Please read these instructions before use. Do not discard: keep for future reference.
Quality Office Products Since 1917
Product Overview
Models: 225Ci/225i
Key Components and Controls
The shredder features the following key components and controls:
- A. SafeSense® Technology: Prevents shredding when hands touch the paper entry.
- B. Paper/card entry: Slot for shredding paper and credit cards.
- C. CD entry: Dedicated slot for shredding CDs/DVDs.
- D. Door: Access to the waste bin.
- E. Basket (paper): Main waste bin for shredded paper.
- F. Basket (CD): Separate bin for shredded CDs.
- G. Casters (4): Wheels for mobility.
- H. Disconnect power switch: Located on the back, with positions for OFF (⚫) and ON (▶️).
- I. Sheet capacity indicator: Visual guide for the number of sheets being fed.
- J. Safety instructions: Reference to safety guidelines.
- K. Shipping bolts (wing nuts): Must be removed prior to operation.
Control Panel and LEDs
The control panel includes the following indicators and functions:
- Power Switch: 1. OFF (⚫), 2. ON (▶️)
- Operation Modes: 3. Forward (▶️), 4. Auto (▶️)
- Indicators: 5. Door open (red ?), 6. Bin full (red ?), 7. Remove paper (red ?), 8. SafeSense® indicator (yellow ?).
Capabilities
Will shred: Paper, credit cards, CD/DVD, staples, and small paper clips.
Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard, large paper clips, folders, X-rays, or plastic other than noted above.
Paper Shred Size:
- Cross-Cut (225Ci): 5/32 inches x 1-1/2 inches (3.9mm x 38mm)
- Strip Cut (225i): 7/32 inches (5.8mm)
Maximum Specifications:
- Sheets per pass: 20*
- CDs/Cards per pass: 1*
- Paper entry width: 9 inches (230mm)
*Based on 8.5"x11", 20lb. (75g) paper at 120V, 60 Hz, 6Amps. Heavier paper, humidity, or other than rated voltage may reduce capacity.
Recommended daily usage rates: 5000 sheets; 200 cards; 10 CDs.
Operating Environment: Fellowes SafeSense® shredders are designed for office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
⚠️ IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
- Keep away from children and pets. Keep hands away from paper entry. Always set the power switch to OFF (⚫) or unplug when not in use.
- Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder openings. If an object enters the top opening, switch to Reverse (◀️) to back out the object.
- Never use aerosol products, petroleum-based lubricants, or other flammable products on or near the shredder. Do not use canned air on the shredder.
- Do not use if damaged or defective. Do not disassemble the shredder. Do not place near or over a heat source or water.
- Operation, maintenance, and service requirements are covered in the instruction manual. Read the entire instruction manual before operating shredders.
- This shredder has a Disconnect Power Switch (H) that must be in the ON (▶️) position to operate. In case of emergency, move the switch to OFF (⚫) position. This action will stop the shredder immediately.
- Avoid touching exposed cutting blades under the shredder head.
- Use only the designated entry for CDs/cards. Keep fingers away from the CD entry.
- Do not put foreign objects in the paper entry.
- The shredder must be plugged into a properly grounded wall outlet or socket of the voltage and amperage designated on the label. The grounded outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be used with this product.
- FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
- For indoor use only.
Basic Shredding Operation
Follow these steps for basic shredding:
- Plug in the shredder and set the disconnect power switch to the ON (▶️) position.
- Press the ON (▶️) button on the control panel to activate the shredder.
- Feed paper or card straight into the paper entry and release. The shredder will automatically start.
- For CDs/cards, hold them at the edge and feed them into the center of the CD entry and release.
- When finished shredding, set the power switch to OFF (⚫).
- Alternatively, if no activity is detected for 2 minutes, the shredder will automatically enter Sleep Mode.
Visit www.fellowes.com for an extensive on-line support section with a number of self-service options.
Advanced Product Features
- 100% Jam Proof System: Eliminates paper jams and powers through tough jobs.
- Patented SafeSense® Technology: Stops shredding immediately when hands touch the paper entry.
- Sleep Mode: An energy-saving feature that shuts down the shredder automatically after 2 minutes of inactivity.
100% Jam Proof System Operation
This system electronically measures paper thickness to prevent paper jams:
- Indicator GREEN: More sheets can be added.
- Indicator YELLOW: Productivity is optimized.
- Indicator RED: Too many sheets have been inserted.
If a misfeed occurs: All indicators will light up, and the shredder will pause for 3-6 seconds. Wait for flashing to stop after automatic correction is complete; regular shredding will resume. If the indicator illuminates after paper has been reversed, press reverse (◀️) and remove paper. Otherwise, regular shredding will resume.
SafeSense® Technology Operation
Stops shredding immediately when hands touch the paper opening.
Set-up and Testing:
- Turn the shredder ON (▶️) to activate SafeSense®.
- Touch the test area and look for the SafeSense® indicator (yellow ?) to illuminate.
- SafeSense® is now active and working properly.
- If a hand is held on the SafeSense® area for more than 2 seconds, the shredder will shut off.
Sleep Mode Operation
Energy saving feature shuts down the shredder after 2 minutes of inactivity.
When in Sleep Mode:
- The shredder is in sleep mode.
- To exit sleep mode, touch the control panel.
- Insert paper to resume operation.
Product Maintenance
Cleaning Auto-Start Infrared Sensors
Paper detection sensors are designed for maintenance-free operation. However, on rare occasions, sensors may become blocked by paper dust, causing the motor to run even if there is no paper present. (Note: two paper detection sensors are located in the center of the paper entry).
To Clean the Sensors:
- Turn off and unplug the shredder.
- Locate the Auto-start infrared sensor.
- Dip a cotton swab (?) in rubbing alcohol (?).
- Using the cotton swab, wipe away any contamination from the paper sensors.
Oiling Shredder
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding, and could ultimately stop running. To avoid these problems, it is recommended to oil the shredder each time the waste bin is emptied.
Follow Oiling Procedure Below and Repeat Twice:
- Apply oil across the entry.
- Press and hold the forward button (▶️) for 2-3 seconds.
CAUTION: Only use a non-aerosol vegetable oil in a long nozzle container, such as Fellowes 35250.
Troubleshooting
The control panel features indicators to help diagnose issues:
- A. Door Open Indicator (red ?): The shredder will not run if the cabinet door is open. When illuminated, close the door to resume shredding.
- B. Bin Full Indicator (red ?): When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054.
- C. Remove Paper Indicator (red ?): When illuminated, press reverse (◀️) and remove paper. Reduce paper quantity to an acceptable amount and refeed into the paper entry.
- D. SafeSense® Indicator (yellow ?): If hands are too close to the paper entry, the SafeSense® indicator will illuminate, and the shredder will stop shredding. If SafeSense® is active for 3 seconds, the shredder will automatically turn off, and the user must press the power button on the control panel to resume shredding.
Self Cleaning Cycle: The shredder periodically cycles in forward and reverse for 3-6 seconds (225Ci model only).
Support and Warranty
For questions or concerns, visit www.fellowes.com.
Support Resources:
- Troubleshooting
- Registration
- Manuals
Customer Service & Support:
- Troubleshooting
- Replacement parts
- General questions
Contact Information:
- Canada: +1-800-665-4339
- Mexico: +1-800-234-1185
- United States: +1-800-955-0959
Limited Product Warranty
Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for the lifetime of the shredder.
If any part is found to be defective during the warranty period, the sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply (other than listed on the label), or unauthorized repair.
Fellowes reserves the right to charge consumers for any additional costs incurred by Fellowes to provide parts or services outside of the country where the shredder is initially sold by an authorized reseller.
Any implied warranty, including that of merchantability or fitness for a particular purpose, is hereby limited in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product.
This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact your dealer or Fellowes.
Fellowes Address: 1789 Norwood Avenue, Itasca, Illinois 60143-1095 USA
Phone: 630-893-1600
©2012 Fellowes, Inc. Part No. 406777
