VEVOR Wall Mounted Projection Screen

Introduction

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. VEVOR will not provide further notification for any technology or software updates on our product.

Warning

[Warning Symbol] Please read this manual carefully before using the product. Failure to do so may result in serious injury.

Assembly Warnings

• Please read and observe carefully all the assembly instructions before beginning assembly.
• [Two People Required] Unit should be assembled by two or more people.
• [Child/Animal Climbing Warning] Please do not let your child climb on the product. If you have kids or animals who like to climb, we highly recommend using the wall anchors and brackets/straps that come with the package.

Assembly Precautions

1. Assemble only according to these instructions. Improper assembly can create hazards. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. Keep the assembly area clean and well-lit. Keep bystanders out of the area during assembly. Do not assemble when tired or when under the influence of alcohol, drugs or medication.
2. The product capabilities apply to properly and completely assembled products only.
3. Assemble on a flat, level, hard and smooth surface capable of safely supporting the Wall Mounted Projection Screen.
4. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

SAVE THESE INSTRUCTIONS

Use Precautions

To Prevent Serious Injury and Death from Tipping:

1. This product is not a toy. Do not allow children to play with or near this item.
2. Do not exceed weight capacities before moving.
3. Use only on a flat, hard and smooth surface capable of safely supporting a fully loaded Wall Mounted Projection Screen.
4. Use as intended only.
5. The screen cannot be folded. Do not use fingers or hard objects to touch the screen surface. Do not splash milk, fruit juice or other chemical doses onto the screen surface. Keep the screen far away from high temperature objects or fire.
6. If the screen is dirty, please wash the screen gently by a broom or a cotton ball. Do not use organic solvents to clean the screen surface.
7. When pulling the screen down, it must be done slowly and vertically. Do not pull it roughly. Please stop pulling as soon as the black border is out, or the screen will be jammed or injured. Then send the screen to the maintenance center.
8. After using, put the screen back into the housing to avoid being polluted. If not using it for a long time, please take the screen from the wall and pack it in a carton.

Inspect before every use; do not use if parts are loose or damaged.

Technical Specifications

*Products such as specifications, appearance, and design are subject to modification without prior notice.

Package Contents

Model Numbers: ES60, ES120, ES72

The package typically includes the projection screen, a power plug, a remote control, and a transmitter.

Useful Instructions

Model Numbers: ES60, ES120, ES72

1. The screen should be switched to a suitable power supply. It can be 220V/50Hz, 230V/50Hz, or 110V/60Hz, 120V/60Hz, but the motor's power must be the same as the local voltage and frequency.
2. The screen can be used with or without the remote controller. The remote control system can be radio type or infrared type. Normally, if a remote control system is needed, a radio remote controller is supplied, but an infrared type controller is also available for a special requirement. These two different controlling functions cannot be combined in one control system.
3. Normally, a synchronized motor is installed inside the housing, but a tubular motor is also available for a special requirement.
4. If the remote control system is not accompanied, the screen can be operated by the control box directly. Just push the UP/DOWN /STOP button on the control box to operate the screen. Alternatively, the screen can be operated by the remote controller.

Remote Control Instruction Manual

Specifications:

• Voltage: AC220V/110V ±10%
• Load Power: <500W
• Remote Control Frequency: RF: 315MHZ/433.92MHZ
• Remote Control Distance: RF: ≤50 Meter (field)

Matters Need Attention:

• When wiring or conducting maintenance on the receiver, the power supply must be cut off.
• If the remote control is not responding or has reduced range, please replace the battery. Battery model: 23A12V.

FCC Information

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This product may cause harmful interference.
• This product must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the product.

Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This product generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions, complying with exposure requirements.

Manufacturer and Importer Information

Manufacturer: Shenzhen Future Information Technology Co., Ltd

Address: No.15 Dayang Industrial Zone, Lougang Village, Songgang town, Bao'an District, ShenZhen, China

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC REP: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.