VEVOR Projection Screen User Manual

VEVOR is committed to providing tools at competitive prices. Expressions like "Save Half" are estimates of potential savings compared to major top brands and may not apply to all categories. Please verify savings when ordering.

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret its user manual. Product appearance is subject to the received product. VEVOR will not provide further notice for technology or software updates.

WARNING

Please read this manual carefully before using the product. Failure to do so may result in serious injury.

ASSEMBLY PRECAUTIONS

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or under the influence of alcohol, drugs, or medication.
6. Product capabilities apply only to properly and completely assembled products.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Projection Screen.
8. For additional information regarding parts, refer to the Assembly Diagram in this manual. Unwrap and separate all parts in a clean work area.

SAVE THESE INSTRUCTIONS

USE PRECAUTIONS

TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

1. This product is not a toy. Do not allow children to play with or near this item.
2. Do not exceed weight capacities before moving.
3. Use only on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded Projection Screen.
4. Use as intended only. Inspect before every use; do not use if parts are loose or damaged.

TECHNICAL SPECIFICATIONS

*Specifications, appearance, and design are subject to modification without prior notice.

PACKAGE CONTENTS

ASSEMBLY STEPS

Step 1: Frame Assembly

Splice the long borders together to form the main frame structure.

Step 2: Frame Reinforcement

Insert corner codes into the slots at both ends of the short frames. Connect the two short frames to the two long frames and tighten the screws. After assembly, turn the frame over and check the gaps at the four corners on the front (suede side). Readjust if any gap is too large.

Step 3: Screen Material Preparation

Unfold the screen material (curtain). Thread the glass fiber tubes along the designated channels on the long and short sides of the screen material.

Step 4: Attaching the Screen Material

Hang the springs. Position the projection surface of the screen material face down, centered and flat on the assembled frame. First, attach the screen material to the four corners of the frame using the springs. Clamp the support rods onto the groove between the upper and lower frames. Install all remaining springs according to the holes in the screen material, following the indicated order. Note: The quantity of springs may vary by model.

Step 5: Wall Mounting and Final Installation

Measure the width (w) and height (h) of the assembled frame. Install two wall hangings on the wall using expansion rubber plugs, ensuring they are level. For a more secure mount, additional wall hangings can be installed upside down below the first row. The vertical distance between the centers of the upper and lower rows of holes should be H1 = H - 40mm. Hang the screen onto the first row of wall hangings. Gently press down the lower frame of the screen and push the screen towards the wall simultaneously to secure the lower frame onto the second row of wall hangings. The installation is now complete.

COMPLETION INFORMATION

Manufacturer: Shanghaimuxinmuyeyouxiangongsi. Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia.

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730.

EC REP: E-CrossStu GmbH. Mainzer Landstr.69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX.

For Technical Support and E-Warranty Certificate, visit: www.vevor.com/support