IKEA BESTÅ TV Stand Assembly Instructions

Important Safety Information

⚠️ WARNING! Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

This warning is also provided in multiple languages: Deutsch, Français, Nederlands, Dansk, Íslenska, Norsk, Suomi, Svenska, Čeština, Español, Italiano, Magyar, Polski, Eesti, Latviešu, Lietuvių, Portugues, Româna, Slovensky, Български, Hrvatski, Ελληνικά, Українська, Srpski, Slovenščina, Türkçe, 中文, 한국어, 日本語, Bahasa Indonesia, Bahasa Malaysia, عربي, ไทย.

Parts Included

The following parts are included in the package. Quantities are indicated:

• Allen key: 1x (Part number: 100006)
• Screws: 12x (Part number: 130618)
• Cam lock fittings: 8x (Part numbers: 118137, 122971, 141028, 130725, 119253)
• Cam lock fittings: 4x (Part numbers: 130619, 130722, 141027, 130723, 130620)
• Brackets: 4x (Part number: 144342)
• Brackets: 3x (Part number: 103693)
• Brackets: 3x (Part numbers: 144343, 144344, 144345, 144346, 144347)
• Feet/Legs: 6x (Part numbers: 114947, 115988)
• Shelf supports: 8x (Part numbers: 109049, 113287, 116637)
• Sliding rails/supports: 2x (Part numbers: 133209, 133210, 133212, 133211, 133208, 10093085)
• Support rail: 1x (Part numbers: 133203, 133204, 133205, 133207, 133206, 10093227)
• Support rail: 1x (Part numbers: 144567, 144568, 144569, 144570, 144571, 10093069)
• Brackets: 4x (Part numbers: 115444, 115443)
• Brackets: 2x (Part numbers: 144348, 144349, 144350)

Note: Screws and wall plugs for wall attachment are not included and must be purchased separately, suitable for your wall type.

Assembly Steps

Step 1: Attach Feet

Place two large base panels on a protected surface. Attach 6 feet to the underside of these panels using screws. The feet are adjustable.

Visual: Two large panels are shown flat. Six feet are being screwed into the bottom of each panel.

Step 2: Assemble Main Frame

Connect the side panels to the base panels. Insert 12 screws and use cam lock fittings to secure them. Ensure correct orientation of panels.

Visual: Side panels are being attached to the base panels. Close-ups show screws and cam locks being used.

Step 3: Install Internal Dividers

Insert the vertical internal divider panels into the designated slots on the base panels. Secure them with screws and cam locks.

Visual: Vertical divider panels are inserted into the base and secured.

Step 4: Attach Top Panel

Place the top panel onto the assembled frame. Secure it using the provided screws and cam lock fittings.

Visual: The top panel is placed on the structure and secured.

Step 5: Install Internal Brackets

Attach 4 internal brackets to the inside surfaces of the unit. These are likely for supporting shelves or sliding mechanisms.

Visual: Four brackets are screwed into the inner sides of the unit.

Step 6: Install Sliding Mechanisms/Supports

Install the sliding rails or supports (2x) and other support structures (1x each) as shown. These are crucial for the functionality of shelves or doors.

Visual: Metal rails and support pieces are attached to the interior of the unit.

Step 7: Connect Sections

Join the assembled sections together, likely using screws and cam locks as indicated.

Visual: Different parts of the unit are being connected.

Step 8: Install Shelves & Cable Management

Insert shelves using the shelf supports (8x). Route cables through the designated openings and channels.

Visual: Shelves are placed on supports. Cables are shown being fed through the unit.

Step 9: Attach Wall Mounting Brackets

Secure the wall mounting brackets (various quantities shown across steps) to the back of the unit using screws.

Visual: Wall mounting brackets are being attached to the back of the assembled unit.

Step 10: Wall Mounting Preparation

Hold the unit against the wall at the desired height. Mark the wall through the bracket holes. Drill holes and insert appropriate wall anchors (not included).

Visual: A person is shown marking the wall. Another shows drilling holes.

Step 11: Secure Unit to Wall

Align the unit's brackets with the wall anchors. Use suitable screws (not included) to securely fasten the unit to the wall.

Visual: The unit is being screwed to the wall via the brackets.

Step 12: Final Checks & UPPLEVA Accessory

Ensure all connections are tight. The UPPLEVA system is mentioned for TV mounting or additional wall securing, and it is noted that UPPLEVA is not available in all countries.

Visual: Diagrams show the UPPLEVA accessory booklet and its use in mounting a TV or securing the unit.