FOXEER Predator Nano FPV Camera

Important Information

⚠️ WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property, and cause serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

ℹ️ NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. FOXEER disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

SUPPORT: Visit www.foxeer.com for more information.

Connections

5-Pin Harness Description

The 5-pin harness includes the following connections:

VCC: 4.5-20V DC input (Red wire)
VID: Video output (Yellow wire)
GND: Ground (Black wire)
VSEN: Voltage Sense (Blue wire) - Connect this cable where you want to detect the voltage.
OSD: OSD control (White wire)

Camera-Video Transmitter Connection

To connect the camera directly to the video transmitter, plug the 3-pin wiring harness from the video transmitter into the camera, leaving the OSD pin open.

Camera-OSD Switch Connection

This section describes the physical connections for the camera and OSD switch board.

Diagram Description:

A 3-pin connector from the video transmitter connects to the camera's video output.
A 2-pin connector from the OSD switch board connects to the camera's OSD pins.
The OSD switch board has connections labeled: VBAT+, OSD, VID, GND, VSEN.
The camera back is labeled for S-WDR CAMERA.
The OSD switch front has control buttons: UP, DOWN, LEFT, RIGHT, MENU.

ℹ️ NOTICE: It is recommended to use a power distribution board.

❗ CAUTION: If you are using ESCs with active braking, we recommend powering the camera system through a BEC or voltage regulator.

FPV OSD Setup

Press and hold the top button for 3 seconds to access the OSD menu.

Main Menu Navigation

MENU: Push the center button to go to the main menu.
UP/DOWN: Move up and down through the menu options.
Left/Right: Modify the menu parameters.

OSD Menu Structure

The main menu includes the following options:

SETUP MENU: Accesses detailed settings.
EXIT: Exits the menu.

Setup Menu Options:

CAMERA ID: [On/Off] - Allows setup of pilot name and position.
PICT ADJUST: Adjusts picture settings like brightness, contrast, etc.
DAY/NIGHT: Sets camera mode for different lighting conditions.
LANGUAGE: Selects the menu language.
CAMERA RESET: Resets camera settings to default.

Detailed Settings Explained

1. Camera ID

Camera ID: [On/Off]. You can set the pilot name and its position on the screen.

Example display shows fields for CAMERA ID, FOXEER, time, and character selection for name and position.

2. PICT ADJUST

Adjusts the following picture parameters:

FLIP: Options: OFF, H-FLIP, V-FLIP, HV-FLIP.
BRIGHTNESS: Adjusts image brightness.
CONTRAST: Adjusts image contrast.
SHARPNESS: Adjusts image sharpness.
HUE: Adjusts color tint.
COLOR GAIN: Adjusts color saturation.

3. DAY/NIGHT

This setting includes 'AUTO' and 'MANUAL' modes. In 'MANUAL' mode, you can permanently set the camera to 'COLOR' or 'B/W' (Black/White).

Quick switch: At standby status, long press the right button on the OSD board to fast change the MODE. The current mode will show once at the TIMER place.

4. LANGUAGE

Supports 7 languages:

ENGLISH
DEUTSCH
FRANCAIS
PYCCKNN (Russian)
PORTUGUES
ESPANOL
中文 (Chinese)

5. Camera Reset

Resets camera settings.

6. EXIT

Options for saving changes:

Save All: Saves all setup configurations.
Not Save: Temporarily saves values, but they are lost upon power off.
Cancel: Cancels the current setup.

OSD Menu Configuration Items

These are specific settings configurable within the OSD menu:

DISPLAY
1. TIME: [On/Off]
2. POWER: [On/Off]
3. VOL ALARM: You can set a voltage threshold. Use the LEFT/RIGHT buttons to decrease or increase the value. The default is 3.6V.
4. V CAL: Voltage calibration, with a range from -0.5 to 0.5.
5. MODE: Options include DAY, NIGHT, LED, and B&W.
6. N/P: NTSC/PAL switchable.
7. SIZE: 4:3 / 16:9 switchable.
8. VER: FOXEER_V4.0.
9. EXIT

	FOXEER Predator Micro & Mini FPV Camera User Manual Comprehensive user manual for the FOXEER Predator Micro and Mini FPV cameras, covering setup, OSD menu configuration, picture adjustments, language settings, and camera reset options.
	FOXEER CAT MINI & CAT MICRO Camera User Manual and Settings Guide Comprehensive user manual for FOXEER CAT MINI and CAT MICRO FPV cameras, detailing connection diagrams, menu navigation, and settings for image, exposure, AWB, day/night, and system configurations.
	Foxeer DigiSight Nano FPV Camera User Manual Comprehensive guide to setting up and operating the Foxeer DigiSight Nano FPV camera, covering connections, OSD menu, image adjustments, and language settings.
	Foxeer Razer Mini & Micro FPV Camera User Manual and Settings Guide This guide provides detailed instructions for setting up and operating the Foxeer Razer Mini and Micro FPV cameras. It covers camera connections, OSD switch functions, main menu navigation, and advanced settings such as Auto Exposure (AE), Auto White Balance (AWB), Image Enhancement, Video Settings, and Day/Night modes.
	FOXEER MONSTER Series Camera OSD and Settings Manual Comprehensive guide to setting up and configuring FOXEER MONSTER MICRO PRO and MONSTER MINI PRO cameras, covering OSD menus, exposure, shutter, image adjustments, and more.
	Foxeer Predator 5 FPV Camera User Manual Comprehensive user manual for the Foxeer Predator 5 FPV camera, detailing setup, features, OSD menu, and connections for hobby-grade remote-controlled vehicles.
	FOXEER T-Rex FPV Camera Manual: Setup, Settings, and Connections Comprehensive guide for FOXEER T-Rex, T-Rex Mini, and T-Rex Micro FPV cameras. Covers video transmitter and OSD connections, menu system navigation, and detailed settings for image, AWB, exposure, day/night modes, language, and system configuration.
	FOXEER Toothless Series FPV Camera System User Manual User manual for the FOXEER Toothless Nano, Mini, and Micro FPV camera systems, detailing connections, menu settings, and operational parameters.