Assembly Instructions
43150731 SLATTED STORAGE CABINET
Care Instructions
Wipe clean with a dry cloth. Do not use abrasive materials and solvents. Check and tighten all parts regularly. Do not place hot items such as coffee cups directly on the surface. Keep away from water and direct sunlight. Store in a dry place. For domestic use only. For indoor use only. A mild odour may be present when first opening this carton; simply allow to air outside and this will fade.
Warnings
- ⚠️ DO NOT stand or sit on this unit.
- ⚠️ DO NOT use this unit unless all bolts and screws are firmly secured.
- ⚠️ DO NOT knock or drag this unit.
- Use only on a flat surface.
- Adult assembly required.
- Failure to follow these warnings could result in serious injury.
- Load drawer evenly to prevent from tipping over.
- This package contains small parts and sharp points. Keep away from children and babies.
Maximum Safe Load: 15KG for top, 10KG for each layer.
Hardware List
| Ref | Description | Quantity |
|---|---|---|
| A | 6x30mm screw | 12pcs |
| B | 6x35mm screw | 10pcs |
| C | 12x10mm screw | 10pcs |
| D | Screw | 4pcs |
| E | 3x18mm screw | 12pcs |
| F | 100x20x15mm component | 2pcs |
| G | 4x35mm screw | 4pcs |
| H | 4x40mm screw | 6pcs |
| I | 3x12mm screw | 10pcs |
| J | Screw | 8pcs |
| K | Component | 2pcs |
| L | Component | 4pcs |
| M | Component | 2pcs |
| N | Component | 2pcs |
| O | 3x14mm screw | 4pcs |
| P | 7x50mm screw | 6pcs |
| Q | Component | 1pc |
Parts List
| Ref | Description | Quantity |
|---|---|---|
| 1 | Base Panel | 1pc |
| 2 | Side Panel | 1pc |
| 3 | Side Panel | 1pc |
| 4 | Shelf | 1pc |
| 5 | Top Panel | 1pc |
| 6 | Back Panel | 1pc |
| 7 | Support Panel | 1pc |
| 8 | Back Panel | 1pc |
| 9 | Foot/Base Support | 4pcs |
| 10 | Door | 2pcs |
Step 1
Attach the two Side Panels (2 and 3) to the Base Panel (1) using screws A (x4), screws B (x4), and screws C (x4). Ensure the panels are aligned correctly with the pre-drilled holes.
[Diagram shows side panels being attached vertically to the base panel, with screws inserted from the outside into the edges of the base panel.]
Step 2
Slide the Back Panel (6) into the grooves on the back of the side panels. Insert the Shelf (4) between the side panels, aligning it with the designated slots or holes.
[Diagram shows the back panel being slid into place and the shelf being positioned horizontally between the side panels.]
Step 3
Attach the Top Panel (5) to the top edges of the Side Panels (2 and 3) using screws B (x6) and screws O (x2). Also, attach the Component N (x1) to the top panel for adjustable positioning.
[Diagram shows the top panel being placed on the side panels and secured with screws. Component N is shown being attached to the underside of the top panel.]
Step 4
Attach the second Side Panel (2) to the Base Panel (1) and Top Panel (5) using screws A (x4) and screws C (x6). Ensure the Back Panel (6) is correctly positioned.
[Diagram shows the second side panel being attached to the assembly, securing the top and base panels. Screws A and C are shown being inserted.]
Step 5
Insert the Shelf (4) into the cabinet. Attach the Support Panels (7) to the inside of the side panels using screws H (x4).
[Diagram shows screws H being used to attach the shelf and support panels to the side panels.]
Step 6
Attach the Top Panel (5) again, securing it with Component N (x1) and screws O (x2). This step might be for reinforcing the top or for a specific configuration.
[Diagram shows the top panel being secured with components N and screws O.]
Step 7
Attach the Doors (10) to the cabinet frame. Use screws D (x4), screws E (x12), components F (x2), and screws G (x4) for this process. The diagram shows how the hinges are mounted.
[Diagram shows the doors being attached to the front of the cabinet. Screws E are used for hinges, and screws D and G secure other parts. Component F is also shown.]
Step 8
Secure the Top Panel (5) to the main cabinet structure using screws A (x4).
[Diagram shows screws A being inserted into the top panel to secure it to the side panels.]
Step 9
The main cabinet structure is now assembled. The doors (10) are attached to the front.
[Diagram shows the assembled cabinet with doors closed.]
Step 10
Attach the Back Panels (5) to the rear of the cabinet using screws P (x6). Attach the Component Q (x1) to the top front edge, likely as a decorative trim.
[Diagram shows screws P securing the back panels and component Q being attached to the top.]
Step 11
Attach the Feet/Base Supports (9) to the underside of the cabinet using screws I (x2), screws K (x2), and screws L (x2).
[Diagram shows the base supports being screwed into the bottom of the cabinet.]
Step 12
Attach the remaining Feet/Base Supports (9) to the underside of the cabinet using screws I (x8) and screws J (x8).
[Diagram shows more screws I and J being used to attach the base supports.]
Step 13
Attach the Top Panel (5) and secure the unit to the wall using screws H (x2), screws L (x2), and screws M (x2). Follow the detailed warnings and cautions regarding wall mounting.
[Diagram shows the final assembly and details for wall mounting, including screws H, L, M being used with wall anchors.]
Toppling Furniture Warning
- It is strongly recommended that this product is permanently fixed to the wall.
- Please seek professional advice if you are in doubt of what fixing device to use.
- Regularly check that anchors are securely maintained.
- Stability of tall items may be affected by thick pile carpet or uneven floors.
- Do not place unanchored televisions on furniture.
CAUTION:
For your safety when attaching the anchor fixings, please note the following:
- Check any electrical wires or plumbing inside the wall before drilling any holes (if you are unsure please seek professional advice from a qualified tradesperson).
WARNING: PLEASE SECURE YOUR FURNITURE WITH THE SUPPLIED WALL FIXING. [QR Code for more information]
