WALI Triple Monitor Desk Mount Installation Manual

Product Information

Model: GSDM003

VESA Mounting Compatibility: 75x75/100x100 mm

Maximum Monitor Size: 27 inches

Weight Capacity: 1.5-7 kg (3.3-15.4 lbs) per arm

Contact: support@walielectric.com

Important Warnings

WARNING!

Read all instructions before installation. If unsure, contact a qualified technician. Ensure all parts are present and undamaged. Improper installation can lead to damage or serious injury. Do not exceed weight capacity. WALI is not liable for damage or injury from improper mounting, assembly, or use.

TIPOVER WARNING

Serious or fatal crushing injuries can occur from tipover. To prevent tipover:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

Tipover restraints may reduce, but not eliminate, the risk of tipover.

Small parts: Not for children under 3 years. Adult supervision is required.

Supplied Parts List

• Arm A (x1)
• Monitor Arm B (x1)
• VESA Plate C (x3)
• C-Clamp D (x1)
• Pole E (x1)
• Wire Clip F (x1)
• Grommet Base Plate G (x1)
• Support Plate H (x1)
• Anti-skid Pad I (x1)
• Top Screw J (x3)
• M6x16 Bolt K (x3)
• 4mm Allen Key L (x1)
• 6mm Allen Key M (x1)
• M4x12 Bolt M-A (x12)
• M4x16 Bolt M-B (x12)
• M5x12 Bolt M-C (x12)
• M5x16 Bolt M-D (x12)
• D5 Washer M-E (x12)
• Spacer M-F (x12)

Step 1: Measure Mounting Surface

Measure the thickness of your mounting surface or desk.

Clamp Fit: 0.4" - 3.3"

Grommet Fit: 0.4" - 1.6"

Step 2: Mount Installation

Option A: Clamp Installation

1. Loosen bolts on C-clamp using 4mm Allen Key L.
2. Connect Pole E and C-clamp Brace D1 using M6x16 Bolt K and tighten with 4mm Allen Key L. Tear off protective paper and attach Anti-Skid Pad I to the bottom of C-Clamp Brace D1.
3. For 0.4"-2" thick desks: Hang C-Clamp D on the bolts and tighten using 4mm Allen Key L.
4. For 1.8"-3.3" thick desks: Loosen the screw to release the hand knob using a screwdriver. Turn over the bracket and tighten the screw. Loosen bolts on C-Clamp Brace D1 using 4mm Allen Key L. Hang C-Clamp D on the bolts and tighten using 4mm Allen Key L.
5. Rotate the hand knob clockwise to fasten for stability.

Option B: Grommet Base Installation

1. Cut Anti-skid Pad I along the broken line. Tear off protective paper and attach to the bottom of Grommet Base Plate G.
2. Loosen the screw to release the hand knob (screwdriver not included).
3. Existing Grommet Hole Installation: If the hole has a plastic protector, remove it for a flat surface.
4. Self-drilled Grommet Hole Installation: Drill a 3/8" (10mm) diameter hole at the marked position.
5. Place Grommet Base Plate G and Pole E into the grommet hole. Insert hand knob through the center hole of Support Plate H and desk hole. Rotate hand knob clockwise to fasten for stability.

Step 3: Spring Arm Release

WARNING: Firmly hold the two halves of the spring arm together. Have another person cut the cable tie around the spring arm. Slowly release pressure on the spring arm to allow it to stretch to its full extension.

Step 4: Attach Arms to Pole

Insert Arm A and Monitor Arm B through Pole E. Adjust height and tighten using 6mm Allen Key M. Attach Wire Clip F to Pole E.

Step 5: Attach Monitor to VESA Plate

Step 5.1: Select Monitor Screws

Use M4 or M5 screws. Hand thread screws into the monitor's threaded inserts to determine the correct diameter.

Step 5.2: Select Spacers (if needed)

Spacers are needed for monitors with inset holes or round monitors.

Step 5.3a: For Flat Monitors (No Inset Holes)

Select M4x12 Bolt M-A or M5x12 Bolt M-C. Connect VESA Plate C with D5 Washer M-E to the monitor's mounting holes using a screwdriver (not included).

Step 5.3b: For Monitors with Inset Holes or Round Monitors

Select M4x16 Bolt M-B or M5x16 Bolt M-D. Connect VESA Plate C with D5 Washer M-E and Spacer M-F to the monitor's mounting holes using a screwdriver (not included).

Step 6: Mount Monitor to Arm

Place the assembled TV/Monitor onto Arms A and B. Ensure stability and tighten the VESA plate using Top Screw J.

Step 7: Balance Arm Tension

Adjust spring tension with 6mm Allen Key M to balance the arm horizontally. Hold the arm horizontally and ask for assistance if needed.

• If the arm drops: Turn the adjustment screw counter-clockwise until horizontal.
• If the arm rises: Turn the adjustment screw clockwise until horizontal.

CAUTION: To avoid damage, always keep the arm horizontal during adjustments. Do not overtighten screws.

Step 8: Cable Management

Slide cable slot covers towards the VESA plate to detach. Guide cables through the slots and reattach the covers.

Step 9: Angle Adjustments

• Tilt: Adjust VESA Plate tilt using 6mm Allen Key M. (Tilt +35°/-35°). If the display doesn't hold position, tighten screws.
• Swivel: Manually adjust swivel angle (-90°/+90°).
• Rotate: Manually adjust rotate angle (360°).

Store Allen Keys L and M in the Wire Clip F.

Conclusion

Thank you for choosing WALI! We support technology that enhances your home. We offer high-quality products, professional customer service, and extensive technical support.

For questions, please contact WALI:

Phone: 1-844-SATTLER (18447288537)

Email: support@walielectric.com

Website: www.walielectric.com