Monogram Refrigerator Installation Instructions & Design Guide

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

ℹ️ IMPORTANT: Save these instructions for local inspector's use. Observe all governing codes and ordinances.

ℹ️ Note to Installer: Be sure to leave these instructions with the Consumer.

ℹ️ Note to Consumer: Keep these instructions with your Owner's Manual for future reference.

If you received a damaged refrigerator, you should immediately contact your dealer or builder.

Skill Level: Installation of this refrigerator requires basic mechanical, carpentry, and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner's Manual for warranty information.

? WARNING: Explosion Hazard. Keep flammable materials and vapors away from refrigerator. Failure to do so can result in fire, explosion, or death.

⚠️ WARNING: To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product.

For Monogram local service in your area, call 800.444.1845 or visit monogram.com.

For Monogram service in Canada, call 888.880.3030.

For Monogram Parts and Accessories, call 800.444.1845 or visit monogram.com.

For Monogram Parts and Accessories in Canada, call 888.880.3030 or visit monogram.ca.

CONNECTING ELECTRICITY

⚡ WARNING: Electrical Shock Hazard.

• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not use an adapter.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Immediately discontinue use of a damaged supply cord. If the supply cord is damaged, it must be replaced by a qualified service professional with an authorized service part from the manufacturer.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

Important Information & Preparation

? WARNING: CUT HAZARD. Cabinet edges along stamp/cut-out areas may be sharp. Avoid placing hands, fingers, or other appendages near these areas. Failure to do so can result in cuts.

? AVERTISSEMENT: Risque de coupure. Les bords de la caisse et les zones comportant un code d'identification ou des découpes peuvent être tranchants. Garder les mains, les doigts ou autres appendices éloignés de ces zones. Le non-respect de cette instruction peut causer des coupures.

Parts Required

For ZIFI240 and ZIBI240 Models Only:

• Custom handle
• Assembled overlay panel
• Screws

Parts Supplied (General):

• Handle side trim
• Black or Stainless Steel Toekick Options: These products are shipped with a stainless steel toekick and a black toekick. For shipping purposes, one of the toe kicks will be secured to the back of the unit, and the second will be installed on the unit. Keep the unused toekick and any unused parts for future use.

Tools/Hardware Required

• Adjustable wrench
• Carpenter's glue (ZIFI240 and ZIBI240 models only)
• Screwdriver

Staining Wood Panel Fronts

The drawer fronts are unfinished cherry wood. During use, oil from hands may accumulate and stain the wood.

• The drawer fronts may be stained and sealed to match adjacent cabinetry.
• Apply the stain and sealer according to the manufacturer's instructions. To avoid unpleasant odor, keep the door open to ventilate and allow the stain/sealer to dry completely before using the product.

Caring for Your Stainless Steel

Before installation or first use, we strongly advise that you polish the stainless steel exterior and handle with a commercially available stainless steel cleaner such as Stainless Steel Magic.™ To preserve and protect the fine finish, we also strongly advise that you apply stainless steel cleaner monthly.

Refrigerator Location

• Do not install the refrigerator/freezer where the temperature will go below 55°F (13°C). It will not run often enough to maintain proper temperatures.
• Do not install the refrigerator/freezer where temperatures will go above 100°F (37°C). It will not perform properly.
• Do not install the refrigerator/freezer in a location exposed to water (rain, etc.) or direct sunlight.
• Install it on a floor strong enough to support it fully loaded.

ℹ️ NOTE: GFCI (ground fault circuit interrupter) is not recommended.

• Products must operate from separate, properly grounded receptacles.

INSTALL WATER LINE

(ZIBI240 AND ZIBS240 MODELS ONLY)

⚠️ WARNING: Connect to potable water supply only.

⚠️ AVERTISSEMENT: Raccordez l'appareil à une alimentation d'eau potable seulement.

• A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 p.s.i. (137-827 kPa).
• The water line can enter the opening through the floor or back wall. Route 1/4" O.D. copper tubing or SmartConnect™ kit between the cold water line and water connection location, long enough to extend to the front of the refrigerator.
• Install an optional water filter in the water line near the refrigerator. A water filter is recommended in areas where the water supply contains sand and particles. Installation Instructions are packed with the filter.

ℹ️ NOTE: The only GE approved plastic tubing is supplied in the SmartConnect™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home.

SmartConnect™ Refrigerator Tubing Kits are available in the following lengths:

• 2' (0.6 m)...WX08X10002
• 6' (1.8 m)...WX08X10006
• 5' (4.6 m)...WX08X10015
• 25' (7.6 m)...WX08X10025

Shut off the main water supply. Turn on the nearest faucet long enough to clear the line of water.

• Install a shut-off valve (required) between the icemaker water valve and cold water pipe in a basement or cabinet. The shut-off valve should be located where it will be easily accessible.
• Turn on the main water supply and flush debris. Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.

ℹ️ NOTE: Saddle type shut-off valves are included in many water supply kits, but are not recommended for this application.

Diagram: Water line connection showing measurements for water line, shaded area, floor, and minimum distance.

ℹ️ NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

INSTALLATION OPTIONS

All models may be installed in any of these options using the installation design guide provided. Note the descriptions below:

FREESTANDING

The product will have no cabinet around it and no countertop above it.

SINGLE STANDARD

The product will be installed inside a cabinet opening, a countertop will be above it and the door face will NOT be flush with the adjacent cabinets.

SINGLE FLUSH INSET (NOT FULLY INTEGRATED)

The product will be installed inside a cabinet opening, a countertop will be above it and the door face WILL BE FLUSH with the adjacent cabinets.

SIDE-BY-SIDE (DUAL) INSTALLATIONS

For a complete refreshment center, other undercounter products can be installed side by side. Please refer to the specific products and the dual design guide chart for the desired installation configuration requirements. The pair can be Standard or Flush Inset installed, both units need to match install type.

Design Guide: The Installation Space

For models ZIFI240, ZIFS240, ZIBI240, ZIBS240

SINGLE PRODUCT INSTALLATION

Diagram: Shows single product installation space with labels F, A, G, I, N, O, J, K, P. Includes notes on waterline location and custom handles.

SIDE BY SIDE PRODUCT INSTALLATION

Diagram: Shows side-by-side product installation space with labels D, H, E, B, C, N, O, P, L, M. Includes notes on custom handles.

Dimensions Table

Standard Installation

Diagram: Illustrates standard installation for single and dual units, showing hinge filler (T), middle filler (U), and product forward of flush (V) measurements (2" or 1"). Includes angles (110°, 120°) and cabinet/product case references.

ℹ️ NOTE: ALL Fillers should be located 1 5/8" back from the front face of the cabinetry or located even with the front edge of the product case behind the gasket.

Flush Inset Installation

Diagram: Illustrates flush inset installation for single and dual units, showing hinge filler (T), middle filler (U), and product flush (V) measurements (e.g., 1 1/8", 1/4", 0"). Includes angles (110°, 120°) and cabinet/product case references.

ℹ️ NOTE: ALL Fillers should be located 1 5/8" back from the front face of the cabinetry or located even with the front edge of the product case behind the gasket.

Design Guide: Product Clearances

The door swing opening angles from the factory are set at 110° for models ZIFI240, ZIFS240, ZIBI240, and ZIBS240 with no adjustment or stop at 90°.

Choose the location:

• These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door.
• Do not install these products where the temperature will go below 55°F (13°C) or above 100°F (37°C).
• These products are not designed to be stacked one over the other.
• Right hand models illustrated. Allow the same clearances on the opposite side for left hand models.
• Test the door swing. Carefully open and close the door. The door should not rub or catch on adjacent cabinetry.

When installing custom panel and handle, use clearances as a general guide but adjust according to the specific installation.

Clearance Distances Chart

When installing in a corner or near a wall, note the recommended clearance distances in the following chart:

ℹ️ NOTE: Clearances are based on the recommended maximum 2 9/16" (65mm) handle height.

Diagram: Illustrates minimum wall clearances (W, X) for 110° and 90° door swings, showing dimensions B, R, and F.

Installation Instructions

STEP 1: REMOVE PACKAGING AND INSTALLATION PARTS

• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective plastic coverings.
• Remove the toekick attached to the back of the unit.
• Remove the custom panel attached to the front of the unit.

⚠️ WARNING: Small objects are a choke hazard for children. Remove and discard any parts not used.

⚠️ AVERTISSEMENT: Les petits objects peuvent étrangler les enfants. Il faut jeter toutes les pièces qui ne sont pas utilisées.

STEP 2: REVERSING THE DOOR (ZIFI240 model only)

⚠️ WARNING: Follow all steps when reversing the door swing. Failure to follow these instructions, leaving off parts, or over tightening screws, can lead to the door falling off and result in injury and property damage.

⚠️ AVERTISSEMENT: Suivez toutes les étapes pour inverser le sens d'ouverture de porte. L'omission de suivre ces instructions, de ne pas utiliser toutes les pièces, ou le serrage excessif des vis, peuvent causer la chute de la porte et occasionner des blessures ou des dommages à la propriété.

• Remove top hinge and discard. Hold the door in place.
• Remove the black screw-hole cover from top left of cabinet and insert in top right.
• Remove 4 screws to remove the top door trim (do NOT discard).
• Remove the top hinge pin (do NOT discard).
• Flip the door 180 degrees.
• Remove 3 screws to remove the bottom door trim (do NOT discard).
• Remove 2 screws to remove the door stop and discard door stop.
• Remove 1 screw to remove the bottom hinge pin and discard hinge pin.

ℹ️ NOTE: Make sure the door is upside down so what was the bottom is now the top.

• Insert the top hinge pin.
• Remove the top trim cover and discard.
• Install top door trim onto the new top side of the door.
• Install the new top trim cover that snaps into place.
• Flip the door 180 degrees.

STEP 2: REVERSING THE DOOR (Cont.) (ZIFI240 model only)

• Install the new left bottom hinge pin and new door stop that are enclosed in the hardware bag.
• Install the bottom trim onto the new bottom side of the door.
• Remove 2 screws to remove the toe kick (do NOT discard).
• Remove 4 screws to remove the bottom right hinge (discard the hinge).
• Install bottom left hinge that is enclosed in hardware bag with existing screws.

STEP 2: REVERSING THE DOOR (Cont.) (ZIFS240 model only)

⚠️ WARNING: Follow all steps when reversing the door swing. Failure to follow these instructions, leaving off parts, or over tightening screws, can lead to the door falling off and result in injury and property damage.

⚠️ AVERTISSEMENT: Suivez toutes les étapes pour inverser le sens d'ouverture de porte. L'omission de suivre ces instructions, de ne pas utiliser toutes les pièces, ou le serrage excessif des vis, peuvent causer la chute de la porte et occasionner des blessures ou des dommages à la propriété.

• Remove top hinge and discard. Hold the door in place.
• Remove the black screw-hole cover from top left of cabinet and insert in top right.
• Remove 2 screws to remove the toekick (do not discard).
• Remove the plastic cap from the top left corner of the toe kick and discard.
• Attach the new plastic cap that is enclosed in the hardware bag to the top right corner of the toe kick.
• Reinstall toe kick to unit with 2 existing screws.
• To install the door, set the door onto the left bottom hinge pin. Holding the door in place, insert the new top left hinge pin into the door and secure the hinge to the case with screws.
• Remove bottom right hinge and discard the hinge. Keep the screw for installation of the new hinge.
• Attach the bottom left hinge with the screw from the previous step.

STEP 2: REVERSING THE DOOR (Cont.) (ZIFS240 model only)

• Move the plug on the toekick from the left to the right and reattach toekick to the unit.
• Insert the new top plug/bushing in the new top of the door.
• Remove top plug/bushing from the door using a flat head screwdriver. Discard the bushing.
• Rotate the door 180°.
• Re-insert the black screw post in the new bottom of the door.
• Rotate the door 180°.
• Remove the screw from the plug/bushing on the bottom of the door. Discard the plug/bushing but keep the screw.
• Insert the new bottom plug/bushing in the new bottom of the door. Secure with the screw removed from the old plug/bushing.
• Remove the black screw post from the bottom of the door using a flat head screwdriver. Keep the screw post.

ℹ️ NOTE: The top will now be the bottom of the door and the bottom is now the top.

• To install the door, set the door onto the left bottom hinge pin. Holding the door in place, insert the new top left hinge pin into the door and secure the hinge to the case with screws.

STEP 3: INSTALL CUSTOM 3/4" DOOR PANEL AND HANDLE (ZIFI240 and ZIBI240 models only)

3/4" Overlay Panel Dimensions

Model ZIFI240 and ZIBI240 require a field-installed overlay door panel.

• The overlay panel must be secured to a 1/4" thick backer panel that slides into the trim. A .10" thick spacer panel must be placed between the overlay and backer panel.
• A custom handle of your choice, supplied by your cabinetmaker, must be installed on this overlay panel. Countersink all screws into the backer panel. Screws cannot protrude from the backer panel.

IMPORTANT NOTE: Maximum total weight for custom door panel is 25 pounds.

3/4" Overlay Panel Dimensions (in inches)

Diagram: Shows the relationship between Door, Overlay Panel, Backer Panel, and Spacer Panel with dimensions.

Assemble overlay panels with glue and screws.

• Center spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
• Center the spacer/backer panel on the overlay panel. Secure with glue and screws. Countersink all screws into the backer panel.

Diagram: Shows the assembled overlay panels (Overlay Panel, Spacer Panel, Backer Panel).

Custom Panel Hinge Routing Dimensions

Use a 3/4" router bit to cut a notch into the back side of the assembled panel 3/8" toward the front of the overlay panel, 3/4" deep and 7/8" wide.

Diagram: Shows custom panel hinge routing dimensions (3/4" deep, 7/8" wide, 3/8" from front).

ℹ️ NOTE: Right-hand models illustrated. Cut notches on the opposite side for left-hand fresh food door swing models ZIFI240 and ZIFS240.

Install custom door panel and handle:

• Open door to 90°.
• Remove 5 screws holding trim; lift off trim. Retain screws.

ℹ️ NOTE: Right-hand models illustrated. Follow the same instructions on the opposite side for left-hand fresh food door swing models ZIFI240 and ZIFS240.

• Slide overlay panel into the door trim.
• Reinstall the side trim using the trim screws removed earlier.
• Place the brushed decorative cover over the side trim to hide the screw heads. Ensure side trim is aligned top to bottom and front to back. Snap into place.

ℹ️ NOTE: For shipping purposes, the brushed decorative cover will be secured to the front of the unit.

STEP 3: INSTALL CUSTOM 3/4" DOOR PANEL AND HANDLE (Cont.)

Diagram: Shows custom door panels and handle, with screws needing to be countersunk.

STEP 4: LEVEL

• Use an adjustable wrench to turn the leveling legs and raise or lower the product. For built-in installation, adjust the leveling legs slightly below the bottom of the countertop.

INSTALLATION TIP:

Measure floor to underside of countertop inside the opening. If the room floor is higher than the opening floor, adjust the rear leveling legs approximately 1/8" less than the opening height. Screw front legs all the way in to shorten the height at the front. This will allow you to slightly tip the unit into the opening. Once in the correct position, the front legs can be adjusted to level the product.

Diagram: Shows adjusting leveling legs, with text indicating "Turn Right to Lower" and "Turn Left to Raise".

STEP 5: CONNECT WATER SUPPLY (ZIBI240 and ZIBS240 models only)

⚠️ WARNING: Connect to potable water supply only.

⚠️ AVERTISSEMENT: Raccordez l'appareil à une alimentation d'eau potable seulement.

⚡ WARNING: Electrical Shock Hazard

Attach tubing clamp using existing hole only. DO NOT drill into the refrigerator.

⚡ AVERTISSEMENT: RISQUE DE DÉCHARGE ÉLECTRIQUE. Fixez le collier de serrage dans le trou présent seulement. NE PERCEZ PAS dans le réfrigérateur.

• Locate and bring the water line tubing to the rear of the cabinet.
• Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the water.

Copper Tubing:

• Slip a 1/4" nut and ferrule over both ends of the copper tubing. Insert the tube into the refrigerator connection on the unit and tighten the nut.
• Turn on the water to check for leaks.

GE SmartConnect™ Tubing:

• Follow the instructions provided with the tubing. Over tightening may cause leaks. Turn on the water to check for leaks.

ℹ️ NOTE: Coil excess tubing behind the unit.

Installation Instructions (Continued)

STEP 6: CONNECT POWER

• Connect power cord plug to a properly grounded receptacle.
• Check to make sure power is on by opening the door to see if interior light turns on.
• Bar Refrigerator with Icemaker: The interior fan runs all the time except during defrost cycle when the door is open.
• Fresh-Food Refrigerator: The interior fan runs all the time except when the door is open.

See the Owner's Manual for further explanation of the fan.

STEP 7: SLIDE PRODUCT INTO THE CUTOUT

ℹ️ NOTICE: Do not push against the door panel with your knees. Do not push or lift the unit by the door handle. Damage may occur.

• Open the door and gently push the unit back into the opening with your hands against the sides. Be careful not to entangle power cord.
• In a standard 24" opening, the front face of the stainless steel door will be flush with adjacent cabinetry. A custom panel door may protrude 1-3/4" beyond the surrounding cabinets.
• Check again to be sure the unit is level.
• If the unit is installed under a countertop, adjust the leveling legs until the unit is resting firmly against the underside of the countertop.
• If alignment with adjacent cabinetry is an issue, use a shim to secure the unit against the underside of the countertop.

STEP 8: SET TEMPERATURE CONTROLS

• The temperature controls are preset. Refer to the Owner's Manual for more information. Allow 12-24 hours for the temperature to stabilize.

ℹ️ NOTE: The Fresh-Food Refrigerator or Bar Refrigerator with Icemaker operate very quietly. You may not notice the unit running, and when first installed, the fans and motor may not come on immediately – this is normal. If the display is lit and the light is working, the unit is operating.

Additional Notes

ℹ️ NOTE: While performing installations described in this book, safety glasses or goggles should be worn.

ℹ️ NOTE: Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice.