MIBOXER AC Triac Dimmer (Zigbee 3.0 + 2.4G + Push)

Contents

• 1. Feature
• 2. Parameter
• 3. Connection Diagram
• 4. Installation Diagram
• 5. PUSH Dimming
• 6. Remote Control Instruction
• 7. Smartphone APP Control Instruction
• 8. Philips Hue Control Instruction
• 9. Alexa Voice Control Instruction
• 10. Google Home Voice Control Instruction
• 11. Attention

1. Feature

This AC Triac Dimmer offers a simple, low-cost installation without needing to change the original wire layout. Its mini appearance fits standard EU/USA junction boxes. It is widely applicable for single-color triac LED lights, filament lamps, and halogen lamps.

• Zigbee 3.0 standard protocol
• Smartphone APP control (requires a Zigbee 3.0 gateway)
• 2.4G RF wireless remote control
• Push dimming function
• Trailing edge phase-cut technology
• 0-100% stepless dimming and flicker-free operation
• Lowest brightness setting function
• Built-in temperature detecting switch with overheat/overload protection
• Auto transmitting function for unlimited control distance
• Screw connector for reliable and easy installation
• Anti-fire PC shell for enhanced safety

Various control solutions are supported:

[Philips Hue] [MiBoxer Zigbee Gateway] [IKEA TRÅDFRI] [2.4GHz Remote] [Amazon Echo Plus]

Powered by Tuya

2. Parameter

Model No.: TRI-C1ZR

• Input Voltage: 100-240V~ 50/60Hz
• Output Voltage: 100-240V~
• Output Current: Max 1.36A
• Output Power: 150W @110V; 300W @220V
• Dim Method: Zigbee 3.0 + 2.4G + Push
• Working Temperature: -10~40°C
• Zigbee Control Distance: 100m (open area)
• 2.4G RF Control Distance: 30m

Diagram showing the dimmer's dimensions: 25mm width, 49mm height and 49mm depth. Features include a SET button and an indicator light.

3. Connection Diagram

Input: AC100~240V

Connections: PUSH switch, INPUT (Neutral 'N', Live 'L'), OUTPUT (Neutral 'N', Load 'L1').

Suitable for: Triac dimming LED light, Filament lamps, and Halogen lamps.

⚠️ Attention: Please check and ensure that all cables are correctly connected before turning on the device, otherwise the dimmer may be damaged.

"Breaker mode" activated or shut down

Note: In this mode, the dimmer only supports turning the light ON/OFF; dimming is not possible.

• Turn On: Short press “SET” 5 times quickly. The indicator will blink 3 times quickly.
• Turn Off: Short press “SET” 5 times quickly. The indicator will flash 3 times slowly.

For APP ON/OFF control, review page 13.

4. Installation Diagram

Supports standard junction boxes.

Illustrations showing compatible junction boxes and the PUSH switch installation, noting the required junction box depth is over 50mm.

5. PUSH Dimming

• Short press PUSH switch: Turns the light ON/OFF.
• Long press PUSH switch:
  • Activates stepless dimming brightness.
  • Long press and release your finger, then repeat long pressing to increase or decrease brightness.
  • If multiple dimmers are connected to the same self-return switch, long press the switch for 20 seconds until all lights reach 100% brightness. The quantity of dimmers connected to a single self-return switch should not exceed 25 pieces, and the connection cable length should not exceed 20m.

6. Remote Control Instruction

6.1. Link Remote

For K1 remote

1. Learning code:
   1. Way 1: Short press “SET” once; the indicator will be bursting.
   2. Way 2: Power off the dimmer for 10 seconds and power on again.
   3. Way 3: Short press the Push switch to keep the light ON.
2. Press “SET” 3 times within 3 seconds. Linking is done once the light flashes 3 times slowly.

For other remote

1. Learning code:
2. Press the "I" (ON) button in any group zone 3 times within 3 seconds. Linking is done once the light flashes 3 times slowly.

6.2. Unlink with remote

For K1 remote

1. Learning code:
2. Press “SET” 5 times within 3 seconds. Unlinking is done once the light flashes 10 times quickly.

For other remote

1. Learning code:
2. Press the "I" (ON) button in any group zone 5 times within 3 seconds. Unlinking is done once the light flashes 10 times quickly.

6.3. Compatible Remote (purchase separately)

FUT006, FUT007, B1/B1-B/T1, B2/T2, K1/K1-B, FUT087/FUT087-B, S1-B/S1-W/S1-G

6.4. Set up min brightness with remote

⚠️ This function should be paired with the remote first before setting.

For K1 remote

1. Long press “SET” for 3 seconds until the light flashes once, indicating it is going into flashing status.
2. Short press “SET” to cycle through 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Short press any button to confirm the setting, or wait for 10 seconds for automatic confirmation. The light will recover to the previous brightness level.

For other remote

1. Long press the "OFF" button on the remote or the "O" button on the zone until the light flashes once, indicating it is going into flashing status.
2. Short press the "OFF" button on the remote or the "O" button on the zone to set up 10 different brightness levels (3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%).
3. Short press any button except “OFF” to confirm the setting, or wait for 10 seconds for automatic confirmation. The light will recover to the previous brightness level.

Note: The Master OFF button can set the lowest brightness for all connected dimmers.

6.5. Auto transmitting

One light can transmit signals from the remote control to another light within 30m. As long as there is a light within 30m, the remote control distance can be limitless.

Diagram illustrating signal transmitting between two Triac Dimmers over a distance of 30m.

Note: All dimmers must be linked with the same remote.

7. Smartphone APP Control Instruction

Added Zigbee 3.0 gateway into the “TUYA Smart” App (please review the instruction of the Zigbee 3.0 gateway).

7.1. Pairing Network

1. Connect with power supply.
2. Pairing network (Note: factory default is pairing network).
   • Way 1: Long press “SET” for about 3 seconds until the indicator flashes quickly.
   • Way 2: Long press the push switch for 10 seconds while the light is OFF status (Note: requires wiring with a Push switch).
3. Open the “TUYA Smart" APP, click on the Zigbee gateway, then click “Add sub device”.
4. Click "Indicator is flashing quickly".
5. Support APP dimming or group control, etc., once added successfully.

Screenshots of the TUYA Smart app showing the process of adding a device, including the 'Zigbee Gateway' list, 'Add subdevice' button, and confirmation that the 'Indicator is flashing quickly'.

7.2. App set up lowest brightness

The light turns off when dimming brightness reaches 1%. Please increase the lowest brightness setting.

Setting way:

1. Click "Settings" in the APP.
2. Move the slider to finish setting.

Screenshots of the app interface showing brightness adjustment and the 'Minimum brightness setting' slider.

7.3. Breaker Mode (ON/OFF)

⚠️ Note: This mode only supports turning the light ON/OFF; dimming is not possible once this mode is activated.

Setting way:

1. Click "Settings" in the APP.
2. Click the button on the right side of "Breaker Mode".

Screenshots of the app interface showing the 'Breaker Mode' toggle switch.

8. Philips Hue Control Instruction

Added "Philips Hue" integration into the app.

8.1. Pairing Network

1. Connect with power supply.
2. Pairing network (Note: factory default is pairing network).
   • Way 1: Long press “SET” for about 3 seconds until the indicator flashes quickly.
   • Way 2: Long press the push switch for 10 seconds while the light is OFF status (Note: requires wiring with a Push switch).
3. Open the “Philips Hue" App, click “SETTINGS”, and click “Lights”.
4. Click "+" on the top right corner.
5. Click "Search".
6. Click "Start configuration". Follow the app instructions to complete configuration.

Screenshots of the Philips Hue app showing the 'Settings' menu, 'Lights' section, the '+' button for adding lights, the 'Add lights' screen with 'Search' option, and the 'Searching for lights...' status.

9. Alexa Voice Control Instruction

9.1. Alexa Control (Audio support Zigbee 3.0 protocol)

You can connect directly if your Amazon ECHO device has built-in Zigbee 3.0 protocol. Compatible models include: Amazon ECHO Plus (2nd Gen), ECHO (4th Gen), ECHO Studio, ECHO Show (2nd Gen).

Pairing Network

1. Connect with power supply.
2. Pairing network (Note: factory default is pairing network).
   • Way 1: Long press “SET” for about 3 seconds until the indicator flashes quickly.
   • Way 2: Long press the push switch for 10 seconds while the light is OFF status (Note: requires wiring with a Push switch).

Say to Amazon ECHO:

"Alexa, Discover devices"

Wait for a while to discover the device; voice control will be activated.

Illustration of an Amazon Echo device with a speech bubble indicating "Alexa, Discover devices".

9.2. Alexa Control (Audio does not support Zigbee 3.0 protocol)

Please add the device into the Miboxer Zigbee 3.0 gateway if your Alexa does not support Zigbee 3.0 protocol (check details on page 10), then follow these steps:

1. Open the Alexa App.
2. Click "More" on the bottom right corner.
3. Click "Skills & Games".
4. Click the search icon (?) on the top right corner.
5. Type "Smart life" and search.
6. Click the "Smart life" skill, follow the instructions to finish configuration, and start voice control.

Screenshots of the Alexa app showing navigation to 'Skills & Games', the search function, and the 'Smart life' skill.

10. Google Home Voice Control Instruction

Please add the device into the Miboxer Zigbee 3.0 gateway (check details on page 10) and start following these steps:

1. Open the Google Home App.
2. Click "+" on the top left corner.
3. Click "Set up device".
4. Click "Works with Google".
5. Click the search icon (?) on the top right corner.
6. Type "Smart life" and search.
7. Click the "Smart life" skill, follow the instructions to finish configuration, and start voice control.

Screenshots of the Google Home app showing the process of adding a device, including the '+' button, 'Set up device', 'Works with Google', and the search for 'Smart life' skill.

11. Attention

1. Please turn off the power supply before installation.
2. Please ensure the input voltage matches the device requirements.
3. Do not disassemble the device if you are not an expert, as it may cause damage.
4. Please do not use the light in areas with large metal surfaces or strong electromagnetic waves nearby, as this may seriously affect the remote control distance.

Made in China

[CE Mark] [UKCA Mark] [RoHS Compliant] ?? Dimmer cannot be used in humid areas.