Fellowes P-48C Cross-Cut Shredder

Introduction

This document provides essential instructions for the safe and effective operation of the Fellowes P-48C Cross-Cut Shredder. Please read these instructions carefully before using the shredder.

Shredder Overview

The Fellowes P-48C shredder features the following components:

• Handle: For carrying the shredder head.
• Shredder head: Contains the cutting mechanism.
• Sheet capacity gauge: Indicates the maximum number of sheets that can be fed.
• LED Lights:
  • Overheated (red) indicator.
  • Standby (green) indicator.
• Window: Allows viewing of the bin level.
• Bin: Collects shredded material.
• Easy emptying: Feature for convenient bin removal.
• Paper/credit card entry: Slot for feeding documents and cards.
• Disconnect power switch: Located on the back of the shredder head.
• Safety lock: Prevents accidental operation.
• Control switch: With settings for Auto-On (I), Off (0), and Reverse (R).

Capabilities

What the Shredder Will Shred:

• Paper
• Credit cards
• Paper clips
• Staples

What the Shredder Will NOT Shred:

• Continuous forms
• Adhesive labels
• Transparencies
• Newspaper
• CD/DVDs
• Cardboard
• Laminates
• File folders
• X-rays
• Plastic other than noted above

Specifications:

Paper shred size: Cross-Cut: 3.9 x 50mm

*Note: Performance may be reduced with A4 (70g) paper at voltages other than 220-240v, heavier paper, or higher humidity.

Recommended daily usage rates: 10-20 paper passes; 10 cards.

Important Safety Instructions

WARNING:

• Keep away from children and pets. Keep hands away from the paper entry. Always unplug the shredder or set the safety lock when not in use.
• Keep foreign objects such as gloves, jewelry, clothing, and hair away from shredder openings. If an object enters the top opening, switch to Reverse (R) to back out the object.
• Never use aerosol, petroleum-based, or other flammable products on or near the shredder. Do not use canned air on the shredder.
• Do not use the shredder if it is damaged or defective. Do not open the shredder head. Do not place the shredder near or over a heat or water source.
• Feed a maximum of 8 sheets per pass to avoid jams.

CAUTION:

• Avoid touching exposed blades under the Cross-Cut shredder head.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.

Operation

To operate the shredder, the disconnect power switch must be in the ON (I) position. It is recommended to insert a waste bag (Fellowes #36052) for easy disposal.

Note: The shredder runs briefly after each pass to clear the entry. Continuous operation beyond 3-5 minutes will trigger a 15-minute cool-down period.

Shredding Paper

To shred paper:

1. Check the paper amount to ensure it does not exceed the capacity.
2. Set the control switch to Auto-On (I).
3. Feed the paper into the paper entry and release.

Diagram description: Shows feeding paper into the top slot of the shredder with the control switch set to Auto-On (I).

Shredding Credit Cards

To shred credit cards:

1. Set the control switch to Auto-On (I).
2. Hold the credit card at its edge.
3. Feed the card into the center of the paper entry and release.

Diagram description: Shows feeding a credit card into the center of the top slot of the shredder with the control switch set to Auto-On (I).

Safety Lock

The safety lock prevents accidental operation. To set the lock:

1. Wait for shredding to stop.
2. Push the black button down.
3. Slide the button towards the front of the shredder.

To unlock:

1. Push the black button down.
2. Slide the button toward the back of the shredder.

For greater safety, always unplug the shredder after use.

Troubleshooting

Paper Jam

If a paper jam occurs:

1. Set the control switch to Off (0) and unplug the shredder.
2. Remove the shredder head and empty the bin.
3. Replace the shredder head.
4. Follow one or more of the following procedures:
   • Set the control switch to Reverse (R) for 2-3 seconds.
   • Alternate slowly between Forward and Reverse.
   • Gently pull any uncut paper from the paper entry.
5. Plug in the shredder and set the control switch to Auto-On (I) to test.

Shredder Doesn't Start

If the shredder does not start:

• Make sure the shredder head is correctly seated on the basket.
• Wait 15 minutes for the motor to cool down if it has been used continuously.
• Remove and empty the bin if it is full.
• Ensure the safety lock is in the unlock position.

Maintenance

Run the shredder regularly in reverse for one minute to help maintain the cutting blades.

Oiling Procedure:

Follow this procedure and repeat twice:

1. Set the control switch to Off (0) and unplug the shredder.
2. Apply shredder oil across the entry slot.
3. Plug in the shredder and set the control switch to Auto-On (I).
4. Shred one sheet of paper.
5. Set the control switch to Reverse (R) for 2-3 seconds.

Diagram description: Shows applying oil to the shredder entry, then running the shredder in Auto-On mode, and finally running it in Reverse mode.

Lubricate the shredder when the bin is full, or immediately if:

• Capacity decreases.
• The motor sounds different.
• The shredder stops running.

CAUTION: Only use a non-aerosol vegetable oil in a long nozzle container.

Warranty

Fellowes, Inc. provides a limited warranty for this machine. The cutting blades are warranted to be free from defects in material and workmanship for 3 years from the date of original purchase. All other parts are warranted for 2 years from the date of original purchase. If a part is found defective during the warranty period, Fellowes will, at its option, repair or replace the defective part at no charge. This warranty does not cover damage resulting from abuse, mishandling, or unauthorized repair. Any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of the express warranty periods stated above. Fellowes is not liable for any consequential or incidental damages.

This warranty grants specific legal rights, and its terms are valid worldwide, subject to local legal requirements.

For service or warranty details, contact your dealer or Fellowes.

Declaration of Conformity and Contact Information

Fellowes Manufacturing Company, Yorkshire Way, West Moor Park, Doncaster, South Yorkshire, DN3 3FB, England, declares that the product Model P-48C conforms with the requirements of the RoHS Directive (2002/95/EC), the Low Voltage Directive (73/23 EEC), and the Electromagnetic Compatibility Directive (89/336 EEC), along with harmonized European and IEC standards, including EN60950-1/A11:2004 for Safety and EN 61000-3-2/A2:2005, EN 61000-3-3/A1:2001, EN 55014-1/A2:2002, EN 55014-2/A1:2001 for EMC.

This declaration was made in Itasca, Illinois, USA, on June 30, 2006, signed by James Fellowes.

Help Lines:

• Australia: +1-800-33-11-77
• Canada: +1-800-665-4339
• Mexico: +1-800-234-1185
• United States: +1-800-955-0959
• Australia: +61-3-8336-9700
• Benelux: +31-(0)-76-523-2090
• Canada: +1-905-475-6320
• Deutschland: +49-(0)-5131-49770
• France: +33-(0)-1-30-06-86-80
• Italia: +39-071-730041
• Japan: +81-(0)-3-5496-2401
• Korea: +82-2-3462-2884
• Malaysia: +60-(0)-35122-1231
• Polska: +48-(0)-22-771-47-40
• España: +34-91-748-05-01
• Singapore: +65-6221-3811
• United Kingdom: +44-(0)-1302-836836
• United States: +1-630-893-1600

WEEE (Waste Electrical and Electronic Equipment) Information:

This product is classified as Electrical and Electronic Equipment. Please dispose of it in accordance with the European Waste of Electrical and Electronic Equipment (WEEE) Directive and local laws. For more information on the WEEE Directive, please visit www.fellowesinternational.com/WEEE.

Company Information:

Visit the Fellowes website: www.fellowes.com

Company Address: 1789 Norwood Avenue, Itasca, Illinois 60143-1095 USA.

© 2010 Fellowes, Inc. Part No. 402990 REV D