Pure & Easy Assembly Instructions
Model Numbers: FTBFVT-6049, FTBFVT-6050
Version: PYJS-V2
NOTICE
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Assembly Tips:
- Assemble on a flat, clean, and soft surface.
- Professional installation is highly recommended.
- Periodically check that all components are tightly secured.
Assembly Recommendation
It is recommended that multiple people assemble this product.
Auxiliary Tools Required:
- Electric Drill
- Hammer
- Tape Measure
- Utility Knife
- Safety Helmet
Using Cam Lock and QuickFit
Tightening QuickFit: Tighten QuickFit until the shoulder is flush with the panel. Do not overtighten or undertighten.
Fitting Cam Lock: When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit.
Securing Cam Lock: The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten.
Safety Warnings
Never let children climb or hang on drawers, doors, or shelves.
Furniture Tip-Over Warning: Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints.
Parts List
The following components are included:
| Item No. | Reference Image Description | Qty. |
|---|---|---|
| 1 | Long, flat panel with grooves and holes | X1 |
| 2 | Side panel with holes | X1 |
| 3 | Side panel with holes | X1 |
| 4 | Rectangular panel with holes | X1 |
| 5 | Rectangular panel with holes | X1 |
| 6 | Rectangular panel with holes | X1 |
| 7 | Long, thin panel with holes | X2 |
| 8 | Long, thin panel with holes | X1 |
| 9 | Long, thin panel with holes | X1 |
| 10 | Large rectangular panel with a recessed area | X1 |
| 11 | Long, thin panel with holes | X1 |
| 12 | Drawer runner component | X2 |
| 13 | Long, thin panel with holes | X1 |
| 14 | Long, thin panel with holes | X2 |
| 15 | Long, thin panel with holes | X2 |
| 16 | Long, thin panel with holes | X1 |
| 17 | Rectangular panel with holes | X1 |
| 18 | Long, thin panel with holes | X1 |
| 19 | Long, thin panel with holes | X1 |
| 20 | Rectangular panel with holes | X1 |
| 21 | Rectangular panel with holes | X1 |
| 22 | Small connector pieces | X4 |
| 23 | Small shelf or divider | X1 |
| 24 | Rectangular panel with holes | X1 |
| 25 | Long, thin panel with holes | X1 |
| A | Screws (ST3.5*12mm) | X60 |
| B | Cam lock fittings | X60 |
| C | Cam lock dowels | X20 |
| D | Wooden dowels | X3 |
| E | Screws (5/32x20mm) | X3 |
| F | Hinges | X2 |
| G | Screws (ST3.5*12mm nickel color) | X12 |
| H | Screws (ST3.5*12mm) | X24 |
| I | Screws (ST4*30mm) | X8 |
| J | Truss Head screws (ST3.5*12mm) | X2 |
| K | Plastic corner brackets | X6 |
| L | Plastic caps/covers | X4 |
| M | Drawer handle mechanism | X1 |
| N | Power adapter/cable | X1 |
| O | Power strip/connector | X1 |
| P | Cable management clip | X1 |
| Q | Drawer runners (inner/outer) | X4 sets |
| R | Mirror support bracket | X1 |
| S | Mirror support bracket | X1 |
| T1 | LED light strip connector | X2 |
| T2 | LED light strip | X2 |
| T3 | LED light strip connector | X2 |
| T4 | LED light strip connector | X2 |
Exploded View
A diagram shows all parts laid out and numbered, indicating how they will connect to form the final vanity desk structure.
Assembly Steps
Step 1
Attach part A (6 pcs) and part C (1 pc) to part Q1 (1 pc) using screws H (2 pcs). Ensure alignment with the mounting hole of the guide rail.
Step 2
Attach part A (4 pcs) and part C (2 pcs) to part Q1 (1 pc) and part 3 (1 pc) using screws H (2 pcs).
Step 3
Attach part A (6 pcs) and part C (1 pc) to part Q1 (1 pc) and part 3 (1 pc) using screws H (2 pcs). Ensure alignment with the mounting hole of the guide rail.
Step 4
Attach part A (4 pcs) and part C (2 pcs) to part Q1 (1 pc) and part 4 (1 pc) using screws H (2 pcs).
Step 5
Attach part 5 (1 pc) and part 6 (1 pc) to part 3 using 8 pieces of part B.
Step 6
Attach part 7 (2 pcs) and part 8 (1 pc) to parts 2, 3, and 4 using 12 pieces of part B.
Step 7
Attach part 9 (1 pc) to the assembled structure.
Step 8
Attach part 1 (1 pc) to the structure using 16 pieces of part A and 8 pieces of part C.
Step 9
Secure part 1 using 8 pieces of part B.
Step 10
Attach part 1 to the structure using 6 pieces of part H and 6 pieces of part K.
Step 11
Attach part 10 (1 pc) to the back of the structure using 8 pieces of part A and 4 pieces of part C.
Step 12
Assemble parts 11 (1 pc), 12 (2 pcs), and 25 (1 pc) using parts A (4 pcs), C (2 pcs), and B (4 pcs).
Step 13
Attach parts 11, 12, 25, and 10 to the main structure using 8 pieces of part B.
Step 14
Attach part 10 to the main structure using 8 pieces of part B.
Step 15
Assemble parts 13, 14, 15, 16, and 17 using parts A (4 pcs), B (4 pcs), D (1 pc), E (1 pc), I (4 pcs), and other numbered parts.
Step 16
Attach drawer runners (Q2, 2 pcs) to part 13 (1 pc) using screws H (4 pcs).
Step 17
Assemble parts 14 (1 pc), 15 (1 pc), 18 (1 pc), 19 (1 pc), and 20 (1 pc) using parts A (8 pcs) and I (4 pcs).
Step 18
Assemble parts 19 (1 pc), 21 (1 pc), 14 (1 pc), 18 (1 pc), 15 (1 pc) using parts B (8 pcs), H (4 pcs), D (1 pc), E (1 pc), and Q2 (2 pcs).
Step 19
Attach 4 pieces of part 22 to the drawer assembly.
Step 20
Insert the assembled drawer into the vanity desk, connecting it with part 13 and part 18.
Step 21
Attach part 23 (1 pc) to the vanity desk using 4 pieces of part L.
Step 22
Attach hinges (F, 2 pcs) and part 24 (1 pc) to the vanity desk using parts D (1 pc), E (1 pc), and G (4 pcs).
Step 23
Attach part 24 (1 pc) to the vanity desk using 8 pieces of part G.
Step 24
Place mirror support brackets R (1 pc) and S (1 pc) onto the vanity desk.
Step 25
Attach the mirror assembly using parts O (1 pc), P (1 pc), H (2 pcs), and J (2 pcs).
Step 26
Connect the power adapter/cable (N, 1 pc) to the power strip/connector (O) and the vanity's lighting system.
Step 27
Install the smart LED light mirror. The mirror has an LED light adjustable in 3 colors (Cold, Natural, Warm). A short press changes the color, and a long press adjusts the brightness. Use parts T1, T2, T3, T4 for installation.
Step 28
Installation Completed.
Help Center
If you encounter any difficulties during assembly, please contact us.
- Inquiry
- Assembly Issue
- Missing Parts
Disclaimer
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
