MICKE Desk Assembly Instructions
This document provides step-by-step instructions for assembling the IKEA MICKE desk. Please ensure all parts are present before beginning.
Tools Required
The following tools are recommended for assembly: Screwdriver (Phillips head) [Tool icon ?], Hammer [Tool icon ?].
General Assembly Guidance
Assembly Precautions:
- Assemble on a clean, flat, and protected surface to prevent scratches [X symbol ❌].
- It is recommended to have two people for certain steps to ensure stability and safety [Two people icon ???].
- Do not force parts together; check alignment carefully.
- If you encounter any issues or are unsure about a step, please refer to IKEA customer support. [Question mark icon ❓, Phone icon ?]
Parts List
Hardware and Components:
- Screw (100086): 3x
- Screw (110519): 4x
- Screw (100365): 16x
- Dowel (118331): 22x
- Cam Lock (110126): 4x
- Cam Lock (103430): 14x
- Cam Lock (103114): 4x
- Wooden Dowel (121030): 1x
- Hex Key (100092): 1x
- Wooden Dowel (101344): 19x
- Drawer Slide (112482): 2x
- Drawer Front/Back Panel (153549): 2x
- Cable Grommet (112519, 121338): 1x
- Hexagonal Connector (10081375): 2x
- Cable Grommet (121186, 121208): 1x
Assembly Steps
Step 1
Insert 2x wooden dowels (101344) into the base panel. Attach the two side panels to the base panel using 2x dowels (118331) and secure with cam locks.
Step 2
Insert 2x wooden dowels (101344) into the bottom edge of each of the two vertical support panels.
Step 3
Attach the vertical support panels to the base assembly. Secure using 2x cam locks (103114) per panel.
Step 4
Fold a panel as shown in the diagram. This step likely prepares a component for attachment.
Step 5
Insert 2x screws (110519) into the pre-drilled holes on the drawer side panels.
Step 6
Attach the drawer slides (112482) to the inner sides of the desk frame.
Step 7
Attach the drawer slides (100365) to the sides of the drawer box.
Step 8
Attach the back support panel to the desk frame using 4x screws (1010344) and 4x wooden dowels (1010344).
Step 9
Attach the second back support panel to the desk frame using 4x screws (1010344) and 4x wooden dowels (1010344).
Step 10
Insert 1x dowel (118331) into the designated holes on the frame.
Step 11
Attach a vertical support piece using 1x wooden dowel (101344).
Step 12
Insert 1x cam lock (103430) and 1x cam lock (110126) into the frame components.
Step 13
Attach a horizontal panel (likely the drawer base or a shelf) using 8x dowels (118331).
Step 14
Attach 1x drawer slide (100365) to each of the two horizontal panels using screws (100365).
Step 15
Attach the side panels to the main frame using 2x dowels (101344).
Step 16
Secure the assembly using 8x cam locks (103430) and 8x cam locks (110126).
Step 17
Attach the side panels to the desk structure, securing with 4x wooden dowels (101344).
Step 18
Attach the back panel using 3x screws (100086) and 3x wooden dowels (121030). A hex key (100092) is used for tightening.
Step 19
Secure the tabletop to the frame using 9x dowels (118331).
Step 20
Slide the assembled drawer into the desk frame. Ensure it moves smoothly.
Step 21
Attach 4x cam locks (110126) to the drawer assembly.
Step 22
Attach 3x cam locks (103430) to the drawer assembly.
Step 23
Attach 2x drawer supports/handles (153549) to the drawer front.
Step 24
Attach 2x protective pads (10081375) to the bottom of the desk legs.
Step 25
Attach 1x drawer runner (100365) to each side of the desk frame, securing with screws (100365).
Step 26
Insert the assembled drawer into the desk, aligning the runners.
Step 27
Insert the cable grommet (112519, 121338) into the desk's cable hole. Insert 4x cable clips/holders (121208, 112186) into the designated slots.
