MiBoxer 2 in 1 LED Controller (Zigbee 3.0 + 2.4G)

Product Features

Made with new Zigbee 3.0 wireless transmitting technology, this controller offers low power consumption and strong ability to build networks automatically with anti-interference. When used with a MiBoxer Zigbee gateway, it enables wireless dimming, color temperature, and brightness control, remote control, timing control, group control, and music rhythm functions. It also supports 2.4G RF remote control.

• Color temperature adjustable ?️
• Dim brightness ?
• Follows Zigbee 3.0 standard protocol ?
• Supports Zigbee 3.0 remote control (Zigbee 3.0 gateway is needed) ?
• Supports 2.4G Remote control ?
• Auto-transmitting ?
• Supports Smartphone app control (Zigbee 3.0 gateway is needed) ?
• Supports third-party voice control (Zigbee 3.0 gateway is needed) ?️

Various control solutions are supported, including:

Philips Hue ?, MiBoxer Zigbee Gateway ?, IKEA TRÅDFRI ?, 2.4GHz Remote ?, Amazon Echo Plus ?. This product is Powered by Tuya ⚡.

Set Up Output Mode

Set the correct output mode based on the feature of your lights. Setting method: Press the "SET" button continuously to switch output mode. Note: The system will log out without operation within 3 seconds.

Output mode sheet (confirm output mode based on indicator color):

PUSH Dimming

Short press PUSH switch: Turn ON/OFF light.

Long press PUSH switch:

• Stepless dimming brightness.
• Long press and release your finger, then repeat long pressing to increase or decrease brightness.

Diagram shows a square button labeled "PUSH".

Compatible with these 2.4G RF Remote Controls (Purchased Separately)

The document lists several compatible remote control models with images: FUT006, FUT007, B1/B1-B/T1, B2/T2, K1/K1-B, FUT087, FUT087-B, S1-B/S1-W, S1-G, WL-Box1.

2.4G RF Remote Control Instruction

1). Linking Code Instructions

Step 1: Power off the light for 10 seconds and power on again, or short press "SET" one time, or turn on the light via PUSH switch. Diagram shows power source connected to light, with options to use SET button or PUSH switch.

Step 2: Short press the "I" button 3 times within 3 seconds. Diagram shows a remote with a button labeled "Link / Unlink" and an "I" symbol.

Step 3: Lights blink 3 times slowly, indicating successful linking. Diagram shows power source connected to light, with a confirmation of successful linking.

Note: If the light is not blinking slowly, linking failed. Please follow the steps again. Lights that have already been linked cannot be linked again.

2). Unlinking Code Instructions

Step 1: Power off the light for 10 seconds and power on again, or short press "SET" one time, or turn on the light via PUSH switch. Diagram shows power source connected to light, with options to use SET button or PUSH switch.

Step 2: Short press the "I" button 5 times within 3 seconds. Diagram shows a remote with a button labeled "Link / Unlink" and an "I" symbol.

Step 3: Lights blink 10 times quickly, indicating successful unlinking. Diagram shows power source connected to light, with a confirmation of successful unlinking.

Note: If the light is not blinking quickly, unlinking failed. Please follow the steps again. Lights that have not been linked do not need to be unlinked.

3). Auto Transmitting (2.4G RF Remote Signal)

The light can transmit remote signals to another light automatically when the distance between lights is up to 30m. The remote control distance remains unlimited. Attention: All lights must be linked with the same remote.

Diagram illustrates auto-transmitting: a light transmitting a signal to another light 30m away.

4). PWM High Frequency / Low Frequency Switching (Only for Remote Control)

Switch to high frequency (16KHz): Press the “OFF” button 1 time within three seconds and press the “ON” button 5 times. Activated successfully once the LED light flashes 2 times quickly.

Switch to low frequency (250Hz): Press the “ON” button 1 time within three seconds and press the “OFF” button 5 times. Activated successfully once the LED light flashes 2 times slowly.

5). "Do Not Disturb" Mode is Activated and Shut Down (Default Activated)

Turn on “Do Not Disturb” mode. This mode is widely used in areas with frequent power failures to save energy.

2.4G RF Remote Turn On and Turn Off Instruction

Turn on "Do Not Disturb" mode: Press the “OFF” button three times within three seconds and press the “ON” button three times. Activated successfully once the LED light flashes four times quickly.

Attention: Do not disturb mode activation:

1. When the light is OFF status (e.g., controlled by app or remote): The light will be OFF status once you turn off power and turn on again. The user must turn off and turn on power twice to activate the light, or use the APP/remote to activate it.
2. When the light is ON status: The light will be ON status once you turn off and turn on power one time.

Turn off "Do Not Disturb" mode: Press the “ON” button three times within three seconds and press the “OFF” button three times. Closed successfully once the LED light flashes four times slowly.

Attention: The light will always be in the “ON” status if you turn on and turn off power once the user has closed “Do Not Disturb” mode.

App turn on and off “Do Not Disturb” mode instruction (check details in page 6).

Smartphone App Control Instruction

Added Zigbee 3.0 gateway into the “Tuya Smart” App (please review the instruction of Zigbee 3.0 gateway).

1. Connect with power supply.
2. Pairing network (attention: factory default is pairing network).
   • Way one: Turn off and turn on the light 3 times or more than 3 times continuously; the light will be in breathing status.
   • Way two: Long press the "SET" key until the indicator light flashes.
3. Open the "Tuya Smart" APP, click the Zigbee gateway, then click “Add sub device".
4. Click "Indicator is flashing quickly".
5. Support APP dimming or group control, etc., once added successfully.

Screenshots show the process: "My home" screen with "Zigbee Gateway" selected, "Add subdevice" screen, "Ensure device is in pairing mode" prompt, and a "Done" screen confirming 1 device added.

App Turn On and Off "Do Not Disturb" Mode (Default Activated)

Click the light that needs to be set up or group controlled, then click "More" -> click "Power-on behavior" -> turn on or off.

Screenshots show navigating through the app: selecting a device, accessing "More" options, and then "Power-on behavior" settings.

Philips Hue Control Instruction

Added "Philips Hue" into APP.

1. Connect with power supply.
2. Pairing network (attention: factory default is pairing network).
   • Way one: Turn off and turn on the light 3 times or more than 3 times continuously; the light will be in breathing status.
   • Way two: Long press the "SET" key until the indicator light flashes.
3. Open the "Philips Hue" App, click “SETTINGS”, and click “Lights”.
4. Click “+” on the top right corner.
5. Click "Search".
6. Click "Start configuration", and follow the app instructions to complete configuration.

Screenshots show the process: Philips Hue app "Settings" menu, "Lights" section, "Add lights" screen with a search button, and "Searching for lights..." screen.

Alexa Voice Control Instruction

1). Alexa Control (Audio Support Zigbee 3.0 Protocol)

You can connect directly if your Amazon ECHO already has built-in Zigbee 3.0 protocol. Following models support Zigbee 3.0 protocol:

Amazon ECHO Plus (2nd Gen), ECHO (4th Gen), ECHO Studio, ECHO Show (2nd Gen).

1. Connect with power supply.
2. Pairing network (attention: factory default is pairing network).
   • Way one: Turn off and turn on the light 3 times or more than 3 times continuously; the light will be in breathing status.
   • Way two: Long press the "SET" key until the indicator light flashes.
3. Say to Amazon ECHO: “Alexa, Discover devices” ?️. Wait for a while to discover devices; voice control is activated.

Diagram shows an Amazon Echo device with the voice command "Alexa, Discover devices" displayed.

2). Alexa Control (Audio Does Not Support Zigbee 3.0 Protocol)

Please add the device into the MiBoxer Zigbee 3.0 gateway first (check details in page 6), then start following these steps:

1. Open the Alexa App.
2. Click “More” on the bottom right corner.
3. Click "Skills & Games”.
4. Click the search icon [Search Icon] on the top right corner.
5. Type in “Smart life” and search.
6. Click the "Smart Life" skill, follow the instructions to finish configuration and start voice control.

Screenshots show the Alexa app navigation: "More" menu, "Skills & Games" section, and the search results for "Smart life" skill.

Google Home Voice Control Instruction

Please add the device into the MiBoxer Zigbee 3.0 gateway (check details in page 6) and start following these steps:

1. Open the Google Home App.
2. Click “+” on the top left corner.
3. Click "Set up device”.
4. Click “Works with Google".
5. Click the search icon [Search Icon] on the top right corner.
6. Type in “Smart life” and search.
7. Click the "Smart Life" skill, follow the instructions to finish configuration and start voice control.

Screenshots show the Google Home app navigation: "Home" screen with "+", "Add to home" screen, "Set up a device" screen, and the "Works with Google" section with a search for "Smart Life".

Attention

1. Please turn off the power supply before installation.
2. Please ensure the input voltage is the same as the requirements from the device.
3. Do not disassemble the device if you are not an expert, otherwise, it will damage it.
4. Please do not use the light in a place with a widely ranged metal area or strong electromagnetic waves nearby, otherwise, the remote distance will be seriously affected.

Scan the QR code [QR Code] to watch Zigbee series video instruction, or enter the following link directly: https://miboxer.com/light/video/zigbee.html

Certifications: [CE Mark], [UKCA Mark], [RoHS Compliant]

Made in China.