Ecler VEO-XTI1CG2 / VEO-XRI1CG2 User Manual

Introduction

Thank you for choosing Ecler VEO-XTI1CG2 / VEO-XRI1CG2. This manual provides essential information for the proper installation, configuration, and operation of these devices. For optimal performance, please read and follow all instructions carefully.

Ecler products are designed for professional use. For maintenance, please contact authorized technical services.

All ECLER products come with a warranty. Please visit www.ecler.com or refer to the warranty card for details on validity and conditions.

1. Precautions

Important Warnings:

• Risk of Electric Shock: Do not open the apparatus. The lightning symbol indicates the presence of dangerous voltage.
• Caution: The exclamation mark symbol alerts users to important operating and maintenance instructions.
• Terminals marked with a symbol may carry sufficient magnitude to constitute an electric shock hazard. External wiring must be installed by qualified personnel.
• Do not expose the equipment to rain or humidity to prevent electrical shocks or fire hazards.
• This is a Class I construction apparatus and must be connected to a grounded power outlet.
• Do not dispose of this product as unsorted municipal waste. Contact your nearest electrical and electronic waste treatment center.
• This equipment has been tested and complies with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

Cleaning: Use a soft, dry, or slightly damp cloth with a neutral liquid detergent. Ensure no water enters the apparatus. Do not use alcohol, gasoline, solvents, or abrasive substances.

2. Box Contents

2.1 VEO-XTI1CG2 (Transmitter)

• 1 x Transmitter
• 2 x 3-pin Euroblock connectors
• 4 x Screws
• 2 x Detachable mounting brackets
• 1 x 12V DC power adapter with international plugs
• Quick start guide
• Warranty card

2.2 VEO-XRI1CG2 (Receiver)

• 1 x Receiver
• 2 x 3-pin Euroblock connectors
• 4 x Screws
• 2 x Detachable mounting brackets
• 1 x 12V DC power adapter with international plugs
• Quick start guide
• Warranty card

3. Description and Features

The VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver form a set of H.265 / H.264 over IP video extenders, enabling HDMI® distribution over 1Gb Ethernet networks with video resolutions up to 1080p@60Hz. These devices offer a professional, high-quality, low-bandwidth compression solution suitable for point-to-point and multipoint-to-multipoint configurations using a single Cat. 5e/6/7 cable up to 100m. They are ideal for applications requiring audio management, PoE, VideoWall composition, or RS-232 control, such as educational, commercial, or corporate installations.

3.1 Main Features

• HDMI® with video resolution up to 1920x1200p@60Hz 4:4:4.
• Transmission distance up to 100m via Cat. 5e/6/7 cable.
• Supports unicast transmissions on unmanaged networks over 1Gb and multicast signal extension.
• 1Gb managed networks.
• Videowall composition up to 9 x 9 screens.
• Audio embedding and extraction.
• Supports coded audio transmission, Main Stream and Sub Stream modes.
• RS-232, TCP/IP, WebGUI pass-through via the VEO-XCTRLG2 control module.
• HDCP 1.4 compatible.
• PoE function supported.
• Local 12V DC power supply.

4. Installation and Connections

4.1 Rack Mounting VEO-RK1CG2

This product can be mounted in the VEO-RK1CG2 3U rack accessory. Follow these steps:

1. Attach the included mounting ears to the product using the provided screws.
2. Insert the apparatus with the mounting ears into a 3U rack (up to 12 units can be installed vertically).
3. Secure the mounting ears to the rack using screws to complete the installation.

4.2 Network Requirements and Configuration

The VEO-XTI1CG2 and VEO-XRI1CG2 are compatible with various network hardware brands, but the network must support the following:

• Layer 3 managed network switch.
• IGMP snooping support.

Note: For optimal performance and to avoid interference, consult your network administrator for proper multicast configuration.

4.2.1 IP Address Configuration

The default IP address is "auto IP" in the range 169.254.10.x for transmitters and 169.254.20.x for receivers. Dynamic assignment is possible via the VEO-XCTRLG2 controller. Refer to the VEO-XCTRLG2 user manual for details.

You can verify the assigned IP address using the VEO-1CG2 Discovery App or by pressing the CH Select button on the front panel. Refer to the "Additional Functions of the CH Select Buttons" chapter for details.

IP addresses can be changed via the integrated web interface. Ensure the PC and VEO devices are on the same network domain for web access. Refer to the "Configuration via Web Interface" chapter.

Note: Static IP addresses must be configured manually.

4.2.2 Quick Start for Video Distribution

To start video transmission, a transmitter and receiver must be paired. Each VEO-XTI1CG2 can transmit video over the network using a unique channel ID. Channel IDs 0 to 762 identify an IP address, and each VEO-XRI1CG2 receiver can select a channel to receive an AV stream.

Channel IDs are typically set once during system configuration for transmitters, while receiver IDs are adjusted to display different content.

Channel ID can be selected in four ways:

• Front panel buttons (VEO-XTI1CG2 has a locked ID assignment by default; adjust via CFN mode by holding the DOWN button. Refer to "Additional Functions of the CH Select Buttons" chapter).
• Via the device's web page.
• Via the VEO-XCTRLG2 web page.
• Via RS-232.
• Via TCP using VEO-XCTRLG2.

4.2.3 Unicast Mode

For point-to-point extension, no additional configuration is needed.

Connections:

1. Connect the source device to the VEO-XTI1CG2 HDMI® input.
2. Connect the AUDIO IN/OUT port to a sound device and select the desired audio mode.
3. Connect the remote endpoint to the VEO-XRI1CG2 HDMI® output.
4. Connect the transmitter and receiver with a Cat5e/6/7 cable.
5. Connect the automation system to the transmitter's RS-232 port.
6. Connect the device to be controlled to the receiver's RS-232 port.
7. Power the VEO-XTI1CG2 and VEO-XRI1CG2 using the included power adapter.

Note: Ensure both devices have the same ID.

4.2.4 Multicast Mode

For multipoint-to-multipoint topologies, each transmitter and receiver requires a unique IP address. It is recommended to create a separate IP video network using managed network switches, preferably gigabit switches with IGMP support.

Connections:

1. Configure the IP address for each transmitter and receiver.
2. Connect source devices to the VEO-XTI1CG2 HDMI® inputs.
3. Connect HDMI® endpoints to the VEO-XRI1CG2 HDMI® outputs.
4. Connect the AUDIO IN/OUT port to a sound device and select the desired audio mode.
5. Connect the automation system to the transmitters' RS-232 ports via cable.
6. Connect the receivers to the control devices' ports via RS-232 cables.
7. Connect all VEO devices to the network switch using Cat. 5e/6/7 cables.
8. Power the VEO-XTI1CG2 and VEO-XRI1CG2 with the included adapter. If the switch supports PoE, local power is not required.
9. Select the desired channel ID for each VEO device to establish the necessary video transmission flows.

5. Startup and Operation

5.1 Configuration via Web Interface

The VEO-XTI1CG2 and VEO-XRI1CG2 can be configured via their integrated web interface by entering the device's IP address in a web browser. Refer to the "IP Address Configuration" chapter for details on finding the IP address.

Default login credentials:

• Username: admin
• Password: admin

Once logged in, the web configuration menus allow users to manage various functionalities.

5.1.1 Information

The Status page provides basic information about the VEO-XTI1CG2 and VEO-XRI1CG2, including:

• Firmware Version
• IP Address
• Subnet Mask
• Gateway
• MAC Address

5.1.2 Video Configuration

5.1.2.1 VEO-XTI1CG2 Video Configuration

The video configuration page allows adjusting the following parameters:

• Main Stream:
  • Video Encoding Format: H.265 or H.264.
  • Audio Encoding Format: PCM or AAC.
  • Resolution: Displays HORIZONTAL and VERTICAL resolution, matching the input source.
  • Bitrate: Adjusts video quality by setting the maximum transmitted data.
• Sub Stream:
  • Video Encoding Format: H.265 or H.264.
  • Resolution: Sets HORIZONTAL and VERTICAL resolution.
  • Bitrate: Adjusts video quality by setting the maximum transmitted data.
• Audio Selection: Choose between ANALOG (from AUDIO IN) or HDMI® audio.
• EDID Setting: Selects EDID configuration for the VEO-XTI1CG2. Refer to "Additional Functions of the CH Select Buttons" for details.

EDID Table:

User EDID 1 and 2 can be loaded from downloaded files.

5.1.2.2 VEO-XRI1CG2 Video Configuration

The video configuration page allows adjusting the following parameters:

• Transmission: Select UNICAST or MULTICAST as the network transmission protocol.
• Scaler Setting: Adjusts the output resolution scaling for the VEO-XRI1CG2 HDMI® OUT port.

Resolution Table:

• Download EDID: Allows downloading the EDID file from the endpoint to the PC, which can be used as a user EDID file for the VEO-XTI1CG2.
• Video Timeout Setting: Sets the timeout for turning off the HDMI® OUT port when no video signal is detected. Setting to "0" disables this function.
• ID Setting:
  • Local ID: Sets the channel ID for the VEO-XRI1CG2 receiver (1-762 profiles).
  • Max Channel ID: Sets the available channel ID range for VEO-XRI1CG2 devices in an installation. Setting to "0" enables the full range (1-762 channels).
  • Source Selection ID: Sets the transmission channel for the VEO-XRI1CG2 receiver (1-762 channels). When a transmitter and receiver are tuned to the same channel, video is displayed from the VEO-XRI1CG2 HDMI® output.
• Picture Setting: Adjusts video parameters (brightness, contrast, hue, and saturation) for optimal display.

5.1.3 LED

This page allows selecting the LED status for both VEO-XTI1CG2 and VEO-XRI1CG2:

• Front Panel Power LED Flash:
  • ON: LED stays on permanently.
  • OFF: LED turns off automatically after 90 seconds.
• Power LED Flashing:
  • ON: LED flashes permanently.
  • OFF: LED stays on without flashing.
  • ON 90s: LED flashes for 90 seconds and then stops.

5.1.4 Configuration

5.1.4.1 VEO-XTI1CG2 Configuration

This page allows modifying the network configuration of the VEO-XTI1CG2:

• Network (Red): Configure IP address, Subnet Mask, Gateway, and HTTP Web Port.

Note: Network configuration can only be set when the MODE button is in Static. After changes, you must log in again with the new credentials.

• Security: Enable or disable HTTPS protocol.
• Setting: Adjust the Local ID for the VEO-XTI1CG2 transmitter (0-762 profiles).
• Button Fast Setting Local ID: Enables front panel buttons to change the device ID.
• Username: Modify the assigned username.
• Login: Change the password to access the web configuration page.

5.1.4.2 VEO-XRI1CG2 Configuration

This page allows modifying the network configuration of the VEO-XRI1CG2:

• Network (Red): Configure IP address, Subnet Mask, Gateway, and HTTP Web Port.

Note: Network configuration can only be set when the MODE button is in Static. After changes, you must log in again with the new credentials.

• Security: Enable or disable HTTPS protocol.
• Setting:
  • Local ID: Sets the channel ID for the VEO-XRI1CG2 receiver (1-762 profiles).
  • Max Channel ID: Sets the available channel ID range (0 disables the full range).
  • Source Selection ID: Sets the transmission channel for the VEO-XRI1CG2 receiver.
• Username: Modify the assigned username.
• Login: Change the password to access the web configuration page.

5.1.5 Update

5.1.5.1 VEO-XTI1CG2 Update

• Firmware Update:
  • Browse: Import the update file.
  • Update: Start the update process. The device will restart upon completion.
• Factory Reset: Resets the device to factory default settings.
• Reboot: Restarts the device.

5.1.5.2 VEO-XRI1CG2 Update

• Firmware Update:
  • Browse: Import the update file.
  • Update: Start the update process.
• IMG Update:
  • Browse: Import the startup screen image file.
  • Update: Start the startup screen image update.
• Factory Reset: Resets the device to factory default settings.
• Reboot: Restarts the device.

5.1.6 Close Session

Selecting "Close Session" logs out of the WebGUI and returns to the login interface.

5.2 Remote Control

5.2.1 RS-232

To pair a transmitter ID with a receiver ID, connect the RS-232 port of the VEO-XTI1CG2 and VEO-XRI1CG2 to a PC serial interface or an RS-232 control system, or use the optional VEO-XCTRLG2 controller.

5.2.1.1 RS-232 Communication Protocol

Serial parameters for correct transmission:

• Baud rate: 115200
• Data bits: 8
• Stop bits: 1
• Parity: None
• Flow control: None

5.2.1.2 Command List

Add carriage return () and line feed () characters to the end of each command.

Command Format: "<Command> [Parameter 1] <Variable> [Parameter 2]"

Example: Switching the transmission channel of a VEO-XRI1CG2 (Rx) to receive content from a VEO-XTI1CG2 (Tx):

• VEO-XTI1CG2: "local ID" parameter defines a unique ID for the transmitter and the transmission channel.
• VEO-XRI1CG2: "local ID" parameter defines a unique ID for the receiver. "Source Local ID" defines the transmission channel the receiver is tuned to.

The command to use is "SET DEC [dec] SWITCH [enc] ALL". Example: "SET DEC 1 SWITCH 2 ALL\r\n".

Command Table:

Note: (1)enc=000: All transmitters; enc=[001...762]: One transmitter. (2)dec=000: All receivers; dec=[001...762]: One receiver.

Note: The "enc=0" in the command means no source is present.

Note: Any TX can control any TX and RX. The following API elements from 1 to 7 can be used.

Note: RX can only set parameters for the device connected to the serial port, and only API elements 1 to 4 and 7 can be used.

5.2.2 Advanced Network Management

For larger multicast AV over IP scenarios involving multiple VEO-XTI1CG2 and VEO-XRI1CG2 devices, it is recommended to add a VEO-XCTRLG2 controller module. This unit allows users to manage and operate all transmitters and receivers from a single web interface, including preview mode, matrix control, videowall management, and TCP commands. For more information on advanced network control interface design, consult the VEO-XCTRLG2 controller user manual.

5.3 Ecler VEO1CG2 Discovery Application

The Ecler VEO1CG2 Discovery App is downloadable software available on the Ecler official website. It runs as a standalone application and automatically detects all VEO-1CG2 series devices connected to the local network.

Interface Functions:

• A. Ethernet/IP Selection: Select the PC's network interface for communication with connected devices.
• B. Active Devices: Displays a summary of detected devices (transmitters, receivers, wall plate units) for system status verification.
• C. Search: Performs a new scan and updates the list with newly detected devices.
• D. Save: Exports the device list and data to a local .txt file.
• E. Clear: Clears the current list from the screen.

Table provides the following information for each device:

1. ID: Unique identifier assigned to the device.
2. Type: Device Model:
   • TX: VEO-XTI1CG2 Transmitter Unit
   • WTX: WPTI1CG2 Wall Plate Transmitter
   • RX: VEO-XRI1CG2 Receiver Unit
3. Name: Custom device name configured via WebGUI.
4. MAC Address: Physical MAC address of the device.
5. IP Address: Device IP address. Clicking the blue link opens the device's WebSettings page.
6. Netmask: Device subnet mask.
7. Gateway: Device gateway address.
8. Firmware: Currently installed firmware version.

6. Panel Functions

6.1 VEO-XTI1CG2 (TX, TRANSMITTER)

6.1.1 Front Panel

1. POWER LED: Flashes when the unit receives power and stays lit (red) after startup.
2. LINK LED: Network connection status:
   • Solid light: Stable network connection with compatible video signal.
   • Off: No network connection.
   • Slow flashing: Stable network connection, but no video signal.
   • Fast flashing: Stable network connection, but no compatible video signal (resolution or frame rate exceeds native).
3. STATUS DISPLAY: Shows current channel ID and device information. Pressing "SHOW ME" in VEO-XCTRLG2 makes the status display flash "SHO" to locate the device. Refer to "Additional Functions of the CH Select Buttons" for details.
4. CHANNEL SELECT (▲ Up / ▼ Down): Adjust the device's channel ID. Also used to adjust audio mode, manage EDID, check IP address, or enter configuration mode. Refer to "Additional Functions of the CH Select Buttons" for details.
5. RESET: System reset button. Holding for 5 seconds restarts the device and restores factory settings.

6.1.2 Rear Panel

• 6. RS-232: Serial port for remote control. Supports signal pass-through.
• 7. AUDIO IN/OUT:
  • AUDIO IN: Acts as audio input (audio embedded to HDMI®).
  • AUDIO OUT: Acts as audio output (audio extraction from HDMI®).
• 8. LAN CONNECTOR (PoE): Connect to a 1Gb Ethernet switch for data transmission. If the switch supports PoE, local power is not required.
• 9. NETWORK Indicator (green):
  • Solid light: Network cable is correctly connected.
  • Off: No network connection.
• 10. DATA Transmission Indicator:
  • Flashing: Data transmission in progress.
  • Off: No data transmission.
• 11. HDMI IN: HDMI® input port.
• 12. 12V DC PORT: Connect to the included 12V DC power supply.

6.2 VEO-XRI1CG2 (RX, RECEIVER)

6.2.1 Front Panel

1. POWER LED: Flashes when the unit receives power and stays lit (red) after startup.
2. LINK LED: Network connection status:
   • Solid light: Stable network connection with compatible video signal.
   • Off: No network connection.
   • Slow flashing: Stable network connection, but no video signal.
   • Fast flashing: Stable network connection, but no compatible video signal (resolution or frame rate exceeds native).
3. STATUS DISPLAY: Shows current channel ID and device information. Pressing "SHOW ME" in XCTRLG2 makes the status display flash "SHO" to locate the device. Refer to "Additional Functions of the CH Select Buttons" for details.
4. CHANNEL SELECT (▲ Up / ▼ Down): Adjust the device's channel ID. Also used to adjust audio mode, manage EDID, check IP address, or enter configuration mode. Refer to "Additional Functions of the CH Select Buttons" for details.
5. RESET: System reset button. Holding for 5 seconds restarts the device and restores factory settings.

6.2.2 Rear Panel

• 6. RS-232: Serial port for remote control. Supports signal pass-through.
• 7. AUDIO OUT: Audio port acts as an audio de-embedder from HDMI®.
• 8. LAN CONNECTOR (PoE): Connect to a 1Gb Ethernet switch for data transmission. If the switch supports PoE, local power is not required.
• 9. NETWORK Indicator (green):
  • Solid light: Network cable is correctly connected.
  • Off: No network connection.
• 10. DATA Transmission Indicator:
  • Flashing: Data transmission in progress.
  • Off: No data transmission.
• 11. HDMI OUT: HDMI® output port.
• 12. 12V DC PORT: Connect to the included 12V DC power supply.

6.3 Additional Functions of CH SELECT Buttons (Channel Selection) for VEO-XTI1CG2 and VEO-XRI1CG2

7. Technical Information

7.1 Technical Specifications

Video Performances

• Video Input Connector: HDMI® Type A Female, 10.2 Gbps
• Video Output connector: HDMI® Type A Female, 10.2 Gbps
• Video Input Resolution: Up to 1920x1200 60Hz
• Video Output Resolution: Up to 1920x1200 60Hz
• Video Codec: H.265 and H.264
• Transmission Latency: <100ms compression depending on video content and transmission / network configuration
• Chroma Subsampling: RGB4:4:4, YCbCr 4:4:4, YCbCr 4:2:2
• Colour Depth: 8-bit, 10-bit, 12-bit, 16-bit (1080p@60Hz)
• Colour Space: RGB, YCbCr
• HDCP: 1.4
• HDR: Not supported
• Video Composing Capabilities: Videowall up to 9x9
• Scaling Feature: Supported
• HDMI Distance: 15m with Ecler VEO Cables

Audio Performances

• Audio Input Connectors: 3-pin Euroblock (Stereo Unbalanced)
• Audio Output Connectors: 3-pin Euroblock (Stereo Unbalanced)
• Audio Formats: LPCM 2.0CH
• Sample Rate: 32/44.1/48KHz
• Bit Depth: Up to 24-bit
• Frequency Response: 20Hz-20KHz
• ARC/eARC: Not Supported

Control

• Control Connectors: RJ-45, Euroblock
• Control Protocols: Web, TCP (only with VEO-XCTRLG2), RS-232
• Control Buttons: 1 x UP button, 1 x DOWN button
• EDID Management: Via front panel and Web settings
• Status Indicators: POWER LED: Red; LINK LED: Green; LCD display
• Pass-through Control: Euroblock
• Pass-through Connectors: Euroblock
• Pass-through Protocols: RS-232

Network

• Network Connectors: RJ-45
• Network Requirements: IGMP Snooping
• Average Streaming Bitrate: Configurable via software 1- 20Mbps
• Transmission Distance: 100m (Ethernet Standard)

Electrical

• Power Supply: PoE (802.3af Class 3) or External Power supply
• AC Mains Connector: 100-240VAC 50-60Hz with EU, UK, US, AU blades
• DC Mains Connector: 12VDC-1A with coaxial DC connector
• Power Consumption: Transmitter: 3W / Receiver: 3W

7.2 Mechanical Diagram

7.2.1 VEO-XTI1CG2

Diagram showing the front, side, and rear views of the VEO-XTI1CG2 with dimensions.

7.2.2 VEO-XRI1CG2

Diagram showing the front, side, and rear views of the VEO-XRI1CG2 with dimensions.

Physical

• Operating Temperature: Min. -10°C - 14°F; Max. 45°C - 113°F
• Operating Humidity: <90% HR
• Installation Options: Desktop, 19" racks (1/2RU), VEO-RK1CG2
• Included Accessories: 2x 3pins Euroblock connector, 4x M3 screws 4mm, 2x Mounting Ears, 1x 12V PSU
• Optional Accessories: VEO-XCTRLG2, VEO-RK1CG2
• Dimensions (WxHxD): 95 x 21.5 x 120mm / 3.74 x 0.85 x 4.72in. (each one, TX and RX separately)
• Shipping Dimensions (WxHxD): 188 x 75 x 137 mm / 7.40 x 2.95 x 5.39 in. (each one, TX and RX separately)
• Weight: 0.3 Kg / 0.66 lb (each one, TX and RX separately)
• Shipping Weight: 0.7 Kg (each one, TX and RX separately)
• Chassis Material: Metal
• Finished Colour: Black

Disclaimer

All product features are subject to change due to production tolerances. NEEC AUDIO BARCELONA, S.L. reserves the right to make changes or improvements to the design or manufacturing that may affect product specifications.

For technical inquiries, please contact your supplier, distributor, or complete the contact form on our website at Support / Technical Inquiry.

Motors, 166-168 08038 Barcelona - Spain - (+34) 932238403 | information@ecler.com | www.ecler.com