Fellowes POWERSHRED 79Ci

Shredder Overview

A front-view photograph of the Fellowes Powershred 79Ci shredder shows its modern design with a dark grey body and silver accents. The paper entry slot is at the top, a pull-out bin is integrated into the base, and casters are present at the bottom.

Key Components

• A. SafeSense® Technology: [safety sensor]
• B. Paper entry: [paper slot]
• C. See safety instructions: [safety icon]
• D. CD/Card safety flap: [CD/Card flap]
• E. Pullout bin: [waste bin]
• F. Casters: [wheels]
• G. Disconnect power switch: (1. OFF ⚫, 2. ON ▶️)
• H. Control Panel and LEDs:
  • 1. Overheat: ? Overheat
  • 2. Bin open: ? Bin open
  • 3. Bin full: ? Bin full
  • 4. Remove Paper: ? Remove Paper
  • 5. SafeSense® indicator: ? SafeSense® indicator
  • 6. Sheet capacity indicator: [sheet capacity indicator]
  • 7. Auto: ? Auto
  • 8. Reverse: ? Reverse
  • 9. ON/OFF: ? ON/OFF
  • 10. Forward: ▶️ Forward

Capabilities & Specifications

Will shred: Paper, credit cards, CD/DVDs, staples, and small paper clips.

Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard, large paper clips, laminates, file folders, X-rays, or plastic other than noted above.

Paper shred size: Cross-Cut: 5/32" x 1-1/2" (3.9 x 38mm)

Maximums:

• Sheets per pass: 14*
• CDs/Cards per pass: 1*
• Paper entry width: 9" (230mm)

*Capacity based on 8.5"x11", 20lb. (75g) paper at 120V, 60 Hz, 4Amps. Heavier paper, humidity, or voltage variations may reduce capacity.

Recommended daily usage: 500 sheets, 25 credit cards, 10 CDs.

Operating Environment: Designed for home and office environments ranging between 50-80°F (10-26°C) and 40-80% relative humidity.

Important Safety Instructions

• Keep away from children and pets. Keep hands away from paper entry. Always set the power switch to OFF (⚫) or unplug when not in use.
• Keep foreign objects (gloves, jewelry, clothing, hair, etc.) away from shredder openings. If an object enters the top opening, switch to Reverse (?) to back out the object.
• Never use aerosol products, petroleum-based lubricants, or other flammable products on or near the shredder. Do not use canned air on the shredder.
• Do not use if damaged or defective. Do not disassemble the shredder.
• Do not place near or over a heat source or water.
• Operation, maintenance, and service requirements are covered in the instruction manual. Read the entire manual before operating.
• The Disconnect Power Switch (G) must be in the ON (▶️) position to operate. In case of emergency, move the switch to OFF (⚫) to stop the shredder immediately.
• Avoid touching exposed cutting blades under the shredder head.
• Plug into a properly grounded wall outlet or socket of the designated voltage and amperage. The outlet must be easily accessible. Do not use energy converters, transformers, or extension cords.
• FIRE HAZARD: Do NOT shred greeting cards with sound chips or batteries.
• For indoor use only.

FCC Compliance: This equipment complies with Part 15 of the FCC Rules for Class B digital devices, designed to provide reasonable protection against harmful interference in residential installations. If interference occurs, try reorienting the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician.

Basic Setup: Caster Installation

Follow these steps to install the casters:

1. Unpack the shredder.
2. Align the casters with the mounting points on the shredder base.
3. Push casters firmly into place until they click.
4. Repeat for all casters.
5. Ensure all casters are securely attached.

Basic Shredding Operation

Continuous operation: 12-minute maximum. The shredder runs briefly after each pass to clear the entry. Continuous operation beyond 12 minutes triggers a 20-minute cool-down period.

Steps:

1. Plug in the shredder and set the disconnect power switch (G) to ON (▶️).
2. Press the ON/OFF button (9) to activate the shredder (blue light ?).
3. Feed paper straight into the paper entry (B) and release.
4. To shred CDs or credit cards, rotate the safety flap (D) into place.
5. Hold cards/CDs at the edge and feed into the center of the entry and release.
6. When finished shredding, set the disconnect power switch (G) to OFF (⚫).

Advanced Product Features

100% Jam Proof System

Eliminates paper jams and powers through tough jobs. Advanced Jam Prevention electronically measures paper thickness to prevent jams:

• ? RED: Too many sheets inserted.
• ? YELLOW: Productivity optimized.
• ? GREEN: More sheets can be added.

If a misfeed occurs: All indicators light up, and the shredder pauses for 3-6 seconds. Remove several sheets until the indicator is below red. Wait for flashing to stop after automatic correction; regular shredding will resume. (100% Jam Proof when used in accordance with the user manual).

SafeSense® Technology

Stops shredding immediately when hands touch the paper opening.

Set-up and Testing:

1. Turn the shredder ON (▶️) to activate SafeSense®.
2. Touch the test area near the paper entry and look for the SafeSense® indicator (?) to illuminate.
3. SafeSense® is active and working properly.

If the indicator illuminates after paper has been reversed, press reverse (?) and remove paper. Otherwise, regular shredding will resume.

SilentShred™ Technology

Provides quiet shredding without noisy disruptions.

Product Maintenance

Oiling Shredder

Cross-cut shredders require oil for peak performance. Oiling prevents diminished sheet capacity, intrusive noise, and potential shutdown. Fellowes recommends oiling each time the waste bin is emptied.

Oiling Procedure (Repeat twice):

1. Apply oil across the paper entry (B).
2. Press and hold the forward (▶️) button for 2-3 seconds.

CAUTION: Only use a non-aerosol vegetable oil in a long nozzle container, such as Fellowes 35250.

Cleaning Auto-Start Infrared Sensors

Paper detection sensors may become blocked by paper dust, causing the motor to run even if no paper is present. (Two sensors are located in the center of the paper entry).

To Clean the Sensors:

1. Turn off and unplug the shredder.
2. Locate the auto-start infrared sensors in the paper entry.
3. Dip a cotton swab in rubbing alcohol.
4. Using the cotton swab, wipe away any contamination from the paper sensors.

Troubleshooting

Indicator Lights

• A. Overheat Indicator (?): Shredder has exceeded maximum operating temperature and needs to cool down. Shredder will not operate until cool.
• B. Bin Open (?): Shredder will not run if the bin is open. Close the bin to resume.
• C. Bin Full (?): Waste bin is full and needs emptying. Use Fellowes waste bag 36052.
• D. Remove Paper (?): Press reverse (?) and remove paper. Reduce paper quantity and refeed.
• E. SafeSense® Indicator (?): Hands are too close to the paper entry. Shredder stops. If SafeSense® is active for 3 seconds, it automatically turns off. Press the power button to resume.

Jam Proof System Disabling

To disable: Press and hold the Auto button (?) and the Reverse (?) key simultaneously.

Once disabled: The blue Auto light (?) is no longer illuminated. To re-engage, repeat the disabling step.

Shredding can continue with the system disabled, but a paper jam may occur with too many sheets, and the "Remove Paper" icon (?) will illuminate.

If a jam occurs: Press and hold the forward (▶️) key until the document is completely through the shredder.

If not cleared: Press reverse (?) briefly. Repeat steps 4 and 5 until shredded.

If steps 4 and 5 do not clear jam: Reverse paper all the way out, remove several sheets, and refeed.

Limited Product Warranty

Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for the lifetime of the shredder.

If any part is found to be defective during the warranty period, the sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective part.

This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply, or unauthorized repair. Fellowes reserves the right to charge for parts or services outside the country where the shredder was initially sold by an authorized reseller.

Any implied warranty, including that of merchantability or fitness for a particular purpose, is hereby limited in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights.

The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact Fellowes or your dealer.

Contact Information

Website: www.fellowes.com

Customer Service & Support:

• Troubleshooting
• Replacement parts
• General questions

Resources:

• Registration
• Manuals

Customer Service Phone Numbers:

• Canada: +1-800-665-4339
• Mexico: +1-800-234-1185
• United States: +1-800-955-0959

Fellowes, Inc.
1789 Norwood Avenue, Itasca, Illinois 60143-1095 USA
Phone: 630-893-1600

Part No. 406773