Ecler VEO-XTI1CG2 / VEO-XRI1CG2 User Manual

1. Precautions

This section outlines important safety precautions, including warnings about electric shock, proper handling, cleaning, and disposal of the equipment. It emphasizes reading all instructions and seeking qualified service for repairs.

Important Notes:

• CAUTION: RISK OF ELECTRIC SHOCK - DO NOT OPEN
• WARNING: SHOCK HAZARD - DO NOT OPEN
• The lightning bolt symbol indicates dangerous voltage within the product.
• The exclamation mark symbol indicates important operation and maintenance instructions.
• Ensure proper grounding of the unit.
• Do not expose the device to rain or moisture.
• Dispose of the product responsibly at designated electronic waste collection centers.
• The device complies with FCC Part 15 regulations for Class A digital devices.

Cleaning: Clean only with a soft, dry cloth, or one slightly dampened with water and mild liquid soap. Never use alcohol, benzine, solvents, or abrasive cleaners.

2. Package Contents

Each package includes:

For VEO-XTI1CG2 (Transmitter):

• 1 Transmitter
• 2 x 3-pin Euroblock connectors
• 4 x Screws
• 2 x Removable mounting brackets
• 1 x 12V DC power adapter with international pins
• Quick start guide
• Warranty card

For VEO-XRI1CG2 (Receiver):

• 1 Receiver
• 2 x 3-pin Euroblock connectors
• 4 x Screws
• 2 x Removable mounting brackets
• 1 x 12V DC power adapter with international pins
• Quick start guide
• Warranty card

3. Description and Characteristics

The VEO-XTI1CG2 transmitter and VEO-XRI1CG2 receiver are part of an H.265/H.264 over IP HDMI extender system. They provide high-quality, low-bandwidth video compression for point-to-point and multipoint configurations over a single Cat5e/6/7 cable up to 100 meters. These devices are suitable for educational, commercial, and enterprise applications requiring flexible and scalable audiovisual systems. They can also be used with the VEO-XCTRLG2 control module for extended management.

Main Features:

• HDMI® video resolution up to 1920x1200p at 60 Hz, 4:4:4.
• Transmission distance up to 100m over Cat5e/6/7 cable.
• Supports unicast on unmanaged 1 Gbit/s networks and multicast signal extension.
• 1 Gbit/s managed networks.
• Supports video wall composition up to 9x9 configurations.
• Supports audio integration and extraction.
• Supports main and secondary stream encoding modes.
• Supports RS-232, TCP/IP, and WebGUI control via the VEO-XCTRLG2 controller module.
• HDCP 1.4 compatible.
• Supports Power over Ethernet (PoE).
• Local 12V DC power supply.

4. Installation and Connection

4.1 Rack Mounting in VEO-RK1CG2

The units can be installed in a 3U rack accessory (VEO-RK1CG2). Follow these steps:

1. Attach the two mounting brackets to the product using the provided screws.
2. Insert the product with its mounting brackets into the 3U rack accessory.
3. Secure the mounting brackets to the rack with screws.

4.2 Network Requirements and Configuration

The VEO-XTI1CG2 and VEO-XRI1CG2 are compatible with various network hardware but require:

• An L3 managed network switch.
• IGMP snooping support.

It is recommended to consult with the network administrator for proper configuration to avoid performance issues.

4.2.1 IP Address Setting

Default IP addresses are 169.254.10.x for the transmitter and 169.254.20.x for the receiver. The VEO-XCTRLG2 can also assign IP addresses. You can verify the IP address using the Ecler VEO-1CG2 Discovery application or by pressing the '▲' button on the front panel.

IP addresses can be changed via the integrated Web GUI. Ensure your computer and the VEO devices are on the same network domain.

Note: Static IP addresses must be set manually for each device.

4.2.2 Quick Setup for Video Distribution

To establish video transmission, match the transmitter and receiver. Each VEO-XTI1CG2 can broadcast video using a unique channel number. Receivers (VEO-XRI1CG2) select these channels to receive the audiovisual stream.

Channel selection can be done via:

• Front panel buttons (VEO-XTI1CG2 ID is locked by default; refer to manual for unlocking).
• Web GUI on the device.
• Web GUI on the VEO-XCTRLG2.
• RS-232.
• TCP via VEO-XCTRLG2.

4.2.3 Unicast Mode

For simple point-to-point extension, no additional configuration is needed. Connect the source to the transmitter's HDMI IN, the display to the receiver's HDMI OUT, link the devices with Cat5e/6/7 cable, connect RS-232 if needed, and power both units. Ensure both devices share the same ID.

4.2.4 Multicast Mode

For point-to-multipoint or multipoint-to-multipoint setups, each transmitter and receiver needs a unique IP address. A managed gigabit network switch with IGMP support is recommended.

Connection steps:

1. Set IP addresses for transmitters and receivers.
2. Connect source devices to transmitter HDMI® ports.
3. Connect remote HDMI® devices to receiver HDMI® ports.
4. Connect audio input/output to audio devices.
5. Connect RS-232 cables for automation systems and devices to be controlled.
6. Connect all VEO devices to the network switch using Cat. 5e/6/7 cables.
7. Power the units using the provided adapter, or rely on PoE if available from the switch.
8. Select the desired channel for each VEO device to establish video transmission.

5. Startup and Operation

5.1 Web Interface Configuration

The VEO-XTI1CG2 and VEO-XRI1CG2 can be configured using their integrated Web interface. Access it by entering the device's IP address in a web browser. Default login credentials are 'admin' for both username and password.

5.1.1 Information

The Status page provides basic information such as Firmware Version, IP Address, Subnet Mask, Gateway, and MAC Address.

5.1.2 Video Settings

5.1.2.1 Video Settings for VEO-XTI1CG2

This page allows configuration of:

• Main Stream: Video Encoding Format (H.265/H.264), Audio Encoding Format (PCM/AAC), Resolution, and Bitrate.
• Sub Stream: Video Encoding Format (H.265/H.264), Resolution, and Bitrate.
• Audio Selection: Choose between ANALOGUE (integrates external audio into HDMI®) or HDMI® (extracts audio from HDMI®).
• EDID Setting: Select EDID settings for the transmitter. Options include preset resolutions and audio formats, copying EDID from the receiver, or using User EDID files.

5.1.2.2 VEO-XRI1CG2 Video Settings

This page allows configuration of:

• Transmission: Select UNICAST or MULTICAST protocol.
• Scaler Setting: Adjust output resolution for the HDMI® OUT port. A table lists available resolutions.
• Download EDID: Download EDID binary file from the destination device.
• Video Timeout Setting: Define the delay before HDMI® OUT deactivates when no video signal is detected.
• OSD Color Setting: Adjust OSD color parameters.
• Picture Setting: Adjust Brightness, Contrast, Hue, and Saturation.

5.1.3 LED Status

Configure the front panel and power LEDs:

• Front Panel Power LED Flash: ON (always on) or OFF (turns off after 90s).
• Power LED Flashing: ON (blinks continuously), OFF (stays on without blinking), or ON 90s (blinks for 90s then stops).

5.1.4 Settings

5.1.4.1 VEO-XTI1CG2 Settings

Configure network settings:

• Network: IP Address, Subnet Mask, Gateway, HTTP Web Port. These settings are only configurable when MODE is set to Static.
• Security: Enable or disable HTTPS protocol.
• Setting: Set the Local ID (channel identification) for the transmitter (0-762).
• Button Fast Setting Local ID: Enable/disable front panel ID changes.
• Username: Change the device username.
• Login: Change the current password.

5.1.4.2 VEO-XRI1CG2 Settings

Configure network settings for the receiver:

• Network: IP Address, Subnet Mask, Gateway, HTTP Web Port.
• Security: Enable or disable HTTPS protocol.
• Setting: Set Local ID (1-762), Max Channel ID (0-762), and Source Selection ID (0-762) for the receiver.
• Username: Change the device username.
• Login: Change the current password.

5.1.5 Update

5.1.5.1 VEO-XTI1CG2 Firmware Update

• Firmware Update: Browse for firmware file, then click Update. The device will reboot upon successful update.
• Factory Reset: Resets the device to factory default settings.
• Reboot: Restarts the device.

5.1.5.2 VEO-XRI1CG2 Update

• Firmware Update: Browse for firmware file, then click Update. The device will reboot upon successful update.
• IMG Update: Update the boot screen image.
• Factory Reset: Resets the device to factory default settings.
• Reboot: Restarts the device.

5.1.6 Disconnection

Select the disconnect/log out option to exit the Web GUI.

5.2 Remote Control

5.2.1 RS-232

Connect the RS-232 port of the VEO-XTI1CG2 and VEO-XRI1CG2 to a computer or control system for remote control. The optional VEO-XCTRLG2 module can also be used.

RS-232 Communication Protocol Parameters: Baud rate: 115200, Data bits: 8, Stop bits: 1, Parity: None, Flow control: None.

5.2.1.1 Command List

Commands require carriage return () and line feed () characters at the end. Example: SET DEC 1 SWITCH 2 ALL.

Commands for controlling transmitters and receivers:

Note: Transmitters can control any transmitter and receiver. Receivers can only control connected devices via the serial port (elements 1-4 and 7 of the API).

5.2.2 Advanced Network Management

For larger multicast AV over IP configurations, the VEO-XCTRLG2 controller module is recommended. It allows managing all transmitters and receivers from a single Web interface, including preview, matrix control, video wall management, and TCP commands.

Refer to the VEO-XCTRLG2 manual for more details.

5.3 Ecler VEO1CG2 Discovery Application

The Ecler VEO1CG2 Discovery application is a downloadable software that automatically detects all VEO-1CG2 series devices on the local network. It provides information such as ID, Type, Name, MAC Address, IP Address, Netmask, Gateway, and Firmware Version.

Interface Functions:

• A. Ethernet/IP Selection: Select the appropriate network interface.
• B. Active Devices: Displays a summary of detected devices.
• C. Search: Performs a new scan for devices.
• D. Save: Exports device list to a .txt file.
• E. Clear: Clears the current screen list.

The table provides details for each device, including its ID, Type (TX, WTX, RX), Name, MAC Address, IP Address, Netmask, Gateway, and Firmware Version.

6. Front Panel Functions

6.1 VEO-XTI1CG2 (TX, Transmitter)

6.1.1 Front Panel

• 1. LED POWER: Blinks during power-on, then stays solid red.
• 2. LED LINK: Network connection status. Solid green: stable connection with compatible video signal. Off: no network connection. Slow blink: stable connection, no video signal. Fast blink: stable connection, incompatible video signal (resolution/frame rate exceeds native value).
• 3. STATUS DISPLAY: Shows current channel and device information. Can be made to blink by the VEO-XCTRLG2's 'SHOW ME' function.
• 4. CH SELECT (▲/▼): Selects the device channel. Also used for audio mode, EDID, IP address, and configuration mode.
• 5. RESET: Resets the system to factory default settings. Holding for 5 seconds restarts the device.

6.1.2 Rear Panel

• 6. RS-232: Serial port for remote control.
• 7. AUDIO IN/OUT: AUDIO IN integrates external audio into HDMI®. AUDIO OUT extracts audio from HDMI®.
• 8. LAN CONNECTOR (PoE): Connects to a gigabit Ethernet switch for data transmission. PoE eliminates the need for local power.
• 9. LINK Indication (green): Solid: network cable connected. Off: no network connection.
• 10. DATA Indication (yellow): Blinking: data transmission. Off: no data transmission.
• 11. HDMI IN: HDMI® input port.
• 12. DC 12V PORT: Connect the provided 12V DC adapter.

6.2 VEO-XRI1CG2 (RX, Receiver)

6.2.1 Front Panel

• 1. LED POWER: Blinks during power-on, then stays solid red.
• 2. LED LINK: Network connection status (same as transmitter).
• 3. STATUS DISPLAY: Shows current channel and device information.
• 4. CH SELECT (▲/▼): Selects the device channel, audio mode, EDID, IP address, or enters configuration mode.
• 5. RESET: Resets the system to factory default settings. Holding for 5 seconds restarts the device.

6.2.2 Rear Panel

• 6. RS-232: Serial port for remote control.
• 7. AUDIO OUT: Extracts audio from HDMI®.
• 8. LAN CONNECTOR (PoE): Connects to a gigabit Ethernet switch for data transmission. PoE eliminates the need for local power.
• 9. LINK Indication (green): Solid: network cable connected. Off: no network connection.
• 10. DATA Indication (yellow): Blinking: data transmission. Off: no data transmission.
• 11. HDMI OUT: HDMI® output port.
• 12. DC 12V PORT: Connect the provided 12V DC adapter.

6.3 Additional Functions of CH SELECT Buttons

For VEO-XTI1CG2 / VEO-XRI1CG2:

• IP Address: Holding CH SELECT for 5 seconds displays the current IP address.
• Identifier (Channel): Holding CH SELECT for 5 seconds displays the current channel.
• Wake Up: Pressing CH SELECT wakes up the display if it's off.
• Configuration: Holding CH SELECT for 5 seconds enters Configuration mode ('CFN'). Use CH SELECT to navigate menus (Channel, EDID, Audio, Resolution, Timeout settings).
• Channel Setting (Receiver only): Simple press of CH SELECT (▲/▼) changes the receiver channel. For transmitters, changing the channel is not instantaneous. Holding CH SELECT for 5 seconds enters 'Channel Setting' mode.

EDID Setting (VEO-XTI1CG2 only): After displaying the channel menu, long-press CH SELECT to enter EDID setting mode. Use CH SELECT to select the desired EDID. Long-press again to confirm.

Audio Setting (VEO-XTI1CG2 only): After displaying the EDID menu, long-press CH SELECT to enter Audio setting mode. Select between AHE (HDMI audio) or AEI (external audio input).

Output Resolution Setting (VEO-XRI1CG2 only): Long-press CH SELECT to enter Resolution setting mode. Select the desired resolution from the provided list.

Video Deactivation Timeout Setting (VEO-XRI1CG2 only): Long-press CH SELECT to enter Timeout setting mode. Select the delay before HDMI® OUT deactivates after no video signal is detected.

7. Technical Data

7.1 Technical Characteristics

Video Performances

• Video Input Connector: HDMI® Type A Female, 10.2 Gbps
• Video Output Connector: HDMI® Type A Female, 10.2 Gbps
• Video Input Resolution: Up to 1920x1200 60Hz
• Video Output Resolution: Up to 1920x1200 60Hz
• Video Codec: H.265 and H.264
• Transmission Latency: <100ms compression
• Chroma Subsampling: RGB4:4:4, YCbCr 4:4:4, YCbCr 4:2:2
• Colour Depth: 8-bit, 10-bit, 12-bit, 16-bit
• Colour Space: RGB, YCbCr
• HDCP: 1.4
• HDR: Not supported
• Video Composing Capabilities: Videowall up to 9x9
• Scaling Feature: Supported
• HDMI Distance: 15m with Ecler VEO Cables

Audio Performances

• Audio Input Connectors: 3-pin Euroblock (Stereo Unbalanced)
• Audio Output Connectors: 3-pin Euroblock (Stereo Unbalanced)
• Audio Formats: LPCM 2.0CH
• Sample Rate: 32/44.1/48KHz
• Bit Depth: Up to 24-bit
• Frequency Response: 20Hz-20KHz
• ARC/eARC: Not Supported

Control

• Control Connectors: RJ-45, Euroblock
• Control Protocols: Web, TCP (with VEO-XCTRLG2), RS-232
• Control Buttons: 1 x UP button, 1 x DOWN button
• EDID Management: Via front panel and Web settings
• Status Indicators: POWER LED (Red), LINK LED (Green), LCD display

Pass-through Control

• Pass-through Connectors: Euroblock
• Pass-through Protocols: RS-232

Network

• Network Connectors: RJ-45
• Network Requirements: IGMP Snooping
• Average Streaming Bitrate: Configurable (1-20Mbps)
• Transmission Distance: 100m (Ethernet Standard)

Electrical

• Power Supply: PoE (802.3af Class 3) or External Power supply
• AC Mains Connector: 100-240VAC 50-60Hz
• DC Mains Connector: 12VDC-1A
• Power Consumption: Transmitter: 3W / Receiver: 3W

7.2 Schematics with Dimensions

Diagrams showing the front, side, and rear views of the VEO-XTI1CG2 and VEO-XRI1CG2 with dimensions are provided.

Physical Specifications

• Operating Temperature: -10°C to 45°C (14°F to 113°F)
• Operating Humidity: <90% HR
• Installation Options: Desktop, 19" racks (1/2RU), VEO-RK1CG2
• Included Accessories: 2x 3-pin Euroblock connectors, 4x M3 screws, 2x Mounting Ears, 1x 12V PSU
• Optional Accessories: VEO-XCTRLG2, VEO-RK1CG2
• Dimensions (WxHxD): 95 x 21.5 x 120mm (each unit)
• Shipping Dimensions (WxHxD): 188 x 75 x 137 mm (each unit)
• Weight: 0.3 Kg (each unit)
• Shipping Weight: 0.7 Kg (each unit)
• Chassis Material: Metal
• Finished Colour: Black

Contact Information

For technical questions, contact your supplier, distributor, or fill out the contact form on the Ecler website.

Ecler Address: Motors, 166-168 - 08038 Barcelona - Spain

Phone: (+34) 932238403

Email: information@ecler.com

Website: www.ecler.com