TEGERA® 432 Protective Gloves

Product Specific Information

Outer Material Specification

Polyurethane

Inner Material Specification

HPPE (High performance polyethylene), elastane, nylon

Size Range (EU)

5, 6, 7, 8, 9, 10, 11

EU-Type Examination (Module B)

Issued by Notified Body: 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07 France

Packaging

12 Pairs

Origin

Made in China

Importer Information

UK Importer: Ejendals ltd, Sweden House, 5 upper Montagu Street, London, England, W1 2AG

Manufacturer: ejendals ab, Limavägen 28, SE-793 32 Leksand, Sweden

Contact: info@ejendals.com | order@ejendals.com | www.ejendals.com

Declaration of Conformity

www.ejendals.com/conformity

General Instructions for Use

Category

Category II

Introduction

Carefully read these instructions before using this product.

Explanation of Pictograms

0 = Below the minimum performance level for the given individual hazard

X = Not submitted to the test or test method not suitable for the glove design or material

Warning

This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.

Performance Ratings (EN 388:2016 +A1:2018)

Protective gloves against mechanical risks. Protection levels are measured from area of glove palm.

Warning: For gloves with two or more layers the overall classification of EN 388:2016 +A1:2018 does not necessarily reflect the performance of the outmost layer. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result. Do not use these gloves near moving elements or machinery with unprotected parts.

General Requirements and Test Methods (EN ISO 21420:2020)

Finger dexterity test

Min. 1; Max. 5

Abrasion resistance (ANSI 105-2016)

Levels 1-6

Cut resistance (ANSI 105-2016)

Levels A1-A9

Fitting and Sizing

All sizes comply with the EN ISO 21420:2020 for comfort, fit and dexterity, if not explained on the front page. If the short model symbol is shown on the front page, the glove is shorter than a standard glove, in order to enhance the comfort for special purposes - for example fine assembly work. Only wear the products in a suitable size. Products which are either too loose or too tight will restrict movement and will not provide the optimal level of protection.

Storage and Transport

Ideally stored in dry and dark condition in the original package, between +10°C - +30°C.

Inspection Before Use

Wash and dry your hands completely before donning the gloves. Before use, inspect the gloves for any defects or imperfections and avoid wearing damaged gloves. Ensure the gloves fit well. When removing your gloves, hold the outside edge of the glove and peel the glove away and hold in gloved hand. Use ungloved fingers to slide and peel the remaining glove off from the inside. Where hazardous chemicals are handled do not touch the outer surface of the glove.

Shelf Life

The nature of the materials used in this product means that the life of this product cannot be determined as it will be affected by many factors, such as storage conditions, usage etc.

Care and Maintenance

Gloves/sleeves that can be mechanically washed will carry laundry symbols. It is the customer or launderer who is responsible for the performance of the gloves after laundering when the gloves have already been used. Ejendals cannot be held liable for this.

Disposal

According to local environmental legislations.

Allergens

The glove contains natural rubber which may cause allergy.

This product may contain components that may be a potential risk to allergic reactions. Do not use in case of hypersensitivity signs. For more information contact Ejendals.

Latex free: No