SaunaLife LED Lightbar System

LED Lightbar Package Contents:

• RF Driver / Receiver (qty. 1)
• Power Supply (qty. 1)
• Dimming Remote (qty. 1)
• 2-Pin 4-Way Cable (qty. 1)
• 2-Pin 30' Cable (qty. 1)
• AC Power Cable (qty. 1)
• Adjustable Mounting Clips (qty. 3)
• Stationary Mounting Clips (qty. 3)
• White Led Light Bar (qty. 1)

Installation Recommendations

Please read this manual in its entirety prior to installation and keep it somewhere safe for future reference.

IMPORTANT:

• The RF Driver and Power Supply may be installed outdoors but must be protected from rain and snow. RF Driver and Power Supply should be installed in a waterproof electrical enclosure.
• When installing the RF Driver and Power Supply inside the sauna, maintain a minimum distance of 20 inches from heat source and a maximum height of 20 inches off floor or in path of fan.
• If installed inside the sauna, the RF Control must not exceed 131°F. Control should be no more than 3' off the floor and away from heater. Test temperature reading of location before mounting.
• Consider light placement carefully. Each fixture should be placed to avoid direct contact with the bather's eyes.
• LED Light Bar max operating temperature is 195°F; installing LED light bar in a location where temperature will exceed 195°F may cause light failure.

Electrical Requirements

! A 120V AC electrical outlet is needed to power the lighting system.

• Your electrician will determine the type of electrical outlet, box, and piping to be used.
• All wiring must be done in accordance with national electric code and local building codes by a certified electrician.
• Improper voltage or connections will damage the components and void warranty.

STEP 1. Mount RF Driver / Receiver

Using 2 screws, mount RF driver to desired surface. Driver should be mounted in a dry accessible location for service.

[Image: Person holding a small white mounting bracket for the RF driver.]

[Image: Person using a drill to attach the RF driver mounting bracket to a wooden surface with screws.]

[Image: Person using a drill to screw the RF driver onto the mounted bracket.]

STEP 2. Connect 2-Pin 4-Way Cable

Locate 2-Pin 4-way cable and connect the single end to the 2-Pin Pigtail of the Driver.

[Image: Person connecting the single 2-pin end of the 2-Pin 4-Way Cable to the RF Driver.]

[Image: Close-up of the connection being made.]

STEP 3. Run 2-Pin 30' Cable

Run the 2-Pin 30' light cable from the Driver to the LED light bar. At the Driver, connect to one of the 4 leads on the 2-Pin 4-Way cable.

[Image: Person running the 2-Pin 30' Cable along a wooden surface.]

[Image: Person connecting the 2-Pin 30' Cable to one of the four outputs on the 2-Pin 4-Way Cable connected to the RF Driver.]

STEP 4. Install Mounting Brackets & LED Light Bar

Determine the location where the LED light will be installed. Screw Mounting Clips to the surface, ensuring even coverage of the light fixture. Carefully snap the LED light bar into each clip.

[Image: Person using a drill to screw a mounting clip onto a wooden panel.]

[Image: Person snapping the LED light bar into a mounted clip.]

[Image: Person holding a long LED light bar, showing its slim profile.]

STEP 5. Connect 2-Pin 30' Cable to Light Bar

Connect the light cable end to the lead off the light bar.

Note: Repeat this step if installing more than one light.

[Image: Person connecting the end of the 2-Pin 30' Cable to the LED light bar.]

[Image: Close-up of the connection between the cable and the light bar.]

STEP 6. Install Power Supply

Connect the AC power cord cable to the power supply block. Place the power supply near the RF driver. Connect the DC cable end from the power supply and connect it into the RF driver DC IN port.

[Image: Person connecting the AC power cord to the Power Supply block.]

[Image: Person connecting the DC output cable from the Power Supply to the RF Driver's DC IN port.]

[Image: A view showing the Power Supply connected to the RF Driver, with multiple cables attached.]

STEP 7. Dimming Control Installation

The RF Remote includes a wall mount holder for storing. Take the holder and separate the back mounting plate from the holder. At the mounting location, screw the mounting plate to the surface. Slide the holder from top down onto the mounting plate.

[Image: Person measuring a spot on a wooden wall with a tape measure.]

[Image: Person drilling pilot holes for the remote holder mounting plate.]

[Image: Person attaching the remote holder mounting plate to the wall.]

[Image: Person sliding the remote holder onto the mounted plate.]

STEP 8. Startup & Testing

• Verify that all connections are secure and complete before proceeding.
• Ensure the DC-out end of the Power Supply is plugged into the DC-in of the Driver.
• Plug the AC power cable from the Power Supply into a 120V AC electrical outlet.
• Verify that the Driver powers on. The indicator light will flash purple rapidly for approximately 20 seconds.

STEP 9. RF Driver & Dimming Remote Programming

Note: RF Driver is preprogrammed. Follow steps below if programming is needed.

1. Press and hold the Match button until the Run Indicator light changes to white.
2. Note: The Run indicator will turn off, then rapidly flash purple. White run indicator will be after Blue.
3. Release the Match button, then short press once to save programming.
4. Grab remote, then on Driver press match button once, then quickly press the power button on remote.

Control Operation

Follow the steps below for control operation. After 30 seconds of inactivity, the remote will enter sleep mode. To wake up the control, press any button.

[Diagram: A visual representation of the dimming remote, showing the 'On / Off' button, 'Brightness Control' slider (marked 1%, 50%, 100%), and 'LED Indicator' light.]

Wi-Fi Setup

On iOS or Android, download the Tuya Smart App.

To set up Wi-Fi operation, follow the steps below.

Note: Wi-Fi Driver supports 802.11 b/g/n 2.4 GHz Wi-Fi standard.

Step 1: Open Tuya app and press Sign Up to create an account.

[Image: Tuya app login/signup screen.]

Step 2: Enter an email address to register an account.

[Image: Tuya app email registration screen.]

Step 3: Check email and enter verification code.

[Image: Tuya app verification code entry screen.]

Step 4: Create a password.

[Image: Tuya app password creation screen.]

Step 5: Main screen, press 'Add Device'.

[Image: Tuya app main screen with 'Add Device' button.]

Step 6: Press 'Add' next to 'Discovering Devices'.

[Image: Tuya app 'Discovering Devices' screen with 'Add' button.]

Step 7: Select your Wi-Fi network and enter password.

[Image: Tuya app Wi-Fi network selection screen.]

Step 9: Device added successfully, press 'Done' to complete setup.

[Image: Tuya app 'Device added successfully' confirmation.]

Specifications

RF Driver/Receiver

Power Supply

RF Remote Single-Zone Dimming

LED Light Bar Specifications

Troubleshooting

No Power

• Verify that the electrical outlet has voltage.
• Check that connections on Power Supply are securely connected.
• Check that the DC barrel plug on the Power Supply is securely connected.

Power but light's not turning on

• Check that the Pigtail cable from the Driver is securely connected and that wiring is correct (see step #1).
• Check that 4-way light cable is secure and connected.
• Check that all 30' cables to lights are securely connected.
• Verify each light functions by testing them directly to the Driver independently. Note: To test individual light, disconnect 4-way light cable and connect 30' cable directly to Pigtail lead of Driver, or connect light directly Pigtail.
• Verify that RF Remote is paired with Driver, see page #7.

Lights on with no function from Control

• Verify battery is inserted correctly.
• Low battery, replace with new battery.
• Check DC power cable from Driver to Control is securely connected.
• Ensure that the distance from the Remote to the Driver is not more than 98 feet. If so, relocate Driver closer to room.

Resetting Driver

The Driver should not need to be reset in normal conditions. If a reset is needed, follow the steps below.

• Verify power to Driver.
• Press and hold the Match button for 10-15 seconds until the blue LED indicator flashes rapidly. Note: Resetting Driver will clear any paired remotes and require repairing.

Replacement Parts

Notes:

[Blank lines for notes]