POWERSHRED DS-1200Cs

Key Components and Features

Key Components:

• A. SafeSense® Technology: Detects hand proximity to paper entry, stopping the shredder.
• B. Paper/Card Entry: The slot where paper and credit cards are fed.
• C. Handle: Located on top for easier carrying.
• D. Window: A clear panel to view the waste bin level.
• E. Pull-out Bin: The removable bin that collects shredded material.
• F. Disconnect Power Switch: The main power switch, located on the back (0 = OFF, I = ON).
• G. Safety Instructions: Reference to safety guidelines.
• H. Control Switch and Indicator Lights:
  • 1. Reverse (R): Used to back out jammed paper.
  • 2. OFF (0): Shuts down the shredder.
  • 3. Auto-On (Green Light): Activates the shredder when paper is detected in the entry.
  • 4. Overheat (Red Light): Indicates the motor has exceeded its operating temperature and needs to cool down.
  • 5. SafeSense® Indicator (Yellow Light): Illuminates when SafeSense® technology is active.

Capabilities

Shredding Capabilities:

• Will Shred: Paper, credit cards, staples, small paper clips, and junk mail.
• Will Not Shred: Continuous forms, adhesive labels, transparencies, newspaper, CD/DVDs, cardboard, large paper clips, laminates, file folders, X-rays, or plastic other than noted above.

Specifications:

• Paper Shred Size: Cross-Cut: 4mm x 50mm
• Maximum Sheets per Pass: 12*
• Maximum Cards per Pass: 1*
• Paper Entry Width: 225mm
• Note on Capacity: *Based on A4 (70g) paper at 220-240V, 50/60 Hz, 2.45Amps. Heavier paper, humidity, or voltage variations may reduce capacity.
• Recommended Daily Usage: Up to 120 sheets; 10 credit cards. (12 sheets per pass recommended to avoid jams).
• Operating Environment: Home and office environments between 50-80°F (10-26°C) and 40-80% relative humidity.

Important Safety Instructions

Read Before Using!

• Operation, maintenance, and service requirements are covered in the instruction manual. Read the entire manual before operating the shredder.
• Keep away from children and pets. Keep hands away from the paper entry. Always set the switch to OFF (0) or unplug the shredder when not in use.
• Keep foreign objects such as gloves, jewelry, clothing, hair, etc., away from shredder openings. If an object enters the top opening, switch to Reverse (R) to back out the object.
• Never use aerosol products, petroleum-based lubricants, or other flammable products on or near the shredder. Do not use canned air on the shredder.
• Do not use if the shredder is damaged or defective. Do not disassemble the shredder.
• Do not place the shredder near or over a heat source or water.
• This shredder has a Disconnect Power Switch (F) that must be in the ON (I) position to operate. In case of an emergency, move the switch to OFF (0) position. This action will stop the shredder immediately.
• Avoid touching exposed cutting blades under the shredder head.
• The shredder must be plugged into a wall outlet or socket matching the voltage and amperage designated on the label. The outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be used with this product.
• FIRE HAZARD: Do NOT shred greeting cards with sound chips or batteries.
• For indoor use only.
• Unplug the shredder before cleaning or servicing.

Basic Shredding Operation

Steps:

1. Power Up: Plug in the shredder and set the disconnect power switch (F) to the ON (I) position.
2. Set Mode: Set the control switch to Auto-On (I).
3. Feed Material: Feed paper or cards straight into the paper entry (B) and release. The shredder will start automatically.
4. Finish Shredding: When finished shredding, set the switch to OFF (0).

Continuous Operation Note:

Continuous operation is limited to a maximum of 5 minutes. The shredder runs briefly after each pass to clear the entry. Continuous operation beyond 5 minutes will trigger a 30-minute cool-down period.

Advanced Product Features

SafeSense® Technology:

SafeSense® Technology stops shredding immediately when hands touch the paper opening. To test its functionality: Set the shredder to Auto-On (I), touch the test area, and observe the SafeSense® indicator (yellow light) illuminate. This confirms SafeSense® is active and working properly.

Product Maintenance

Oiling Shredder:

All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding, and could ultimately stop running. To avoid these problems, Fellowes recommends oiling the shredder each time the waste bin is emptied. Follow the oiling procedure below and repeat twice.

Oiling Procedure:

1. Step 1: Set the shredder to OFF (0).
2. Step 2: Apply oil across the paper entry. (Use only a non-aerosol vegetable oil in a long nozzle container, such as Fellowes 35250).
3. Step 3: Set the shredder to Reverse (R) for 2-3 seconds.

Cleaning Auto-Start Infrared Sensors:

Paper detection sensors are designed for maintenance-free operation. However, on rare occasions, the sensors may become blocked by paper dust, causing the motor to run even if there is no paper present. (Note: two paper detection sensors are located in the center of the paper entry).

Cleaning Procedure:

1. Step 1: Turn off and unplug the shredder.
2. Step 2: Locate the auto-start infrared sensor.
3. Step 3: Dip a cotton swab in rubbing alcohol.
4. Step 4: Using the cotton swab, wipe away any contamination from the paper sensors.

Troubleshooting

Overheat Indicator:

When the Overheat Indicator (red light) is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain illuminated, and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and recovery time for this shredder.

SafeSense® Indicator:

If hands are too close to the paper entry, the SafeSense® indicator (yellow light) will illuminate, and the shredder will stop shredding.

Paper Jam:

Steps to Clear a Paper Jam:

1. Step 1: Set the shredder to Reverse (R) for 2-3 seconds.
2. Step 2: Alternate slowly between Reverse (R) and OFF (0) or Auto-On (I) to back out the paper.
3. Step 3: Gently pull any uncut paper from the paper entry.
4. Step 4: Set the shredder to OFF (0) and unplug it.
5. Step 5: Set the shredder to Auto-On (I) and resume shredding.

Limited Product Warranty

Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for 5 years from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, the sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge consumers for any additional costs incurred to provide parts or services outside the country where the shredder is initially sold by an authorized reseller.

Any implied warranty, including that of merchantability or fitness for a particular purpose, is hereby limited in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact Fellowes or your dealer.

Australia Residents Only:

Australian Consumer Law guarantees cannot be excluded. Consumers are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. Consumers are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under Fellowes' Warranty are in addition to other rights and remedies under a law in relation to the shredder.

Declaration of Conformity

Fellowes Manufacturing Company, Yorkshire Way, West Moor Park, Doncaster, South Yorkshire, DN3 3FB, England, declares that the product Model DS-1200Cs conforms with the requirements of the Restriction of Hazardous Substances Directive (2011/65/EU), the Low Voltage Directive (2006/95/EC), the Electromagnetic Compatibility Directive (2004/108/EC), the WEEE directives (2002/96/EC), and the harmonized European EN Standards: Safety: EN 60950-1; EMC Standard: EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3. Year Affixed: 12. Location: Itasca, Illinois, USA. Date: January 1, 2013.

WEEE Information

This product is classified as Electrical and Electronic Equipment. When disposing of this product, please ensure it is done in accordance with the European Waste of Electrical and Electronic Equipment (WEEE) Directive and in compliance with local laws relating to this directive. For more information on the WEEE Directive, please visit www.fellowesinternational.com/WEEE.

Questions or Concerns?

Customer Service & Support:

• Website: www.fellowes.com
• Support Topics: Troubleshooting, Registration, Manuals, Replacement Parts, General Questions.
• Australia: +61-1-800-33-11-77
• Europe: 00800-1810-1810
• United Kingdom: +44-(0)-1302-836800
• United States: +1-800-955-0959

Address: Fellowes, 1789 Norwood Avenue, Itasca, Illinois 60143-1095 USA. Phone: 630-893-1600.

©2013 Fellowes, Inc. Part No. 404584 Rev C