HOMCOM 838-307V00 Upholstered Storage Bench
Model: 838-307V00
Product Overview
This document provides essential information for the HOMCOM 838-307V00 Upholstered Storage Bench. It is designed as a comfortable and functional piece of furniture for domestic use.
Maximum weight capacity: 150 kg (330 lbs).
The bench features an upholstered seat with a tufted design, armrests, and four supporting legs. It includes a storage compartment accessible by lifting the seat.
Important Information
IMPORTANT: RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Instructions for Use
- Place the bench stably on a flat floor.
- Keep away from open flames and heat sources.
- Avoid overloading the bench.
Precautions Before Assembly
- Prepare a clean and dry mounting area.
- Verify that the product is not damaged.
- Check that none of the pieces are missing.
Maintenance
- Clean with a soft fabric.
- Check the seating and structure regularly.
Storage Conditions
- The fabric should be stored completely dry, in a clean and dry place to avoid the risks of mold.
Safety Warnings
Beware of crushing and cutting hazards during assembly. The manufacturer declines all responsibility in case of damages due to bad installation or environmental factors.
If the bench is fitted with powered seat height adjustments, only trained personnel may replace or repair those components.
Assembly Instructions
Parts List
- A: Tufted Seat/Lid (x1)
- B: Left Armrest (x1)
- C: Right Armrest (x1)
- D: Base Frame (x1)
- E: Internal Support Frame (x1)
- F: Bottom Panel (x1)
- G: Leg (x4)
- H: Side Support Bracket (x4)
- I: Gas Lift/Support Strut (x1)
- J: M6x25 Screw (x16 + 1 spare)
- K: M6x35 Screw (x18 + 1 spare)
- M: Allen Key (x1)
- N: Washer (x6)
Assembly Steps
Step 1 (01)
Attach the Side Support Brackets (H) to the Internal Support Frame (E) using M6x25 Screws (J) and the Allen Key (M). Then, attach the Base Frame (D) to the Internal Support Frame (E) using M6x25 Screws (J) and the Allen Key (M).
Step 2 (02)
Attach the Left Armrest (B) and Right Armrest (C) to the assembled base structure (D, E) using M6x25 Screws (J) and the Allen Key (M).
Step 3 (03)
Turn the unit over. Attach the Bottom Panel (F) to the underside of the base assembly using M6x35 Screws (K), Washers (N), and the Allen Key (M).
Step 4 (04)
Attach the Legs (G) to the corners of the Bottom Panel (F) using M6x35 Screws (K) and the Allen Key (M).
Step 5 (05)
Carefully place the Tufted Seat/Lid (A) onto the main body of the bench, aligning the pre-attached hinges with the corresponding fittings on the internal frame (E).
Step 6 (06)
Install the Gas Lift/Support Strut (I). Attach one end to the designated fitting on the Seat/Lid (A) and the other end to the fitting on the Internal Support Frame (E) as shown in the diagram.
Assembly is now complete. Done.
Customer Support
If you have any questions or require assistance, please contact the customer care center.
United States
Phone: 001-877-644-9366
Email: customerservice@aosom.com
Imported by Aosom LLC, 27150 SW Kinsman Rd, Wilsonville, OR 97070 USA. Made in China.
Canada
Phone: 416-792-6088
Email: customerservice@aosom.ca
Imported by Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9. Made in China.
United Kingdom
Phone: 0044-800-240-4004
Email: enquiries@mhstar.co.uk
Importer Address: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. Made in China.
For recycling information, please refer to quefairedemesdechets.fr.
