MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NNRH
FLUSH INSET INSTALLATION Allows the refrigerator to be installed flush with adjacent cabinetry
CUSTOM APPEARANCE Allows personalization with cabinet-compatible panels and custom handles
UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Allows precise temperature settings and are positioned for maximum ease of use
HUMIDITY CONTROLLED VEGETABLE COMPARTMENTS AND SEALED SNACK PANS Help maintain freshness and help preserve foods longer
ADJUSTABLE, SPILL PROOF GLASS SHELVES Make it easy to customize storage to handle foods and containers of various sizes
2 SEALED DELI PANS WITH FULL EXTENSION SLIDES
SIX ADJUSTABLE DOOR BINS Offer added storage flexibility
GE WATERTM FILTRATION SYSTEM Delivers clean, great tasting ice
For questions about your appliance, please call 1-800-626-2000.
PAGE 1 OF 17
Product Specification Revised 1/22
SECTION 1 STANDARD INSTALLATION
1/4" FRAMED PANELS
3/4" OVERLAY PANELS
SECTION 2 FLUSH INSET INSTALLATION
REQUIRES ADDITIONAL TRIM KIT ZKFN
For questions about your appliance, please call 1-800-626-2000.
PAGE 2 OF 17
Product Specification Revised 1/22
OVERALL DIMENSIONS
STANDARD INSTALLATION
10"
(25.4)
36" (91.5)
3/4"
(1.9)
25 1/4" (64.1) 23 5/8" (60.0)
73 1/4"
(186.1)
*84"
(213.4)
*83 1/2"
(212.1)
SPECIFICATIONS Overall Width Overall Height Overall Depth Door Clearance Cutout Width Cutout Height
Cutout Depth Plumbing Requirements
Shipping Weight
36" (91.4 cm) 84" (213.4 cm) 25 1/4" (64.1cm) 36 1/2" (92.7 cm) 35 1/2" (90.2 cm) 83 1/2" - 84 1/2" (212.1 - 214.6 cm) 24" (61 cm) 1/4" OD copper tubing or GE SmartConnect kit 640 lb (290 kg)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
FRONT VIEW
*3 5/8"
(9.2)
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
SIDE VIEW
35" (88.9)
Case width
** Allow 25" (63.5) min
clearance for 130° door swing
36 3/4"
(93.3)
TOP VIEW
** 4 9/16" (11.6) min
clearance to a wall for 90° door swing
** Dimensions based on custom handle height of 2 9/16" (6.5).
**These refrigerators are equipped with a 3-position door stop. The factory-set 130° door swing can be adjusted to 90° or 130° for standard installation if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
For questions about your appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
PAGE 3 OF 17
Product Specification Revised 1/22
STANDARD INSTALLATION
TOP VIEW
24" (61) 1 9/16"
(3.97)
7/16" (1.1)
Trim overlap
2 5/16"
(5.874)
35 1/2" (90.2)
A
ELEC.
6"
(15.24)
10"
(25.4)
W SIDE VIEW
3 1/2"
(8.9)
*84 +- .500
(212.1-214.6) *Trim will overlap additional 7/16"
75"
(190.5 ) From floor to bottom of electrical
area
5"
(12.7)
B WATER
3 1/2"
(9.0)
5" 3 1/2"
(12.7) (8.9)
FRONT VIEW
ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two additional hole locations at end
of brackets
CL
Bracket mounted into vertical wall studs centered within the
cutout Ensure holes selected are centered on
the studs
Wall Studs
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
For questions about your appliance, please call 1-800-626-2000.
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
PAGE 4 OF 17
STANDARD INSTALLATION
HELPFUL TIPS
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING:
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
The information below applies to all installation constructions: · A wall bracket, bolts and toggles
will be supplied with the unit. · The bolts will be used to attach
bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. · The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. · In installation opening, measure 81-1/2" from floor and draw a horizontal line. · Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. · The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. · When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied "L" bolts. See Installation Instructions for detailed instructions.
Product Specification Revised 1/22
STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION
A
Grille Panel
B
Fresh
Food Panel
C
PANEL ASSEMBLY CROSS SECTION
Door
Trim
Optional ZKLN kit handle
1/4" Framed Panel
Freezer Drawer Panel D
PANEL DIMENSIONS A
1/4" Framed Panel 33 7/8"
B 8 7/8"
C
D
46 1/16" 21 7/8"
STANDARD INSTALLATION
HELPFUL TIPS
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.
1/4" FRAMED PANELS: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panel 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 11 lbs.
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION
A
PANEL ASSEMBLY CROSS SECTION
Grille Panel
B
Fresh
Food
Panel
C
Door 3/4" Overlay Panel Optional ZKLN kit handle
Trim 1/4" Backer Panel
.10" Spacer Panel
Freezer Drawer Panel D
PANEL DIMENSIONS
1/4" Backer Panel
A 33 7/8"
.10" Spacer Panel
32 1/2"
3/4" Overlay Panel 34 1/8"
B 8 7/8" 7 5/8"
9"
C
D
46 1/16" 21 7/8"
44 11/16" 20 1/2"
46 5/16" 22"
.25" + .10" + .75" = 1.10" Total Panel Thickness
3/4" OVERLAY PANELS: The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panel 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 11 lbs.
DOOR HANDLES: Door panels not included. Custom handles supplied by your cabinet maker may be used
Optional visor handle kit ZKLN available.
For questions about your appliance, please call 1-800-626-2000.
PAGE 5 OF 17
Product Specification Revised 1/22
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*84"
(213.4) *Depending on installation
height
*3"- 4"
(7.6 - 10.2) *Depending on installation
height
2 9/16"
(6.5)
STANDARD INSTALLATION
HELPFUL TIPS
F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
For questions about your appliance, please call 1-800-626-2000.
PAGE 6 OF 17
Product Specification Revised 1/22
DUAL INSTALLATIONS A
2 5/16"
(5.9)
ELEC.
10"
(25.4)
71 1/2" (181.6)
Finished Width
24 3/16" (61.4)
6"
(15.2)
ELEC.
10"
(25.4)
6"
(15.2)
*84 +- .500
(212.1-214.6) Finished Opening
75"
(190.5 ) From floor to bottom of electrical
area
24" (60.9)
Min. Cutout Depth
5"
(12.7)
WATER 3 1/2"
(9.0)
WATER 3 1/2"
5 3/4" 5 3/4" (9.0)
(14.6) (14.6)
5" 3 1/2"
(12.7) (8.9)
FRONT VIEW
10" (25.4) WATER
SIDE VIEW
FSTLAUNSHDAINRDSEITNSINTASTLALLALTAIOTNION
HELPFUL TIPS
A A separate 115V, 60Hz, 15or 20-amp power supply is recommended for each product.
Additional cutout width may be required when side panels are used.
STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
A
°
Grille Panel
°
B
E
Fresh Food Panel
E
Fresh
Food Panel
C
Freezer Drawer Panel Freezer Drawer Panel
D
PANEL ASSEMBLY CROSS SECTION
Door
Trim
Optional ZKLN kit handle
1/4" Framed Panel
PANEL DIMENSIONS
1/4" Framed Panel
A
B
C
D
E
69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.
1/4" FRAMED PANELS: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panel 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 25 lbs.
Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
For questions about your appliance, please call 1-800-626-2000.
PAGE 7 OF 17
Product Specification Revised 1/22
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
A
Grille Panel
B
E
Fresh Food Panel
E
Fresh
Food Panel
C
Freezer Drawer Panel Freezer Drawer Panel
D
PANEL DIMENSIONS
1/4" Backer Panel
.10"
3/4"
Spacer Overlay
Panel Panel
A 69 7/8" 68 1/2" 70 1/8"
B
8 7/8" 7 5/8"
9"
C 46 1/16" 44 11/16" 46 5/16"
D 21 7/8" 20 1/2" 22"
E 33 7/8" 32 1/2" 34 1/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
PANEL ASSEMBLY CROSS SECTION
Door 3/4" Overlay Panel Optional ZKLN kit handle
Trim 1/4" Backer Panel
.10" Spacer Panel
DUAL PRODUCT CLEARANCES
23 7/8" min**
(60.6)
1"
23 7/8" min**
(60.6)
To wall
(2.5)
To wall
** Dimensions based on custom height of 2 9/16" (6.5)
STANDARD INSTALLATION
HELPFUL TIPS
3/4" OVERLAY PANELS: The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panel 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 25 lbs.
Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
DOOR HANDLES: Door handle not included. Custom handles supplied by your cabinet maker may be used.
Optional visor handle kit ZKLN available.
A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required.
130° Door swing
130° Door swing
A
For questions about your appliance, please call 1-800-626-2000.
PAGE 8 OF 17
Product Specification Revised 1/22
OVERALL DIMENSIONS AFTER PANEL INSTALL
FLUSH INSET INSTALLATION
38" (96.5)
11 1/2"
(29.2)
26" (66.0) 20 5/8" (52.4)
* 84 1/2"
(214.6)
*73"
(185.4)
* 83 1/2"
(212.1)
SPECIFICATIONS Overall Width Overall Height Overall Depth Door Clearance Cutout Width Cutout Height Cutout Depth Plumbing Requirements
Shipping Weight
38" (96.5 cm) 84 1/2" (214.6 cm) 25 15/16" (65.9 cm) 38 3/4" (98.4 cm) 39" (99.1 cm) 85" (215.9 cm) 26 3/16" (66.5 cm) 1/4" OD copper tubing or GE SmartConnect kit 640 lb (290 kg)
Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
*26 7/16"
(67.1)
FRONT VIEW
*4"
(10.2)
* Shipping height. Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84"
SIDE VIEW
35" (88.9)
Case width
20 5/8"
(52.5)
** Allow 15" (38.1) min
clearance for 115° door swing
38 3/4"
(98.4)
TOP VIEW
** 4 9/16" (11.6) min
clearance to a wall for 90° door swing
** Dimensions based on custom handle height of 2 9/16" (6.5).
For questions about your appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
PAGE 9 OF 17
Product Specification Revised 1/22
FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET KIT ZKFN REQUIRED
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
85"
(215.9)
Finished cleats
5 1/4" (13.3)
TOP VIEW
Case Finished cleats Case Trim
3/4" Panel
Door
3/4" (1.9)
Width of side cleats
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
ELEC.
6"
(15.2)
10"
(25.4)
24 3/16"
(61.4)
1/2" (1.3)
A
84"
(213.4)
height
to cleat
75 1/2"
(191.8 ) From floor to bottom of electrical
area
W SIDE VIEW
3 1/2"
(8.9)
7"
(17.8)
B WATER
3 1/2"
(9.0)
7" (17.8) 3 1/2"
(8.9)
FRONT VIEW
ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two additional hole locations at end
of brackets
CL
Bracket mounted into vertical wall studs centered within the
cutout Ensure holes selected are centered on
the studs
Wall Studs
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
For questions about your appliance, please call 1-800-626-2000.
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
PAGE 10 OF 17
FLUSH INSET INSTALLATION
HELPFUL TIPS
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING:
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions.
The information below applies to all installation constructions: · A wall bracket, bolts and toggles will
be supplied with the unit. · The bolts will be used to attach bracket to
wall in 4 locations. Two of the locations must penetrate the center of the wall studs. · The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. · In installation opening, measure 82" from floor and draw a horizontal line. · Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. · The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. · When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied "L" bolts. See Installation Instructions for detailed instructions.
WARNING:
Door Trim Pinch Point Hazard
Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
Product Specification Revised 1/22
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
A Grille Panel
PANEL DIMENSIONS
B
A
B
C
D
38" 10 11/16" 46 9/16" 22 7/16"
Fresh
Food Panel
C
Freezer Drawer Panel D
3/4" RAISED DOOR PANEL ROUTING
DETAIL TOP 3/4"
11/32" 1/4"
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
1/4" 7/16"
Front
Back
Back
Front
1/4" DETAIL BOTTOM
CORNER VIEW SHOWING "PICTURE FRAME" ROUTING
DETAIL LEFT SIDE
ROUTER DEPTH 1/4"
2-1/16"
LEFT SIDE
Front
Back 3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
For questions about your appliance, please call 1-800-626-2000.
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4" 2-1/16"
3/32" 1/4"
RIGHT SIDE
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
PAGE 11 OF 17
FLUSH INSET INSTALLATION
HELPFUL TIPS Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel's backs. Additional panel width reductions are required per the diagrams shown. This will create "picture frame' routing allowing the panels to slide into the attached door, drawer and grille trims. MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panels 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 11 lbs NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide. DOOR HANDLES Door handles not included. Custom handles supplied by your cabinet maker may be used. Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
Product Specification Revised 1/22
3/4" RAISED GRILL PANEL ROUTING
DETAIL TOP 1-11/16"
NOTE: Routed areas should be finished as they may be visible when assembled.
Front
Back
TOP
Back
Front
ROUTER DEPTH 1/4"
3/16" DETAIL BOTTOM
LEFT SIDE
DETAIL LEFT SIDE
ROUTER DEPTH 1/4"
2-1/16"
CORNER VIEW SHOWING "PICTURE FRAME" ROUTING
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4" 2-1/16"
3/32" 1/4"
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Front
Back 3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
RIGHT SIDE
3/4" RAISED DRAWER PANEL ROUTING
DETAIL TOP 3/4"
11/32" 1/4" 1/4" 7/16"
NOTE: Routed areas should be finished as they may be visible when assembled.
Front
Back
TOP
Back
Front
1/4" DETAIL BOTTOM
CORNER VIEW SHOWING "PICTURE FRAME" ROUTING
DETAIL LEFT SIDE
ROUTER DEPTH 1/4"
2 1/16"
LEFT SIDE
Front
Back 3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
For questions about your appliance, please call 1-800-626-2000.
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
2 1/16"
RIGHT SIDE
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
PAGE 12 OF 17
FLUSH INSET INSTALLATION
HELPFUL TIPS Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel's backs. Additional panel width reductions are required per the diagrams shown. This will create "picture frame' routing allowing the panels to slide into the attached door, drawer and grille trims. MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panels 58 lbs. · Freezer drawer panel 28 lbs. · Grille panel 11 lbs NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide. DOOR HANDLES Door handles not included. Custom handles supplied by your cabinet maker may be used. Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
Product Specification Revised 1/22
FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET KIT ZKFN REQUIRED
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
5 3/8" (13.7)
TOP VIEW
Case Finished cleats Case Trim
1/2" Panel
Door
3/4" (1.9)
Width of side cleats
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
ELEC.
6"
(15.2)
10"
(25.4)
24 3/16"
(61.4)
1/2" (1.3)
A
85"
(215.9)
Finished cleats
84"
(213.4)
height
to cleat
75 1/2"
(191.8 ) From floor to bottom of electrical
area
W SIDE VIEW
3 1/2"
(8.9)
7"
(17.8)
B WATER
3 1/2"
(9.0)
7" (17.8) 3 1/2"
(8.9)
FRONT VIEW
ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two additional hole locations at end
of brackets
CL
Bracket mounted into vertical wall studs centered within the
cutout Ensure holes selected are centered on
the studs
Wall Studs
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
For questions about your appliance, please call 1-800-626-2000.
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
PAGE 13 OF 17
FLUSH INSET INSTALLATION
HELPFUL TIPS
A Mounting the junction box in this location will also allow for front accessibility through access panel.
B Water supply area.
WARNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
The information below applies to all installation constructions: · A wall bracket, bolts and toggles
will be supplied with the unit. · The bolts will be used to attach
bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. · The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. · In installation opening, measure 82" from floor and draw a horizontal line. · Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. · The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. · When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied "L" bolts. See Installation Instructions for detailed instructions.
Product Specification Revised 1/22
FLUSH INSET 1/2" PANEL DIMENSIONS
A
Grille Panel
B
Fresh
Food Panel
C
PANEL DIMENSIONS
1/4" Backer Panel .10" Space Panel 1/2" Overlay Panel
A 33 7/8" 32 1/2"
38"
B
C
8 7/8" 46 1/16"
7 5/8" 44 11/16"
10 11/16" 46 9/16"
D 21 7/8" 20 1/2" 22 7/16"
Freezer Drawer Panel D
1/2" OVERLAY PANEL ROUTING DIMENSIONS
C Hinge Side
Door Panel Back
Grille Back C
A
B
D
Backer with Overlay Panel Assembly
C Freezer Drawer
FLUSH INSET INSTALLATION
HELPFUL TIPS
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
ASSEMBLE THE PANELS WITH GLUE AND SCREWS: · Center the spacer panel on the
backer panel, left to right and top to bottom. Secure the panels with glue.
· Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
A
B
D
A
B
D
Door
1/2" Overlay Panel
1/4" Backer Panel
.10" Spacer
For questions about your appliance, please call 1-800-626-2000.
PANEL DIMENSIONS
Fresh Food Panel Freezer Panel Grille Panel
A
B
C
D
2 1/16" 2 1/16" 5/16" 3/16"
2 1/16" 2 1/16" 5/16" 3/16"
2 1/16" 2 1/16" 1 11/16" 3/16"
PAGE 14 OF 17
Product Specification Revised 1/22
3/4" OR 1/2" DUAL INSTALLATIONS
4 5/16"
(10.9)
75" (190.5)
A Finished Width
24 3/16" (61.4)
ELEC.
5 1/2"
(13.9)
ELEC.
5 1/2"
(13.9)
9"
(22.9)
9"
(22.9)
85"
(215.9) Finished Opening
75 1/2"
(191.8 ) From floor to bottom of electrical
area
26 3/16" (66.5)
Min. Cutout Depth
7"
(17.8)
WATER 3 1/2"
(9.0)
WATER 3 1/2"
7 1/2" 7 1/2" (9.0)
(19.1) (19.1)
7" 3 1/2"
(17.8) (8.9)
FRONT VIEW
3 1/2"
(8.9)
W
SIDE VIEW
FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION
A
° Grille Panel
°
B
Fresh Food Panel
E
Fresh
Food Panel
C
Freezer Drawer Panel Freezer Drawer Panel
D
PANEL DIMENSIONS
1/4" Backer Panel .10" Space Panel 1/2" Overlay Panel
A
B
C
D
E
69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"
68 1/2" 7 5/8" 44 11/16" 20 1/2" 32 1/2"
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
For questions about your appliance, please call 1-800-626-2000.
PAGE 15 OF 17
FLUSH INSET INSTALLATION
HELPFUL TIPS
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel's backs. Additional panel width reductions are required per the diagrams shown. This will create "picture frame' routing allowing the panels to slide into the attached door, drawer and grille trims.
A A separate 115V, 60Hz, 15or 20-amp power supply is recommended for each product.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panels 58 lbs. · Freezer drawer panel 28 lbs. · Unified grille panel 25 lbs
DOOR HANDLES Door handles not included. Custom handles supplied by your cabinet maker may be used.
Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side. The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
ASSEMBLE THE PANELS WITH GLUE AND SCREWS: · Center the spacer panel on the
backer panel, left to right and top to bottom. Secure the panels with glue. · Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Product Specification Revised 1/22
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
A Grille Panel
Fresh Food Panel
E
Fresh Food Panel
PANEL DIMENSIONS
B
A
B
C
D
E
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
C
Freezer Drawer Panel Freezer Drawer Panel
D
3/4" RAISED DOOR AND DRAWER PANEL ROUTING (SEE PAGE 11 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)
DETAIL TOP
3/4"
NOTE: Routed areas should
TOP
11/32" 1/4"
be finished as they may be visible when assembled.
1/4" 7/16"
Front
FLUSH INSET INSTALLATION
HELPFUL TIPS
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel's backs. Additional panel width reductions are required per the diagrams shown. This will create "picture frame' routing allowing the panels to slide into the attached door, drawer and grille trims.
MAXIMUM TOTAL PANEL WEIGHT: · Fresh food door panels 58 lbs. · Freezer drawer panel 28 lbs. · Unified grille panel 25 lbs
DOOR HANDLES Door handles not included. Custom handles supplied by your cabinet maker may be used.
Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed sideby-side.
3/16" DETAIL BOTTOM
Back
CORNER VIEW SHOWING "PICTURE FRAME" ROUTING
Back
Front
DETAIL HINGE SIDE
ROUTER DEPTH 1/4"
2 1/16"
HINGE SIDE
Front
Back 3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
For questions about your appliance, please call 1-800-626-2000.
DETAIL HANDLE SIDE
3/16"
HANDLE SIDE
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
PAGE 16 OF 17
Product Specification Revised 1/22
3/4" OR 1/2" DUAL PRODUCT CLEARANCES
16 7/8" (42.9) min**
1"
16 7/8" (42.9) min**
To wall
(2.5)
To wall
** Dimensions based on custom handle height of 2 9/16"
115° Door swing
115° Door swing
A
FLUSH INSET INSTALLATION
HELPFUL TIPS
A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.
For questions about your appliance, please call 1-800-626-2000.
PAGE 17 OF 17
Product Specification Revised 1/22
Adobe PDF Library 16.0 Adobe InDesign 16.4 (Macintosh)
Monogram Refrigerator Installation Instructions & Design Guide Comprehensive installation guide and design specifications for Monogram Fresh-Food Refrigerators (ZIFI240, ZIFS240) and Bar Refrigerators with Icemaker (ZIBI240, ZIBS240). Includes safety information, electrical connections, water line installation, design clearances, and step-by-step installation procedures.
