Minoston MS10Z Z-Wave Plus Smart On/Off Switch

Installation and Operation Guide

Product Overview

The Minoston MS10Z is a Z-Wave Plus certified smart on/off switch designed for modern home automation. It offers versatile control options, including manual operation and wireless Z-Wave control, supporting 3-way configurations and custom scene functions. It features S2 security, a 500 series Z-Wave chip, and over-the-air (OTA) firmware updates.

Key Features

Manual and wireless on/off control.
Supports 3-way control with regular or dummy switches (neutral wire required).
Two customizable scene functions.
Built-in Z-Wave Plus signal repeater/range extender.
S2 security protocol and latest 500 series Z-Wave chip.
OTA firmware updates.
Customizable parameter settings.
Restores previous state after power failure.

Specifications

Model: MS10Z

Power: 120VAC, 60Hz

Frequency: 908.42 MHz

Maximum Load: 960W Incandescent, ½ HP Motor or 1800W (15A) Resistive

Temperature Range: 32° F to 104° F (0° C to 40° C)

Usage: Indoor use in dry locations only.

Safety Warnings and Precautions

CAUTION - PLEASE READ! This device is intended for installation in accordance with the National Electric Code and local regulations. If unsure, consult a qualified electrician.

WARNING - SHOCK HAZARD: Turn off power at the circuit breaker before installation. Ensure all wiring connections are made with the power off.

MEDICAL EQUIPMENT: Do not use this switch to control medical or life support equipment. Z-Wave devices should never be used for this purpose.

CONTROLLING APPLIANCES: Exercise extreme caution when using Z-Wave devices to control appliances. Avoid including devices that control hazardous appliances in groups or scenes.

FCC / IC Compliance: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Modifications may void authority to operate.

Part 1: Installation

Turn off power: Locate and turn off the circuit breaker for the light control. Verify power is off.
Detach old switch: Unscrew the old switch from the wall box.
Identify wires:
- LINE (Hot): Typically Black (connected to power)
- NEUTRAL: Typically White
- LOAD: Typically Black (connected to lighting)
- GROUND: Green or Bare Copper
- TRAVELER: Red or Other (only for 3-way installations)
Install wires: Connect the wires to the MS10Z switch according to the wiring diagrams provided (single-pole or 3-way). Ensure the neutral wire is correctly connected in 3-way setups.
Fix the shell: Secure the switch to the wall box using the provided screws.
Turn on power: Restore power at the circuit breaker and test the switch.

Note: For 3-way setups, use only an On/Off, 3-way slave switch (non-dimming). The Traveler terminal is only used for 3-way wiring.

Wiring Diagrams:

Single Switch Wiring:

Diagram Description: Shows connections for Line, Load, Neutral, and Ground wires to the switch in a standard single-pole setup.

3-Way Switch Wiring:

Diagram Description: Illustrates the wiring for a 3-way setup, including connections for Line, Load, Neutral, Ground, and Traveler wires between the smart switch and a regular 3-way switch. Two options (Option 1 and Option 2) are presented, showing different configurations for the traveler wire.

Important Note: If your Line and Load wires are not in the same box, please contact Minoston for a custom schematic.

Part 2: Switch Setup

Local Button Functions

Press 1x: Turn output ON or OFF.
Press 2x quickly: Send Scene 1 / Scene 2 command.
Press 3x quickly: Initiate inclusion or exclusion process.
Press 6x quickly: Change Parameter 2 (LED Indicator Status).
Press 7x quickly: Change Parameter 1 (Button Function Setting).
Press 8x quickly: Change Parameter 8 (Restore State after Power Failure).
Factory Reset: Click Z-Wave button 2 times quickly, then hold for at least 10 seconds.

Z-Wave Network Inclusion

1. Set your Z-Wave controller/hub to inclusion mode.

2. Triple press the Up/Down push button quickly on the MS10Z to include it in the network.

Z-Wave Network Exclusion

1. Set your Z-Wave controller/hub to exclusion mode.

2. Triple press the Up/Down push button quickly on the MS10Z to exclude it from the network.

Scene Functions

Scene 1: Tap-Down-2
Scene 2: Tap-Up-2

Works with Alexa & Google Assistant

Requires a compatible Z-Wave hub to interact with Amazon Alexa or Google Home services.

LED Status (Blue)

Default (Off): LED is ON when the switch is OFF, and LED is OFF when the switch is ON.
Value 1: LED is ON when the switch is ON, and LED is OFF when the switch is OFF.
Value 2: LED is always OFF.
Value 3: LED is always ON.
Flashing quickly: Configuration succeed, inclusion/exclusion, parameter change.
Flashing two times: Factory default, change LED status, change locally button function, restores state after power failure.

Parameter Settings

Parameter	Available Settings	Operation
Parameter 1: Button Function Setting Size=1, Value=0 (Default), 1, 2	Value 0: Up button ON, Down button OFF. Value 1: Up button OFF, Down button ON. Value 2: Both buttons change light state. Note: Switching values requires quick presses of button 7 times.	Quick press the switch button 7 times.
Parameter 2: LED Indicator Status Setting Size=1, Value=0 (Default), 1, 2, 3	Value 0: LED ON when switch OFF, LED OFF when switch ON. Value 1: LED ON when switch ON, LED OFF when switch OFF. Value 2: LED always OFF. Value 3: LED always ON. Note: Switching values requires quick presses of button 6 times.	Quick press the switch button 6 times.
Parameter 8: Restores State after Power Failure Size=1, Value=1, 2 (Default)	Value 1: Switch is OFF after power failure. Value 2: Switch returns to state before power failure. Note: Switching values requires quick presses of button 8 times.	Quick press the switch button 8 times.
Parameter 4: Auto Turn-Off Timer Size=4, Values: 0 – 65535 (minutes)	Value 0 (default): Set up on the hub. The number entered corresponds to minutes.	Set up on the hub.
Parameter 6: Auto Turn-On Timer Size=4, Values: 0 – 65535 (minutes)	Value 0 (default): Set up on the hub. The number entered corresponds to minutes.	Set up on the hub.
Parameter 7: Direct Control of Other Devices Size=1, Default = 1	Value 00 – none Value 01 - local Value 02 - 3way Value 03 - 3way & local Value 04 - z-wave hub Value 05 - z-wave hub & local Value 06 - z-wave hub & 3-way Value 07 - z-wave hub & local & 3way Value 08 - timer Value 09 - timer & local Value 10 - timer & 3-way Value 11 - timer & 3-way & local Value 12 - timer & z-wave hub Value 13 - timer & z-wave hub & local Value 14 - timer & z-wave hub & 3-way	Set up on the hub.

Association Group Information

Group 1: Z-Wave Plus Lifeline (supports 1 node ID). Must be assigned the Node ID of the primary controller.
Group 2: Send Basic Set ON/Off (supports up to 5 node IDs).

Association setup is performed via the Z-Wave hub.

Device Information

Generic Device Class: 0x10 - GENERIC_TYPE_SWITCH_BINARY

Specific Device Class: 0x01 - SPECIFIC_TYPE_POWER_SWITCH_BINARY

Troubleshooting

If the smart switch does not work properly, check the wiring connections and ensure the power is correctly supplied. Refer to the parameter settings for specific functions. For any installation questions, contact Minoston at ask@minoston.com.

Warranty

Minoston warrants this product to be free from manufacturing defects for one year from the original date of purchase. This warranty covers repair or replacement and does not extend to consequential damages. This warranty is in lieu of all other warranties, expressed or implied.

Contact

For support or questions, please contact Minoston at ask@minoston.com.

	Minoston MS13Z Smart Toggle Dimmer Switch Installation and Operation Guide Comprehensive guide for installing and operating the Minoston MS13Z Smart Toggle Dimmer Switch, including wiring diagrams, features, parameter settings, troubleshooting, and warranty information.
	Minoston S2 Remote Control Switch MR40Z(ZW924) User Manual and Specifications Comprehensive guide to the Minoston S2 Remote Control Switch (MR40Z(ZW924)), covering specifications, setup, Z-Wave integration, configuration parameters, scene control, association groups, command classes, and important safety instructions.
	Minoston MP31ZP Z-Wave Plug with Energy Monitor User Manual User manual for the Minoston MP31ZP Z-Wave Plug with Energy Monitor. Details features, specifications, Z-Wave network setup, parameter configurations, and safety guidelines for smart home integration.
	Minoston S2 Remote Control Switch (800S) - User Manual and Setup Guide Comprehensive guide for the Minoston S2 Remote Control Switch (Model MR40Z(ZW924)), covering setup, Z-Wave integration, SmartThings compatibility, configuration parameters, scene control, and safety instructions.
	Minoston MS12ZS Smart On/Off Toggle Switch Manual and Specifications User manual and technical specifications for the Minoston MS12ZS Smart On/Off Toggle Switch. Learn about Z-Wave integration, installation, configuration parameters, association groups, and warranty.
	Minoston MS10ZS Smart On/Off Switch Manual and Specifications Comprehensive guide to the Minoston MS10ZS Smart On/Off Switch, covering installation, features, Z-Wave configuration, and troubleshooting. Includes FCC and IC compliance information.
	Minoston MS12ZS Smart On/Off Toggle Switch Manual Detailed manual for the Minoston MS12ZS Smart On/Off Toggle Switch, covering regulatory compliance, warranty, specifications, installation, Z-Wave features, configuration parameters, and factory reset. Learn how to integrate this device into your smart home network.
	Minoston MP21Z Z-Wave Mini Smart Plug User Manual and Setup Guide Comprehensive guide for the Minoston MP21Z Z-Wave mini smart plug, covering setup, network configuration, parameter settings, features, and safety precautions for smart home integration.