Clamp Brace (I) x1
• C-Clamp (J) x1
• Bolt (K) x4
• Allen Key 3mm (L) x1
• Allen Key 4mm (M) x1
• Allen Key 6mm (N) x1
• M4x12 Bolt (M-A) x8
• M5x12 Bolt (M-B) x8
• D5 Washer (M-C) x8

Installation Instructions

Step 1: Measure Mounting Surface

Measure the thickness of your mounting surface or desk.

Fit clamp: 0.4"-3.3" [clamp-fit]

Grommet: 0.4"-1.9" [grommet-fit]

Step 2: Base Installation

Option A: Clamp Installation

1. Connect the C-Clamp Brace (I) to the Base (A) from the bottom using 4 pcs Bolt (K) and tighten with Allen Key 4mm (M). Tear off the protective paper to attach Anti-Skid Pad (G) to the bottom designated position of Base (A) as shown in the diagram.

Diagram: Shows Base (A), C-Clamp Brace (I), Bolt (K), Allen Key (M), and Anti-skid Pad (G) being assembled.

2. Loosen the Bolts on the C-Clamp (J) using Allen Key 4mm (M). Leave a 6mm gap [gap-indicator].

Diagram: Shows C-Clamp (J) with bolts being loosened by Allen Key (M).

3. Hang the C-Clamp (J) on the C-Clamp Brace (I) to the preferred height according to your desk thickness and tighten using Allen Key 4mm (M). Place Support Plate (E) on top of clamp bolts.

Diagram: Shows C-Clamp (J) being attached to C-Clamp Brace (I) at adjustable height, with Support Plate (E) placed on bolts. Indicates desk thickness ranges: 0.4"-2.3" or 2.0"-3.3".

4. Position base on desktop and tighten clamp bolts evenly using Allen Key 6mm (N). Attach Decor Cover (H) to the back of C-Clamp Brace (I).

Diagram: Shows the assembled clamp base on a desk, being tightened with Allen Key (N), and the Decor Cover (H) being attached.

Option B: Grommet Base Installation

1. Connect the Bottom Grommet Plate (F) to the Base (A) from the bottom using 4 pcs Bolt (K) and tighten with Allen Key 4mm (M). Tear off the protective paper to attach Anti-Skid Pad (G) to the bottom designated position of Base (A) as shown in the diagram.

Diagram: Shows Bottom Grommet Plate (F) being attached to Base (A) with Bolt (K) and Allen Key (M), and Anti-skid Pad (G).

2. Remove clamp bolt from C-Clamp (J) using Allen Key 6mm (N). Place the Base (A) onto the desk hole, and guide the Support Plate (E) through the bolt. Tighten the bolt to the base for stability using Allen Key 6mm (N).

Diagram: Shows C-Clamp (J) bolt removal, Base (A) placement in a desk hole, and Support Plate (E) insertion, secured by Allen Key (N).

Step 3: Connect Arm to Base

Connect the Arm (B) to the Base (A) and tighten the lower screw with Allen Key 3mm (L).

Diagram: Shows Arm (B) being attached to Base (A) and tightened with Allen Key (L).

Step 4: Connect Arms

Connect the Arm (C) to the Arm (B) and tighten with Allen Key 3mm (L).

Diagram: Shows Arm (C) being attached to Arm (B) and tightened with Allen Key (L).

Step 5: Attach VESA Plate to Monitor

Step 5.1: Select Correct Screws

Hand thread screws into the threaded inserts on the back of your TV/Monitor to determine which screw diameter (M4) or (M5) to use.

Diagram: Shows M4x12 and M5x12 screws and how to test them on a monitor's VESA mounting holes.

Step 5.2: Mount VESA Plate

Select M4x12 Bolt (M-A) or M5x12 Bolt (M-B) according to your TV/Monitor. Connect VESA Plate (D) together with D5 Washer (M-C) into the mounting holes on the back of TV/Monitor. Tighten with a screwdriver (not included).

Diagram: Shows VESA Plate (D) being attached to a monitor using Bolts (M-A or M-B) and Washers (M-C).

Step 6: Mount Monitor to Arm

Pull the buckle and put the assembled TV/Monitor onto the Arm (C) and ensure stability.

Diagram: Shows a monitor being attached to the arm by engaging a quick-release buckle.

Step 7: Adjust Gas Spring Tension

Press the Arm (C) on a horizontal level as shown in the image. Adjust gas spring tension to your personal preference using Allen Key 6mm (N).

Adjust the Gas Spring Tension:

• Insert the 6mm Allen Key (N) into the adjusting hole and turn clockwise (-) to reduce gas spring tension, suitable for lighter screens.
• Insert the 6mm Allen Key (N) into the adjusting hole and turn counter-clockwise (+) to increase gas spring tension, suitable for heavier screens.
• Please note it may take numerous turns for gas spring tension adjustment.

Diagram: Shows Allen Key (N) being used to adjust gas spring tension with indicators for clockwise (-) and counter-clockwise (+) turns. Also shows indicators for "For Heavier Monitors" and "For Lighter Monitors".

Step 8: Adjust Tilt Tension

Adjust the tilt tension using Allen Key 6mm (N).

Diagram: Shows Allen Key (N) being used to adjust tilt tension.

Step 9: Cable Management

Screw out the bolts and take off the cable cases.

Diagram: Shows bolts being removed from cable covers.

Step 10: Route Cables

Guide the cables through and put the cable cases back.

Diagram: Shows cables being routed through the arm and cable covers being reattached.

Step 11: Safety Check

For safety, please do not extend the monitor behind the desk. This may cause instability and tip the desk over.

Diagram: Shows correct monitor positioning (checkmarks ✔️) and incorrect positioning (crosses ❌) relative to the desk edge.

Step 12: Final Adjustments

Manually swivel, tilt, and rotate the monitor for the best viewing angle. Store the Allen Keys (L, M, N) in the holder of Decor Cover (H) for future convenience.

Diagram: Shows monitor adjustments (swivel ±180°, tilt ±45°, rotation ±90°, arm tilt ±135°) and Allen Keys being stored in Decor Cover (H).